journal article·2017-05-01

Characterization the microstructure of pulsed Nd:YAG welding method in low frequencies; correlation with tensile and fracture behavior in laser-welded nitinol joints

Ali Shojaei Zoeram, Aida Rahmani, Seyed Ali Asghar Akbari Mousavi

Smart Materials and Structures· Volume 26· Issue 5
Publisher page

Abstract

Abstract The precise controllability of heat input in pulsed Nd:YAG welding method provided by two additional parameters, frequency and pulse duration, has made this method very promising for welding of alloys sensitive to heat input. The poor weldability of Ti-rich nitinol as a result of the formation of Ti 2 Ni IMC has deprived us of the unique properties of this alloy. In this study, to intensify solidification rate during welding of Ti-rich nitinol, pulsed Nd:YAG laser beam in low frequency was employed in addition to the employment of a copper substrate. Specific microstructure produced in this condition was characterized and the effects of this microstructure on tensile and fracture behavior of samples welded by two different procedures, full penetration and double-sided method with halved penetration depth for each side were investigated. The investigations revealed although the combination of low frequencies, the use of a high thermal conductor substrate and double-sided method eliminated intergranular fracture and increased tensile strength, the particular microstructure, built in the pulsed welding method in low frequencies, results to the formation of the longitudinal cracks during the first stages of tensile test at weld centerline. This degrades tensile strength of welded samples compared to base metal. The results showed samples welded in double-sided method performed much better than samples welded in full penetration mode.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Welding Techniques and Residual Stresses · Laser and Thermal Forming Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

University of Tehran

Imam Khomeini International University

References (21)

Show source-provided references
1. Janaki Rama · J. Mater. Process. Technol. · 2005 · 167 · 7310.1016/j.jmatprotec.2004.09.081 ↗
2. Akbari Mousavi · J. Mater. Process. Technol. · 2010 · 210 · 147210.1016/j.jmatprotec.2010.04.005 ↗
3. Gao · J. Mater. Process. Technol. · 2014 · 214 · 131610.1016/j.jmatprotec.2014.01.015 ↗
4. Falvo · Smart. Mater. Struct. · 2007 · 16 · 77110.1088/0964-1726/16/3/026 ↗
5. Bhagyaraj · J. Alloys Compd. · 2013 · 581 · 34410.1016/j.jallcom.2013.07.046 ↗
6. Schloßmacher · 1997 · 137
7. Shojaei Zoeram · Weld. World · 2016 · 60 · 1110.1007/s40194-015-0281-9 ↗
8. Pardal · Int. J. Adv. Manuf. Technol. · 2016 · 86 · 113910.1007/s00170-015-8110-2 ↗
9. Borrisutthekul · Mater. Sci. Eng. A · 2007 · 467 · 10810.1016/j.msea.2007.03.049 ↗
10. Tzeng · J. Adv. Manuf. Technol. · 2000 · 16 · 1010.1007/PL00013126 ↗
11. Shojaei Zoeram · Mater. Des. · 2014 · 61 · 18510.1016/j.matdes.2014.04.078 ↗
12. Roy · J. Appl. Phys. · 2006 · 10010.1063/1.2214392 ↗
13. Kou · 2003
14. Yang · Mater. Des. · 2014 · 57 · 2110.1016/j.matdes.2013.12.039 ↗
15. Ogata · Mater. Trans. · 2004 · 45 · 107010.2320/matertrans.45.1070 ↗
16. Wang · Int. J. Solid. Struct. · 2009 · 46 · 55710.1016/j.ijsolstr.2008.09.007 ↗
17. Miranda · Int. J. Adv. Manuf. Technol. · 2015 · 81 · 153310.1007/s00170-015-7307-8 ↗
18. Khan · Mater. Trans. · 2008 · 49 · 270210.2320/matertrans.MRA2008243 ↗
19. Trepczyńska-Łent · Arch. Foundry Eng. · 2015 · 15 · 7110.1515/afe-2015-0063 ↗
20. Hutchinson · J. Mech. Phys. Solids · 1968 · 16 · 33710.1016/0022-5096(68)90021-5 ↗
21. Gall · Int. J. Fract. · 2001 · 109 · 18910.1023/A:1011069204123 ↗