Bolt looseness monitoring based on damping measurement by using a quantitative electro-mechanical impedance method
Source abstract
Abstract
Abstract In-situ bolt looseness monitoring is very important for the stability and safety of engineering structures. The electro-mechanical impedance (EMI) method, which had been intensively studied in structure health monitoring, has offered a feasible solution. However, in traditional EMI method, the lack of modal pre-selection leads to dense resonant peaks which brings difficulty to signal analysis. The commonly used statistical damage indices typically do not have physics meaning and may fail to distinguish the defects from the environmental changes. In this work, a quantitative EMI (Q-EMI) method was proposed to measure the damping of structures for bolt looseness monitoring. The in-plane excitation method based on distributed thickness-shear-mode piezoelectric transducers was used for selective excitation of vibration modes. The modal-related sensitivity variation was theoretically analyzed and then validated by experiments. Three different specimens were tested and the results showed that during bolt loosening, the modal damping increased by 100%–300%, while the resonance frequency of the structure only decreased by several percent. Moreover, it was found that the loosened bolt may be located using the variation of modal-related sensitivity. Due to its good performance and easy mounting, the proposed Q-EMI method is very promising for bolt looseness monitoring and is expected to be widely used in near future.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Ultrasonics and Acoustic Wave Propagation · Structural Health Monitoring Techniques · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Bickford · 2007
2. Study on self-loosening of bolted joints excited by dynamic axial load10.1016/j.triboint.2017.05.037 ↗
3. Review of bolted connection monitoring10.1155/2013/871213 ↗
4. A review paper on looseness detection methods in bolted structures10.1590/1679-78254231 ↗
5. A review of bolt tightening force measurement and loosening detection10.3390/s20113165 ↗
6. Force identification in bolts of flange connections for structural health monitoring and failure prevention10.1016/j.prostr.2017.07.142 ↗
7. Combination of longitudinal and transverse ultrasonic waves for in situ control of the tightening of bolts10.1115/1.2748821 ↗
8. Contactless measurement of bolt axial stress using a shear-wave electromagnetic acoustic transducer10.1016/S0963-8695(00)00055-4 ↗
9. Measurement of axial stress using mode-converted ultrasound10.1016/j.ndteint.2008.09.005 ↗
10. A piezoelectric active sensing method for quantitative monitoring of bolt loosening using energy dissipation caused by tangential damping based on the fractal contact theory10.1088/1361-665X/aa9a65 ↗
11. Quantitative health monitoring of bolted joints using a piezoceramic actuator–sensor10.1088/0964-1726/13/1/003 ↗
12. Bolt looseness detection based on piezoelectric impedance frequency shift10.3390/app6100298 ↗
13. Overview of piezoelectric impedance-based health monitoring and path forward10.1177/05831024030356001 ↗
14. Feasibility of using impedance-based damage assessment for pipeline structures10.1002/eqe.72 ↗
15. Impedance based bolt pre-load monitoring using piezoceramic smart washer10.1088/1361-665X/aa6a8e ↗
16. A fractal contact theory based model for bolted connection looseness monitoring using piezoceramic transducers10.1088/1361-665X/aa6e93 ↗
17. Proof-of-concept study of monitoring bolt connection status using a piezoelectric based active sensing method10.1088/0964-1726/22/8/087001 ↗
18. Detection of bolt loosening in C–C composite thermal protection panels: I. Diagnostic principle10.1088/0964-1726/15/2/041 ↗
19. Shear horizontal wave transducers for structural health monitoring and nondestructive testing: a review10.1016/j.ultras.2021.106355 ↗
20. Guided wave based structural health monitoring: a review10.1088/0964-1726/25/5/053001 ↗
21. Rose · 2014
22. An impedance method for dynamic analysis of active material systems10.1115/1.2930387 ↗
23. Giurgiutiu · 2007
24. Electro-mechanical impedance method for crack detection in thin plates10.1177/104538901320560355 ↗
25. An impedance-based structural health monitoring approach for looseness identification in bolted joint structure10.1007/s13349-018-0307-2 ↗
26. Impedance-based structural health monitoring incorporating neural network technique for identification of damage type and severity10.1016/j.engstruct.2012.01.012 ↗
27. Synchronous detection of bolts looseness position and degree based on fusing electro-mechanical impedance10.1016/j.ymssp.2022.109068 ↗
28. Axial force measurement of the bolt/nut assemblies based on the bending mode shape frequency of the protruding thread part using ultrasonic modal analysis10.1016/j.measurement.2020.107914 ↗
29. EMI based multi-bolt looseness detection using series/parallel multi-sensing technique
30. Fatigue life estimation of a 1D aluminum beam under mode-I loading using the electromechanical impedance technique10.1088/0964-1726/20/12/125001 ↗
31. Modeling the dynamics of mechanical joints10.1016/j.ymssp.2011.01.010 ↗
32. Relative baseline features for impedance-based structural health monitoring10.1177/1045389X14551435 ↗
33. Ehrlich · 2014 · vol 1 · 239
34. Quantitative electromechanical impedance method for nondestructive testing based on a piezoelectric bimorph cantilever10.1088/0964-1726/24/6/065038 ↗
35. In-plane selective excitation of arbitrary vibration modes using thickness-shear (d 15) piezoelectric transducers10.1088/1361-665X/ac48bb ↗
36. Evaluation of characterization indexes and minor looseness identification of flange bolt under noise influence10.1109/ACCESS.2020.3019416 ↗
37. New method enables multifunctional measurement of elastic moduli and internal frictions10.1063/5.0034801 ↗
38. A modified piezoelectric ultrasonic composite oscillator technique for simultaneous measurement of elastic moduli and internal frictions at varied temperature10.1063/1.5135360 ↗
39. Trefethen · 2000
40. Bolt-joint structural health monitoring by the method of electromechanical impedance10.1108/AEAT-01-2013-0006 ↗