The effect of ultrasonic nanocrystal surface modification on low temperature nitriding of ultra-high strength steel
Source abstract
Abstract
Abstract In this research, a surface plastic deformation layer was induced on 300M ultra-high strength steel using ultrasonic nanocrystal surface modification (UNSM). The UNSM-treated and control specimens were then nitrided at 450 °C for 6 h. After gas nitriding, the microstructure, corrosion and wear resistance of 300M steel with and without UNSM pre-treatment were investigated. After nitriding, the UNSM-treated specimens generated a dense surface nitride layer that was thicker than that of the control specimens. The high defect density and refined lath martensite induced by UNSM were found to accelerate the nitrogen diffusion and efficiency. X-ray diffraction patterns revealed that α-Fe phase occupied the largest proportion in the nitriding layer of specimens without UNSM pre-treatment. However due to the higher nitriding efficiency, the main phase of UNSM-treated specimens after nitriding was found to be e-Fe2-3N. Compared with the specimens without pre-treatment, UNSM-treated specimens exhibited higher surface hardness as well as higher corrosion and wear resistance after nitriding.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Surface Treatment and Residual Stress · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Electrochemical corrosion behavior of 300M ultra high strength steel in chloride containing environment
2. Improvement of the cavitation erosion resistance of an AISI 304L austenitic stainless steel by high temperature gas nitriding10.1016/j.msea.2004.05.003 ↗
3. Corrosion resistance of nitrided layers on austenitic steel10.1016/j.surfcoat.2005.11.099 ↗
4. Excellent enhancement of corrosion properties of Fe-9Al-30Mn-1.8C alloy in 3.5% NaCl and 10% HCl aqueous solutions using gas nitriding treatment10.1016/j.jallcom.2015.01.201 ↗
5. Surface modification by gas nitriding for improving cavitation erosion resistance of CP-Ti10.1016/j.apsusc.2014.01.152 ↗
6. Effects of gas nitriding temperature on the surface properties of a high manganese TWIP steel10.3390/met7030102 ↗
7. Corrosion properties of active screen plasma nitrided 316 austenitic stainless steel10.1016/j.corsci.2003.09.015 ↗
8. Large-scale synthesis of nanostructured nitride layer on Ti plate using mechanical shot peening and low-temperature nitriding10.1002/adem.201700157 ↗
9. Fatigue properties of gas nitrided austenitic stainless steel pre-treated with fine particle peening10.1016/j.ijfatigue.2009.07.019 ↗
10. Low-temperature nitriding of 38CrMoAl steel with a nanostructured surface layer induced by surface mechanical attrition treatment10.1016/j.surfcoat.2008.04.085 ↗
11. The effect of surface mechanical attrition treatment on low temperature plasma nitriding of an austenitic stainless steel10.1016/j.surfcoat.2013.01.047 ↗
12. Effect of SPD surface layer on plasma nitriding of Ti–6Al–4V alloy10.1016/j.msea.2013.09.077 ↗
13. Nitriding iron at lower temperatures10.1126/science.1080216 ↗
14. The effect of surface nanocrystallization on plasma nitriding behaviour of AISI 4140 steel10.1016/j.apsusc.2010.08.004 ↗
15. Nanostructure formation mechanism of α-titanium using SMAT10.1016/j.actamat.2004.05.023 ↗
16. Evolution of texture and microstructure in pulsed electro-deposited Cu treated by Surface Mechanical Attrition Treatment (SMAT)10.1016/j.jallcom.2010.04.040 ↗
17. Bimodal nanocrystallization of NiTi shape memory alloy by laser shock peening and post-deformation annealing10.1016/j.actamat.2011.07.070 ↗
18. Laser shock peening effect on the dislocation transitions and grain refinement of Al-Mg-Si alloy10.1016/j.matchar.2014.08.020 ↗
19. Tensile properties and surface nanocrystallization analyses of H62 brass subjected to room-temperature and warm laser shock peening10.1016/j.jallcom.2016.12.210 ↗
20. Effect of severe shot peening on microstructure and fatigue strength of cast iron10.1016/j.ijfatigue.2013.08.022 ↗
21. Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening10.1016/j.apsusc.2015.05.093 ↗
22. Nanoscale surface modification of AISI 316L stainless steel by severe shot peening10.1016/j.matdes.2016.03.162 ↗
23. Gradient nanostructure and residual stresses induced by ultrasonic nano-crystal surface modification in 304 austenitic stainless steel for high strength and high ductility10.1016/j.msea.2014.06.114 ↗
24. Effect of ultrasonic nanocrystal surface modification on surface and fatigue properties of quenching and tempering S45C steel10.1016/j.apsusc.2014.09.068 ↗
25. Fretting wear and friction reduction of CP titanium and Ti-6Al-4V alloy by ultrasonic nanocrystalline surface modification10.1016/j.surfcoat.2012.06.046 ↗
26. Microstructural evolution and surface properties of nanostructured Cu-based alloy by ultrasonic nanocrystalline surface modification technique10.1016/j.apsusc.2016.01.237 ↗
27. Effects of ultrasonic nanocrystalline surface modification (UNSM) technique on the tribological behavior of sintered cu-based alloy10.1016/j.triboint.2013.12.003 ↗
28. Effects of ultrasonic nanocrystalline surface modification on the tribological properties of AZ91D magnesium alloy10.1016/j.triboint.2012.04.024 ↗
29. Improvement of the fatigue strength of SUS304 austenite stainless steel using ultrasonic nanocrystal surface modification10.1016/j.surfcoat.2012.12.033 ↗
30. Effect of ultrasonic nanocrystal surface modification on residual stress, microstructure and fatigue behavior of ATI 718Plus alloy10.1016/j.msea.2017.11.043 ↗
31. Improving surface finish and wear resistance of additive manufactured nickel-titanium by ultrasonic nano-crystal surface modification10.1016/j.jmatprotec.2017.06.038 ↗
32. The effects of ultrasonic nanocrystal surface modification on the fatigue performance of 3D-printed Ti6410.1016/j.ijfatigue.2017.05.019 ↗
33. Study on the fatigue properties of plasma nitriding S45C with a pre-ultrasonic nanocrystal surface modification process10.1016/j.surfcoat.2012.11.033 ↗
34. Effect of ultrasonic nanocrystal surface modification on the fatigue behaviors of plasma-nitrided S45C steel10.1016/j.surfcoat.2012.10.063 ↗
35. Low-temperature nitriding of nanocrystalline Inconel 718 alloy10.1016/j.surfcoat.2017.09.040 ↗
36. Surface nanocrystallization by ultrasonic nano-crystal surface modification and its effect on gas nitriding of Ti6Al4V alloy10.1016/j.msea.2018.08.089 ↗
37. Effects of ultrasonic nanocrystal surface modification on the thermal oxidation behavior of Ti6Al4V10.1016/j.surfcoat.2017.04.051 ↗
38. Structural characteristics of low-temperature plasma-nitrided layers on AISI 304 stainless steel with an α’-martensite layer10.1016/S0257-8972(01)01670-X ↗
39. Interrogation of the microstructure and residual stress of a nickel-base alloy subjected to surface severe plastic deformation10.1016/j.actamat.2007.10.003 ↗
40. Plasma nitriding of AISI 304 austenitic stainless steel with pre-shot peening10.1016/j.surfcoat.2010.03.018 ↗
41. Changing in fatigue life of 300M bainitic steel after laser carburizing and plasma nitriding10.1051/matecconf/201816521002 ↗
42. Plasma nitriding of steels with severely plastic deformed surfaces10.1007/s10853-012-6566-0 ↗
43. Effects of ultrasonic nanocrystal surface modification on the wear and micropitting behavior of bearing steel in boundary lubricated steel-steel contacts10.1016/j.wear.2017.09.012 ↗
44. Nanocrystalline steel processed by severe rolling of lath martensite10.1016/j.msea.2006.06.047 ↗
45. Microstructure and corrosion resistance of the layers formed on the surface of precipitation hardenable plastic mold steel by plasma-nitriding10.1016/j.apsusc.2009.08.062 ↗
46. Wear resistance of two-phase titanium alloy after deformation-diffusion treatment10.1016/j.triboint.2018.06.011 ↗
47. Effects of shot peening pre-treatment and plasma nitriding parameters on the structural, mechanical and tribological properties of AISI 4140 low-alloy steel10.1016/j.surfcoat.2018.11.043 ↗
48. Dry sliding wear resistance of low temperature plasma carburised austenitic stainless steel10.1016/S0043-1648(02)00170-9 ↗