journal article·2024-09-01Open access

Active vibration control of gearbox housing using inertial mass actuators

Sherif Okda, Sneha Rupa Nampally, Mauro Fontana, Sven Herold, Rainer Nordmann, Stephan Rinderknecht, Tobias Melz

Smart Materials and Structures· Volume 33· Issue 9

Abstract

Abstract Reducing carbon emissions is a primary goal in the global effort to combat climate change. Decreasing the weight of a vehicle improves efficiency and significantly reduces emissions. One of the main contributors to the vehicle’s weight is the gearbox. However, this approach presents a challenge as lightweight transmission systems experience higher vibrations and noise emission levels. In this paper, an economical active vibration control system is developed to control the vibration levels of an automotive gearbox housing. The gearbox’s mounting points are targeted to reduce the transmitted vibrations to the car cabin. The active control system aims to target high-frequency vibrations between 1000 Hz and 5000 Hz. A compact piezoelectric inertial mass actuator is designed and tested on a gearbox-constructed setup that simulates the vibrations and noise similar to a commercial automotive transmission system. The developed test-rig is excited by a piezo stack actuator at the input shaft. Filtered-x least mean square algorithm is implemented on a high-speed microcontroller, and the vibration levels are significantly reduced using the active system. An average reduction of approximately 8.5 dB is achieved between 1000 Hz and 1500 Hz, an average reduction of approximately 14 dB is obtained between 1500 and 2000 Hz, and an average reduction of 10.8 dB is attained between 2500 and 5000 Hz.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Tribology and Lubrication Engineering · Iterative Learning Control Systems · Gear and Bearing Dynamics Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Lightweight gearbox housing with enhanced vibro-acoustic behavior through the use of locally resonant metamaterials10.1016/j.apacoust.2023.109435 ↗
2. Application of metal rubber for semi-active vibration control of mechanical transmission systems10.1177/10775463231192747 ↗
3. Gearbox noise and vibration prediction and control10.20855/ijav.2009.14.2242 ↗
4. Active control of gear vibration using specially configured sensors and actuators10.1088/0964-1726/9/3/315 ↗
5. Active vibration control of planetary gears by pole placement10.1088/1742-6596/1264/1/012004 ↗
6. Experimental study on active vibration control of a gearbox system10.1016/j.jsv.2004.03.043 ↗
7. Experimental analysis of an active vibration control system for gearboxes10.1088/0964-1726/13/5/027 ↗
8. Comparative analysis of actuator concepts for active gear pair vibration control10.1016/S0022-460X(03)00072-5 ↗
9. Multi-channel active gear pair vibration control with an electronically commutated motor as actuator
10. Active control of gear pair vibration with an electronically commutated motor as actuator
11. Active vibration control of a single-stage spur gearbox10.1016/j.ymssp.2016.08.032 ↗
12. Active reduction of gear mesh vibrations by drive torque control
13. Actuator design and experimental validation for active gearbox vibration control10.1088/0964-1726/15/1/N01 ↗
14. Modeling active vibration control of a geared rotor system10.1088/0964-1726/13/3/001 ↗
15. Experimental active vibration control of gear mesh harmonics in a power recirculation gearbox system using a piezoelectric stack actuator10.1088/0964-1726/14/5/028 ↗
16. Application of multichannel active vibration control in a multistage gear transmission system10.1155/2022/9970106 ↗
17. Experimental analysis of an active vibration frequency control in gearbox10.1155/2018/1402697 ↗
18. Multi-stage gear vibration active control based on AFPID control
19. Experimental study on vibration control of spur geared rotor system with active magnetic bearings10.1016/j.jsv.2022.117005 ↗
20. Vibration control of spur geared rotor systems with transmission errors by active magnetic bearings
21. An investigation into vibration control of gear bearing systems10.24425/ame.2021.138401 ↗
22. Experimental identification of high-frequency gear mesh vibrations in a planetary gearbox
23. Active control of planetary gearbox vibration using phase-exact and narrowband simultaneous equations adaptation without explicitly identified secondary path models10.1016/j.ymssp.2018.10.030 ↗
24. Phase-exact adaptive feedforward control with reduced computational complexity for modulated gear mesh vibration at 4.7 khz
25. Piezoelektrische inertialmassenaktoren zur aktiven schwingungsreduktion von zahneingriffsschwingungen im kilohertzbereich
26. Hybrid active suspension system of a helicopter main gearbox10.1177/1077546316655707 ↗
27. Development of a high-performance low-weight hydraulic damper for active vibration control of the main rotor on helicopters-part 2: preliminary experimental validation10.3390/aerospace10100868 ↗
28. Fuzzy algorithm-based active control method for vibration of a mechanical gear transmission system10.21595/jve.2024.23595 ↗
29. Schwingungsbeeinflussung geometrisch komplexer Strukturen mittels piezoelektrischer Flächenwandler am Beispiel des Getriebeheulens
30. Application of active vibration control on single stage spur gear10.1088/1757-899X/1123/1/012049 ↗
31. Robust nvh engineering using experimental methods - source characterization techniques for component transfer path analysis and virtual acoustic prototyping10.4271/2019-01-1542 ↗
32. Active structural acoustic control of gear-box systems using a pair of piezo-based rotating inertial actuators
33. Experimental study on active structural acoustic control of rotating machinery using rotating piezo-based inertial actuators10.1016/j.jsv.2015.03.013 ↗
34. Design and test of a piezoelectric inertial mass actuator for active vibration control
35. An inertial bipedal piezoelectric actuator with integration of triple actuation modes10.1088/1361-665X/ac993b ↗
36. An inertial piezoelectric actuator with small structure but large loading capacity10.1063/5.0053807 ↗
37. Resonant-type piezoelectric inertial drive mechanism with asymmetric inertial masses10.1063/5.0030775 ↗
38. A low frequency magnetostrictive inertial actuator for vibration control10.1016/j.sna.2012.03.015 ↗
39. Experimental verification of model-free active vibration control approach using virtually controlled object10.1177/1077546320902348 ↗
40. Novel dielectric stack actuators for dynamic applications
41. Active vibration isolation with a dielectric elastomer stack actuator10.1088/1361-665X/aa67cb ↗
42. An actuator with tuneable resonant frequency for active vibration damping10.1177/1045389X221132553 ↗
43. Design of a maglev inertial actuator with high mass power ratio for lateral vibration control of propulsion shafting10.3390/act10120315 ↗
44. Active nonlinear control of a stroke limited inertial actuator: theory and experiment10.1016/j.jsv.2019.115009 ↗
45. Identification and analysis of nonlinear dynamics of inertial actuators10.1016/j.ymssp.2018.05.044 ↗
46. LIVE-I: Lightening and Innovating transmission for improving Vehicle Environmental Impacts · 2019
47. Beitrag zur Prädiktion von Schalltransferpfaden in Fahrzeuggetrieben
48. Experimental vibro-acoustic analysis of gearbox behavior using piezoelectric stack actuator excitation
49. Institut für Mechatronische Systeme – TU Darmstadt · 2019
50. Macro fiber composites - overview
51. An investigation into the performance of macro-fiber composites for sensing and structural vibration applications10.1016/S0888-3270(03)00081-5 ↗
52. Teensy 4.1, 7/21/2023
53. Derivation of sensor-actuator layout for active control of gearbox housing vibration
54. Preloading piezoelectric stack actuators in high-speed nanopositioning systems10.3389/fmech.2016.00008 ↗
55. Optimal sensor and actuator placement in complex dynamical networks