journal article·2025-08-22

Reliability analysis based on modeling of POP packages under thermal-drop impact loads

Xuexia Yang, Yanxi Sun, Miao Zhu, Chao Wang, Erqiang Liu, Gesheng Xiao

Publisher page

Abstract

Purpose Portable electronic products are often subjected to fumble and fall during use. The purpose of this study is to investigate the reliability of the chip power temperature loads while being subjected to drop impact loads. Design/methodology/approach In this study, the influence of five different chip power sizes on the Sn0.3Ag0.5Cu (SAC305) solder joints in Package-on-Package (POP) structures under thermal-drop impact load is systematically investigated. The board-level POP package structure is modeled using finite element analysis software COMSOL, and the temperature distribution within the structure is simulated by applying thermal power loads. This temperature field serves as the boundary condition for subsequent analyses, while the drop impact load is applied through the Input-G method. As a result, the stress distribution of the solder joints in the POP packages under thermal-drop impact loading is determined. Furthermore, the relationship between the maximum peeling stress of the solder joints and the maximum number of drops is established based on the power law principle. Finally, the life prediction of critical solder joints is achieved. Findings The findings reveal that solder joint 3 of the U2A component in the POP package is the most critical solder joint, with its stress level being a key determinant of the package’s vulnerability to damage under thermal-drop impact loading conditions. The most pronounced effect on the lifetime of solder joints under thermal-drop impact loading was observed when the chip power ranged from 1 to 1.4 W. It is crucial to consider the influence of power on POP packages under thermal-drop impact loading conditions during electronic design, especially when the power falls within the range of 1–1.4 W. Originality/value The maximum peeling stress of corner solder joint 3 in POP packages can serve as a failure criterion for the optimization of electronic product design. When electronic products incorporating POP packages are subject to handling or are prone to dropping, it is essential to minimize the power to 0 or, to the greatest extent feasible, to limit it to less than 1 W.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Taiyuan University of Science and Technology , Taiyuan,

Taiyuan University of Technology , Taiyuan,

References (28)

Show source-provided references
1. Chen, D.Q. (2016), “Reliability research of stacked packaging (PoP)”, Master’s Thesis, South China University of Technology.
2. Microstructural influences on thermomechanical fatigue behaviour of third generation high Ag content Pb-free solder alloys10.1016/j.jallcom.2016.07.191 ↗
3. Surface finish effect on reliability of SAC 305 soldered chip resistors10.1108/09540911211262520 ↗
4. Phenomenological study of the effect of microstructural evolution on the thermal fatigue resistance of Pb-free solder joints10.1109/TCPMT.2011.2140109 ↗
5. Research on fatigue of TSV-Cu under thermal and vibration coupled load based on numerical analysis10.1016/j.microrel.2020.113590 ↗
6. Effect of thermal treatment on fracture behavior of solder joints at various strain rates: comparison of cyclic and constant temperature10.1016/j.engfailanal.2021.105636 ↗
7. Stress-strain analysis of 3D-TSV interconnect structures based on heat-structure coupling
8. Thermal fatigue failure of micro-solder joints in electronic packaging devices: a review10.3390/ma17102365 ↗
9. Thermal performance and fatigue life prediction of POP stacked chip assembly under thermal cycling load10.1108/MI-09-2019-0058 ↗
10. Thermal cycling effect on the drop reliability of BGA lead-free solder joints10.1108/SSMT-03-2017-0007 ↗
11. Unveiling the damage evolution of SAC305 during fatigue by entropy generation10.1016/j.ijmecsci.2022.108087 ↗
12. An insight into dynamic properties of SAC305 lead-free solder under high strain rates and high temperatures10.1016/j.ijimpeng.2023.104542 ↗
13. Luan, J-e. and Tee, T.Y. (2004), “Novel board level drop test simulation using implicit transient analysis with input-G method”, Paper presented at the Proceedings of 6th Electronics Packaging Technology Conference (EPTC 2004), IEEE, Cat. No. 04EX971.
14. Advanced numerical and experimental techniques for analysis of dynamic responses and solder joint reliability during drop impact10.1109/TCAPT.2006.880455 ↗
15. Niu, X.Y. (2009), “Experimental research and reliability analysis of lead-free solder joints in microelectronic packaging”, Ph.D Dissertation, Taiyuan University of Technology.
16. Rodgers, B., Punch, J. and Jarvis, J. (2002), “Finite element modelling of a BGA package subjected to thermal and power cycling”, Paper presented at the ITherm 2002. Eighth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, Cat. No. 02CH37258.
17. Drop and impact reliability investigation of BGA and LGA interconnects10.1108/SSMT-03-2023-0012 ↗
18. Failure mode and fatigue life analysis of board-level solder joints under coupled temperature and vibration conditions
19. Vandevelde · 2008
20. Thermal–mechanical performance analysis and structure optimization of the TSV in 3-D IC10.1109/TCPMT.2021.3062031 ↗
21. Long-term response of energy piles based on hyperbolic tangent model
22. Quasi-static compression properties and constitutive relations of SAC305 solder
23. Wen, L., Fu, X., Zhou, J., Wang, Q. and Lee, J. (2008), “Dynamic properties testing of solders and modeling of electronic packages subjected to drop impact”, Paper presented at the 2008 International Conference on Electronic Packaging Technology & High Density Packaging.
24. Reliability and failure analysis of SAC 105 and SAC 1205N lead-free solder alloys during drop test events10.1016/j.microrel.2017.12.013 ↗
25. Equilibrium phase diagram design and structural optimization of SAC/Sn-Pb composite structure solder joint for preferable stress distribution10.1016/j.matchar.2023.113389 ↗
26. Reliability analysis of PBGA solder joints under shock load of plate drop
27. Study on the dynamic characteristics of POP package under drop impact load
28. Factors influencing the tough-brittle transition temperature of B50A224 steel