Increasing the Corrosion Fatigue Resistance of Welded Joints by High-Frequency Mechanical Peening
Source abstract
Abstract
The cyclic life of butt- and T-welded joints in as-welded condition and after strengthening by high-frequency mechanical peening has been studied. The welded joint specimens were made from a 12 mm thick rolled sheet of commonly used weathering steels 10KhSND and 15KhSND. The fatigue tests were carried out in air and in a corrosive medium (in a 3% NaCl solution) under pulsating tension with a frequency of 5 Hz. It has been found that high-frequency mechanical peening as a method for the plastic surface deformation of the joint metal near the fatigue damage localization sites increases the cyclic life of welded joints in air by a factor of over 10. It has been confirmed that in tests in a corrosive medium, the short-time fatigue strength of welded joints both in initial and in strengthened condition decreases. It has been shown that as a result of strengthening by high-frequency peening, the corrosion fatigue resistance characteristics of butt-welded joints of 15KhSND steel are significantly improved: the cyclic life increases by a factor of 4–10 depending on the level of applied stresses, the short-time fatigue strength, based on 2 · 106 cycles, increases by 85%. It has been found experimentally that in a 3% NaCl solution, strengthening increases the cyclic life of T-welded joints of 15KhSND and 10KhSND steels by a factor of 4–10 and 3.5–4, respectively, and that the short-time fatigue strength, based on 2 · 106 cycles, increases by 114 and 80%, respectively. Most strengthened specimens failed in the base metal, far from the fusion line; the unstrengthened specimens failed only in the transition area between the weld metal and base metal.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Surface Treatment and Residual Stress · Material Properties and Failure Mechanisms · Engineering Diagnostics and Reliability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (9)
Show source-provided references
1. V. D. Gorbach and V. S. Mikhailov, “Surface strengthening of welded joints to increase the corrosion fatigue life of ship structures,” Sudostroenie, No. 4, 45–48 (2000).
2. E. V. Kolomiitsev, “Corrosion fatigue strength of T-joints of 12Kh18N10T steel and methods to increase it,” Avtomat. Svarka, No. 12, 41–43 (2012).
3. R. Baptista, V. Infante, and C. M. Branco, “Study of the fatigue behavior in welded joints of stainless steels treated by weld toe grinding and subjected to salt water corrosion,” Int. J. Fatigue, 30, No. 3, 453–462 (2008).10.1016/j.ijfatigue.2007.04.011 ↗
4. M. Mhaede, “Influence of surface treatments on surface layer properties, fatigue and corrosion fatigue performance of AA7075 T73,” Mater. Design, 41, 61–66 (2012).10.1016/j.matdes.2012.04.056 ↗
5. B. N. Mordyuk, O. P. Karasevskaya, G. I. Prokopenko, and N. I. Khripta, “Ultrafine- grained textured surface layer on Zr–1%Nb alloy produced by ultrasonic impact peening for enhanced corrosion resistance,” Surf. Coat. Tech., 210, 54–61 (2012).10.1016/j.surfcoat.2012.08.063 ↗
6. Z. Dong, Z. Liu, M. Li, et al., “Effect of ultrasonic impact peening on the corrosion of ferritic-martensitic steels in supercritical water,” J. Nucl. Mater., 457, 266–272 (2015).10.1016/j.jnucmat.2014.11.028 ↗
7. M. Daavary and S. A. Sadough Vanini, “Corrosion fatigue enhancement of welded steel pipes by ultrasonic impact treatment,” Mater. Lett., 139, 462–466 (2015).10.1016/j.matlet.2014.10.141 ↗
8. G. I. Prokopenko, B. N. Mordyuk, V. V. Knysh, et al., “Increasing the fatigue resistance and corrosion resistance of welded joints by ultrasonic impact treatment and electric discharge alloying,” Tekhn. Diagn. Nerazrush. Kontr., No. 3, 34–40 (2014).
9. V. A. Degtyarev, “Procedure of evaluation of endurance limit for welded joints with different width after high-frequency mechanical peening,” Strength Mater., 47, No. 4, 595–601 (2015).10.1007/s11223-015-9695-2 ↗