Construction and Verification of the Constitutive Model of Pure Copper Deformation at Elevated Temperatures
Source abstract
Abstract
The deformation behavior of pure copper was studied in hot compression tests in the temperature range of 773–1173 K and strain rate interval of 0.001–1.0 s–1, the corresponding flow stress curves were plotted. The new method to calculate critical and saturation stresses was devised, quantitative analysis of strain hardening and dynamic softening was presented, a three-stage constitutive model was constructed to predict the flow stress of pure copper. As predicted and measured flow stress comparison indicate, the physical constitutive model can accurately characterize hot deformation of pure copper. With dynamic recovery and/or recrystallization. Numerical simulation of an upsetting process is carried out by implementing the constitutive model into commercial software. This model can be put to practical use and be quite promising for improving efficiency of a hot forging process for pure copper components.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. M. Hörnqvist, N. Mortazavi, M. Halvarsson, et al., “Deformation and texture evolution of OFHC copper during dynamic tensile extrusion,” Acta Mater., 89, 163–180 (2015).10.1016/j.actamat.2015.01.053 ↗
2. W. H. Tian, A. L. Fan, H. Y. Gao, et al., “Comparison of microstructures in electroformed copper liners of shaped charges before and after plastic deformation at different strain rates,” Mater. Sci. Eng. A, 350, 160–167 (2003).10.1016/S0921-5093(02)00721-9 ↗
3. R. Bobbili, B. V. Ramudu, and V. Madhu, “A physically-based constitutive model for hot deformation of Ti-10-2-3 alloy,” J. Alloy. Compd., 696, 295–303 (2017).10.1016/j.jallcom.2016.11.208 ↗
4. X. C. Li, L. L. Duan, J. W. Li, and X. C. Wu, “Experimental study and numerical simulation of dynamic recrystallization behavior of a micro-alloyed plastic mold steel,” Mater. Design, 66, 309–320 (2015).10.1016/j.matdes.2014.10.076 ↗
5. C. Zhang, L. W. Zhang, W. F. Shen, et al., “Study on constitutive modeling and processing maps for hot deformation of medium carbon Cr–Ni–Mo alloyed steel,” Mater. Design, 90, 804–814 (2016).10.1016/j.matdes.2015.11.036 ↗
6. G. L. Ji, Q. Li, K. Y. Ding, et al., “A physically-based constitutive model for high temperature deformation of Cu-0.36Cr-0.03Zr alloy,” J. Alloy. Compd., 648, 397–407 (2015).10.1016/j.jallcom.2015.06.264 ↗
7. M. S. Chen, Y. C. Lin, K. K. Li, et al., “A new method to establish dynamic recrystallization kinetics model of a typical solution-treated Ni-based superalloy,” Comput. Mater. Sci., 122, 150–158 (2016).10.1016/j.commatsci.2016.05.016 ↗
8. D. Feng, X. M. Zhang, S. D. Liu, et al., “Constitutive equation and hot deformation behavior of homogenized Al–7.68Zn–2.12Mg–1.98Cu–0.12Zr alloy during compression at elevated temperature,” Mater. Sci. Eng. A, 608, 63–72 (2014).10.1016/j.msea.2014.04.055 ↗
9. R. H. Zhu, Q. Liu, J. F. Li, et al., “Dynamic restoration mechanism and physically based constitutive model of 2050 Al-Li alloy during hot compression,” J. Alloy. Compd., 650, 75–85 (2015).10.1016/j.jallcom.2015.07.182 ↗
10. H. Matsumoto and V. Velay, “Mesoscale modeling of dynamic recrystallization behavior, grain size evolution, dislocation density, processing map characteristic, and room temperature strength of Ti-6Al-4V alloy forged in the (α + β) region,” J. Alloy. Compd., 708, 404–413 (2017).10.1016/j.jallcom.2017.02.285 ↗
11. I. Mejia, F. Reyes-Calderon, and J. M. Cabrera, “Modeling the hot flow behavior of a Fe–22Mn–0.41C–1.6Al–1.4Si TWIP steel microalloyed with Ti, V and Nb,” Mater. Sci. Eng. A, 644, 374–385 (2015).10.1016/j.msea.2015.07.078 ↗
12. N. Haghdadi, D. Martin, and P. Hodgson, “Physically-based constitutive modelling of hot deformation behavior in a LDX 2101 duplex stainless steel,” Mater. Design, 106, 420–427 (2016).10.1016/j.matdes.2016.05.118 ↗
13. K. Tan, J. Li, Z. J. Guan, et al., “The identification of dynamic recrystallization and constitutive modeling during hot deformation of Ti55511 titanium alloy,” Mater. Design, 84, 204–211 (2015).10.1016/j.matdes.2015.06.093 ↗
14. T. Mirzaie, H. Mirzadeh, and J. M. Cabrera, “A simple Zerilli–Armstrong constitutive equation for modeling and prediction of hot deformation flow stress of steels,” Mech. Mater., 94, 38–45 (2016).10.1016/j.mechmat.2015.11.013 ↗
15. H. Mirzadeh, “Constitutive modeling and prediction of hot deformation flow stress under dynamic recrystallization conditions,” Mech. Mater., 85, 66–79 (2015).10.1016/j.mechmat.2015.02.014 ↗
16. G. B. Wei, X. D. Peng, A. Hadadzadeh, et al., “Constitutive modeling of Mg–9Li–3Al–2Sr–2Y at elevated temperatures,” Mech. Mater., 89, 241–253 (2015).10.1016/j.mechmat.2015.05.006 ↗