Editorial
Source abstract
Abstract
This and the previous issue of the Journal are dedicated to the Italian Association for Stress Analysis (AIAS). Founded in 1971, the Association gathers together researches from academia, research centres and industries devoted to the investigation on experimental mechanics and stress analysis in general. The activities of the Association and the interaction with national and international research institutions and companies are promoted by the members through a series of working groups on specific areas (Bioengineering, Civil Engineering, Composite Materials, Joining techniques, Residual stresses, Vehicle design). The issues collect some works representative of the activity of the Association in the field of experimental mechanics, selected by the AIAS Executive Committee from those presented during the XXXVII AIAS National Conference, held at University La Sapienza in Rome – September 2008. After the conference, authors were asked to prepare an extended paper which was submitted to the usual peer review process of the Journal. Subjects covered by the papers presented in the two issues are: stress and strain assessment, testing procedures, material characterisation and modelling, composite materials, even for civil applications, and analysis of the in-service loading conditions. This issue contains eight papers. The first paper, presented by Alfano et al., deals with the assessment of the mechanical properties of air plasma-sprayed ceria–yttria co-stabilized zirconia coatings. XRD is adopted for phase analysis of powders and as-sprayed coatings. SEM and image analysis are employed to explore coating microstructure and porosity. Finally, the Young’s modulus of the coating is determined using nanoindentation and a resonant method. The results obtained are then discussed and a cross-check on their consistency is made by using a micromechanical model. Zucchelli et al. discuss the instability of thin plates under transverse loading. The paper compares experimental tests on steel and enamelled steel plates and the results obtained by a non linear numerical model taking into account residual stresses. It is shown that the presence of residual stresses causes an increment of the values of force and work at which the instability takes place. The combined effect of notches and fibre orientation on static and fatigue strength of short glass fibre reinforced polyamide is investigated by Bernasconi et al. by testing injection moulded notched specimens. Synchrotron light microtomography is used for visualisation of local fibre orientation at notches and the obtained images of the internal structure are analysed by the Mean Intercept Length parameter. Results are also discussed in light of the full displacement field measured by Digital Image Correlation. Pitarresi and Galietti investigate the thermoelastic signal from carbon fibre-reinforced plastic laminates. A comparison between the theoretical and experimental values of the thermoelastic signal is reported. The influence of the laminate lay-up and the strong mismatch between the thermal expansion coefficients of the polymer matrix and the fibres are investigated analytically by using strain-based and stress-based analytical models. Experimental evidence of some theoretical findings is provided as well, by reporting on tests performed on CFRP tensile samples manufactured from low-crimp unidirectional fabrics. The use of composites for civil applications is discussed in the following two papers. Ascione et al. analyse the static behaviour under service conditions of concrete beams reinforced with GFRP (Glass Fibre-Reinforced Polymer) as well as CFRP (Carbon Fibre-Reinforced Polymer) bars and stirrups. Two different concretes and two different percentages of reinforcement are considered. Comparisons with analytical predictions given by CNR-DT203/2006 are also reported. Olivito and Zuccarello report on the test results of 20 concrete beams reinforced by CFRP bars, without any shear reinforcement, subjected to three-point bending tests. Mid-span deflection, moment-curvature and bar strains were investigated by means of linear inductive displacement transducers, dial gauges and strain gauges directly applied onto CFRP bars. The acoustic emission technique is also used to find out the beams cracking moment and to investigate the damage phenomena occurred inside the beams during the tests. In conclusion, two interesting applications for the measure of in-service loadings are presented. The study by Pellicioli and Petrone is oriented to the experimental strain analysis of a 420 sailboat mast during sailing. The work involves the design, calibration and installation of strain gauge bridges at seven sections of an instrumented mast and at the shrouds, followed by the collection of strain data during simulated laboratory rigging tests and real sailing sessions with medium/strong wind. The final paper by Bettinelli et al. reports on the experimental activity carried out to develop a new on-water data acquisition system suitable for measuring performance in sculling/sweep rowing. The effective components of the forces resulting in the displacement of rowing shells and their application points are identified in a preliminary study. Then, different sensors are designed to gather the different information needed. The accuracy and repeatability of both complete system and sensors developed are checked on the results of several on-water acquisitions. After this brief analysis of the content of the Issue, I would like to thank all the authors for their valuable contributions and the reviewers who carefully verify the quality of the papers and their suitability for the Journal and provided the authors with helpful comments and suggestions. Eventually, even on behalf of the Italian Association for Stress Analysis, I would also like to express my personal gratitude to my Editor in Chief, Professor Emmanuel Gdoutos, for giving the Association the opportunity to publish this Special Issue, for his help during the entire review process and for his continuous encouragement and support during the whole project.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Powder Metallurgy Techniques and Materials · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References
Reference metadata was not supplied for this record.