A two-stage electromagnetic coupling and structural optimisation for vibration energy harvesters
Source abstract
Abstract
Abstract This paper demonstrates a two-stage optimisation for a single-degree-of-freedom (SDOF) electromagnetic vibration energy harvester under a harmonic base excitation vibration. In this paper, a designed cantilever beam was used to verify the optimisation methods. The dynamics of the beam was modelled using the Euler-Bernoulli beam theory. By deriving the exact expression of the power output under the optimum load resistance condition, the correct electromagnetic coupling coefficient was determined. The first optimisation stage involves maximising this coefficient by considering several coils and magnet parameters, allowing at this stage to define the electrical efficiency of the harvester which is described as the ratio of the harvester’s power output to its power limit. The experimentally determined power output for this stage was 3.51 mW. The structural aspects of the harvester were then optimised by considering the addition and placement of proof masses and the structural dimensions of the harvester. This part represents the second optimisation and determines the power limit of the harvester. An experimental power output of 7.95 mW was achieved in this stage. All experimental results displayed a good agreement with the derived theoretical model, recording an error of less than 10.0%, hence validating the theoretical model. The first optimisation stage presented here can be applied to any linear electromagnetic SDOF harvester whereas the second optimisation stage can be easily modified to suit different structural considerations. Additionally, both stages can also be slightly modified to account for rotational systems.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Innovative Energy Harvesting Technologies · Wireless Power Transfer Systems · Vibration Control and Rheological Fluids
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Analysis of a micro-electric generator for microsystems10.1016/0924-4247(96)80118-X ↗
2. Energy scavenging for wireless sensor nodes with a focus on vibration to electricity conversion
3. Electromagnetic vibration energy harvesting device optimization by synchronous energy extraction10.1016/j.sna.2011.06.024 ↗
4. Vibration energy harvesting system for railroad safety based on running vehicles10.1088/0964-1726/23/12/125046 ↗
5. Comparison of electromagnetic and piezoelectric vibration energy harvesters: model and experiments10.1016/j.sna.2012.04.033 ↗
6. Piezoelectric MEMS for energy harvesting10.1557/mrs.2012.275 ↗
7. Design and optimization of an electromagnetic vibration energy harvester using dual halbach arrays10.1109/TMAG.2015.2437892 ↗
8. Simulation and testing of a micro electromagnetic energy harvester for self-powered system10.1063/1.4861208 ↗
9. Spreeman · 201210.1007/978-94-007-2944-5 ↗
10. Enhanced vibrational energy harvester based on velocity amplification10.1177/1045389X13498316 ↗
11. A velocity-amplified electromagnetic energy harvester for small amplitude vibration10.1088/1361-665X/aa7e54 ↗
12. Ouput power and efficiency of electromagnetic energy harvesting systems with constrained range of motion10.1088/0964-1726/22/12/125009 ↗
13. Capturing energy from ultra-low frequency vibrations and human motion through a monostable electromagnetic energy harvester10.1016/j.energy.2018.12.053 ↗
14. A micro electromagnetic generator for vibration energy harvesting10.1088/0960-1317/17/7/007 ↗
15. Increased power output of an electromagnetic vibration energy harvester through anti-phase resonance10.1016/j.ymssp.2018.06.012 ↗
16. Electroelastic modelling and experiment validations of piezoelectric energy harvesting from broadband random vibrations of cantilevered bimorphs10.1088/0964-1726/22/1/015002 ↗
17. Modeling and experimental verification of proof mass effects on vibration energy harvester performance10.1088/0964-1726/19/4/045023 ↗
18. On mechanical modelling of cantilevered piezoelectric vibration energy harvesters10.1177/1045389X07085639 ↗
19. Squeeze film air damping in MEMS10.1016/j.sna.2007.01.008 ↗
20. Review and comparison of different support loss models for micro-electro-mechanical systems resonators undergoing in-plane vibration10.1177/0954406211413351 ↗
21. Internal friction in solids III: experimental demonstration of thermoelastic internal friction10.1103/PhysRev.53.100 ↗
22. On mechanical damping of cantilever beam-based electromagnetic resonators10.1016/j.ymssp.2018.09.023 ↗
23. Optimization of an electromagnetic energy harvesting device10.1109/TMAG.2006.879447 ↗
24. Numerical modeling of shape and topology optimisation of a piezoelectric cantilever beam in an energy‐harvesting sensor10.1007/s00366-016-0460-3 ↗
25. Automatic machines
26. Enamelled Copper Wire
27. Super Enameled & Annealed Copper Wires, Ashkay Insulated Conductors
28. Innovative needle winding method using curved wire guide in order to significantly increase the copper fill factor10.1109/ICEMS.2014.7014018 ↗
29. Analytic expression of magnetic field distribution of rectangular permanenet magnets10.1007/BF02437333 ↗
30. Design of wideband vibration-based electromagnetic generator by means of dual-resonator10.1016/j.sna.2014.03.037 ↗
31. Damping ratio and power output prediction of an electromagnetic energy harvester designed through finite element analysis10.1016/j.sna.2018.12.041 ↗
32. Comparison of linear beam theories10.1016/j.mcm.2008.06.006 ↗
33. Review of the troughability test ISO 703 for quantifying a uniform transverse bending stiffness for conveyor belts10.1016/j.acme.2016.10.007 ↗