Fracture Resistance of Ceramics: Edge Fracture Method
Source abstract
Abstract
Fracture resistance of macrohomogeneous linear elastic yttria, scandia, alumina, zirconia, and silicon nitride ceramics was studied upon flaking of the edges of rectangular specimens with the Rockwell indenter. The correlation between the obtained estimates and fracture toughness test results gained by the single-edge V-notched beam method was demonstrated. Loads giving rise to the flaking of a part of the edge and distances from this edge to the chip scar on the specimen surface were measured. The ratio of those values was considered as a flaking toughness characteristic. The data obtained were statististically reliable (based on more than a hundred determinations). This procedure termed the edge fracture method can be used along with other known fracture toughness test methods for ceramics, its application is especially advantageous when ceramic item sizes are comparable with those of the standard specimens or when expensive materials (e.g., nanoceramics) are tested.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Thermal properties of materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. G. Ficker, “Zur Frage der Verwendbarkeit keramischer Werkstoffe fur hochtemperaturbeanspruchte Maschinenbautelle,” Ber. DKG VDEfa, 29, 310–324 (1952).
2. G. A. Gogotsi, “Fracture toughness studies on ceramics and ceramic particulate composites at different temperature,” in: J. A. Salem, G. D. Quinn, and M. G. Jenkins (Eds.), Fracture Resistance Testing of Monolithic and Composite Brittle Materials, ASTM STP 1409, American Society for Testing and Materials, Pennsylvania (2002), pp. 76–92.
3. G. A. Gogotsi, “Fracture toughness of advanced ceramics and ceramic composites: SEVNB method,” Poroshk. Metallurg., No. 7/8, 54–67 (2004).
4. ASTM C1421-99. Standard Test Method for the Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature (Annual Book of ASTM Standards), Philadelphia (1999).
5. CEN/TS 14425-5:2004. Advanced Technical Ceramics-Test Methods for Determination of Fracture Toughness of Monolithic Ceramics. Part 5: Single-Edge V-Notch Beam (SEVNB) Method, CEN, Brussels (2004).
6. ISO/DIS 15732. Fine Ceramics (Advanced Ceramics, Advanced Technical Ceramics)-Test Method for Fracture Toughness at Room Temperature by Single-Edge Precracked Beam (SEPB) Method, International Organization for Standardization (1998).
7. T. L. Anderson, Fracture Mechanics, in: Fundamental and Application, CRS Press (1995).
8. G. A. Gogotsi, “Deformation behavior of ceramics,” J. Eur. Ceram. Soc., No. 2, 87–92 (1991).
9. E. Almond and N. McCormick, “Constant geometry edge flaking of brittle materials,” Nature, 321, 53–55 (1986).10.1038/321053a0 ↗
10. N. McCormick and E. Almond, “Edge flaking of brittle materials,” J. Hard Mater., 1, No.1, 25–51 (1990).
11. G. A. Gogotsi, S. P. Mudrik, and A. Rendtel, “Sensitivity of silicon carbide and other ceramics to edge fracture: method and results,” in: E. Lara-Curzio and M. Readey (Eds.), 28th Int. Conf. Advanced Ceramics and Composites, Vol. 25, CESP (2004).10.1002/9780470291191.ch37 ↗
12. J. Kubler, Fracture Toughness of Ceramics Using the SEVNB Method: Round Robin, VAMAS Report No. 37, ESIS Document D2-99, EMPA, Dubendorf (1999).
13. R. Morrell and A. Gant, “Edge chipping-what does it tell us?” in: J. R. Varuer and G. D. Quinn (Eds.), Fractography of Glasses and Ceramics IV, American Ceramic Society, Westerville (2001), 122, p. 23.
14. M. Hang, R. Danzer, and R. Paar, “Edge toughness of brittle materials,” in: G. N. Babini, M. Haviar, and P. Saigalik (Eds.), Engineering Ceramics '96: Higher Reliability, Kluwer Academic Publishers (1997), pp. 327–335.
15. J. Quinn and I. Lloyd, “Flake and scratch size ratios in ceramics,” in: J. R. Varuer and G. D. Quinn (Eds.), Fractography of Glasses and Ceramics IV, American Ceramic Society, Westerville (2001), 122, pp. 57–72.
16. F. Petit, P. Descamps, J. P. Erauw, and F. Cambier, “Toughness (K Ic ) measurement by a sliding indentation method,” Key Eng. Mater., 206–213, 629–632 (1992).
17. G. A. Gogotsi and S. P. Mudrik, “Fracture resistance of ceramics upon edge chipping,” Strength Mater., 36, No.5, 545–547 (2004).10.1023/B:STOM.0000048406.95349.ca ↗
18. R. J. Primas and R. Gstrein (Eds.), ESIS TC 6 Round Robin on Fracture Toughness, EMPA, Dubendorf (1995).
19. G. A. Gogotsi, “Thermal stress behavior of yttria, scandia and AIN ceramics,” Ceram. Int., 6, No.1, 31–35 (1980).10.1016/0390-5519(80)90030-7 ↗
20. A. K. Mitropol'skii, Methods of Statistical Calculations [in Russian], Nauka, Moscow (1971).