Fabrication and tribological characterization of laser textured boron cast iron surfaces
Source abstract
Abstract
Abstract Laser surface texturing technology was employed for fabricating textured structures on cylinder liners. The tribological behavior of the cylinder liners with different texturing structures including line, dimple and line + dimple and texturing area ratio was investigated under the lubrication of esterified bio-oil with and without MoS 2 microsheets as additives. The experimental results indicated that all the three textured surfaces showed better lubricating effects than untextured one except for the line + dimple structures leading to a higher wear rate to the cylinder liner; the dimple structures have better friction and wear performance than other structures. In addition, the textured surfaces lubricated with esterified bio-oil with MoS 2 microsheets presented the optimal friction reduction and antiwear properties. This might be ascribed to the fact that besides the adsorbed film composed of carbon and organics from the base oil, there was a robust complex composite tribo-film composed of MoS 2 , MoO 3 , FeOOH, FeO, Fe 2 O 3 , FeS, FeSO 4 and etc. on the rubbing surfaces. Furthermore, the dimples acted as an oil reservoir and provided a sink to pull wear debris away from the contacting surfaces. The combined actions of these factors gave rise to the lowest friction and wear of the tribopairs tested. The synergistic combination of the 12% area ratio dimples and MoS 2 microsheets showed great potential for application in IC engines, when coupled with bio-oil to reduce parasitic losses and energy consumption.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tribology and Lubrication Engineering · Lubricants and Their Additives · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Organic light emitting diodes: energy saving lighting technology—a review10.1016/j.rser.2012.02.021 ↗
2. Investigation of the tribology behaviour of the graphene nanosheets as oil additives on textured alloy cast iron surface10.1016/j.apsusc.2016.06.080 ↗
3. Experimental study on effect of micro textured surfaces generated by ultrasonic vibration assisted face turning on friction and wear performance10.1016/j.apsusc.2016.07.064 ↗
4. Influence of boron content on the microstructure and tribological properties of Cr-B-N coatings in water lubrication10.1016/j.apsusc.2016.03.190 ↗
5. Scientific production of renewable energies worldwide: an overview10.1016/j.rser.2012.10.020 ↗
6. Experimental friction evaluation of cylinder liner/piston ring contact10.1016/j.wear.2010.08.028 ↗
7. Modelling the hydrodynamic support of cylinder bore and piston rings with laser textured surfaces10.1016/j.triboint.2012.01.016 ↗
8. Improving tribological behaviour of piston ring–cylinder liner frictional pair by liner surface texturing10.1016/j.triboint.2012.11.027 ↗
9. Research on discriminating partition laser surface micro-texturing technology of engine cylinder10.1016/j.triboint.2016.02.010 ↗
10. Study on influence of cylinder liner surface texture on lubrication performance for cylinder liner–piston ring components10.1007/s11249-013-0141-y ↗
11. Development of the theoretical model for the optimal design of surface texturing on cylinder liner10.1016/j.triboint.2011.12.017 ↗
12. An overview of geometrical parameters of surface texturing for piston/cylinder assembly and mechanical seals10.1007/s11012-015-0180-6 ↗
13. Effect of laser textured dimples on the lubrication performance of cylinder liner in diesel engine10.1002/ls.1185 ↗
14. Improving tribological performance of piston rings by partial surface texturing10.1115/1.1866171 ↗
15. Friction reduction benefits in valve-train system using IF-MoS2 added engine oil10.1080/10402004.2014.960540 ↗
16. Tribological effects of BN and MoS2 nanoparticles added to polyalphaolefin oil in piston skirt/cylinder liner tests10.1007/s11249-012-9965-0 ↗
17. Effect of catalytic esterification on the friction and wear performance of bio-oil10.1016/j.wear.2013.12.029 ↗
18. Synergistic lubricating behaviors of graphene and MoS2 dispersed in esterified bio-oil for steel/steel contact10.1016/j.wear.2015.09.011 ↗
19. MoS2/nitrogen-doped graphene as efficient electrocatalyst for oxygen reduction reaction10.1016/j.electacta.2015.04.044 ↗
20. Morphological influence of molybdenum disulfide on the tribological properties of rapeseed oil10.1007/s11249-012-0092-8 ↗
21. Combined friction and wear reduction in a reciprocating contact through laser surface texturing10.1016/j.wear.2016.03.035 ↗
22. Friction and wear behavior analysis of the stainless steel surface fabricated by laser texturing underwater10.1016/j.triboint.2016.06.001 ↗
23. Optimal topology design of continuum structures with stress concentration alleviation via level set method10.1002/nme.4416 ↗
24. A comparative study on wear behavior and mechanism of styrene butadiene rubber under dry and wet conditions10.1016/j.wear.2016.01.025 ↗
25. Improving tribological properties of titanium alloys by combining laser surface texturing and diamond-like carbon film10.1016/j.triboint.2014.09.017 ↗
26. Shear deformation and grain refinement during accumulative back extrusion of AZ31 magnesium alloy10.1007/s10853-010-5029-8 ↗
27. Raman evidence for a weakened OO bond in mononuclear low-spin iron (III)-hydroperoxides10.1021/ja982812p ↗
28. Synthesis and characterization of hollow MoS2 microspheres grown from MoO3 precursors10.1016/j.jallcom.2010.04.088 ↗
29. Characterization and auto-restoration mechanism of nanoscale serpentine powder as lubricating oil additive under high temperature10.1016/j.triboint.2011.02.001 ↗
30. The effect of annealing temperature on the structure of diamond-like carbon films by electrodeposition technique10.1023/A:1004711913325 ↗
31. Evolution of structure, magnetic and transport properties of sputtered films from Fe to Fe3O410.1088/0022-3727/39/24/002 ↗
32. Influence of microalgal bio-oil on the lubrication properties of engine oil10.2516/ogst/2014050 ↗
33. Enhancing the tribological performance of PEEK exposed to water-lubrication by filling goethite (α-FeOOH) nanoparticles10.1039/C6RA06904E ↗
34. Tribological properties of phenolic resin bonded abrasive tools filled with two inclusion complexes of β-cyclodextrin and sulfur-containing additives10.1177/1350650114527071 ↗
35. Influence of the electrochemical reduction process on the performance of graphene-based capacitors10.1016/j.carbon.2012.08.016 ↗
36. Tribological properties of PTFE/laser surface textured stainless steel under starved oil lubrication10.1016/j.triboint.2014.07.017 ↗
37. Effect of oxidative modification of coal tar pitch-based mesoporous activated carbon on the adsorption of benzothiophene and dibenzothiophene10.1016/j.fuproc.2014.08.022 ↗
38. The integration of sub-10nm gate oxide on MoS2 with ultra low leakage and enhanced mobility
39. JF · 1995