Optimization of Inconel 718 thick deposits by cold spray processing and annealing
Source abstract
Abstract
Abstract Cold Spraying of high strength materials, i.e., Inconel 718 is still challenging due to the limited deformability of the material restricting the quality of deposits. Thus, process parameters must be tuned for reaching higher particle impact velocities and temperatures to allow for maximum amounts of well-bonded particle-substrate and particle-particle interfaces. In the present study, Inconel 718 powder was cold sprayed under varied process gas temperatures for a systematic study of the influence on the quality of thick deposits. In addition, one set of samples of each batch was exposed to post heat treatment procedures by hot isostatic pressing, thermal soft annealing, and aging for attaining hard bulk material properties. Deposits microstructure, porosity, electrical conductivity, hardness, and residual stress were analyzed in as-sprayed and as-heat treated conditions. Results are discussed in terms of the “coating quality parameter”, defined as the ratio between particle impact velocity and critical velocity. As-sprayed deposits exhibit microstructures with highly deformed particles and well bonded internal interfaces. X-ray diffraction reveals that powder and deposits present a γ-solid-solution phase, allowing to assume conventional softening behavior for estimating critical conditions for bonding. Increasing the process gas temperature leads to lower coating porosity and higher electrical conductivity. Deposits showed similarly high microhardness and compressive residual stresses, both caused by work hardening during cold spraying. Subsequent heat treatments improved the quality of internal interfaces, mostly for deposits with high values of “coating quality parameters”. By distinguishing influences on several coating properties, these results contribute to gain basic knowledge for successful manufacturing of Inconel 718 thick deposits by cold spraying, particularly concerning needed coating quality parameters for adjusting desired properties.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Cold gas dynamic spray additive manufacturing today: deposit possibilities, technological solutions and viable applications10.1016/j.matdes.2017.07.067 ↗
2. Solid-state additive manufacturing and repairing by cold spraying: a review10.1016/j.jmst.2017.09.015 ↗
3. Cold spray additive manufacturing and repair: fundamentals and applications
4. Cold gas dynamic manufacturing: a non-thermal approach to freeform fabrication10.1016/j.ijmachtools.2006.05.001 ↗
5. Potential of cold gas dynamic spray as additive manufacturing technology10.1007/s00170-013-5166-8 ↗
6. An analysis of the cold spray process and its coatings10.1361/105996302770348682 ↗
7. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗
8. Present status and future prospects of cold spraying
9. Development of a generalized parameter window for cold spray deposition10.1016/j.actamat.2005.10.005 ↗
10. On parameter selection in cold spraying10.1007/s11666-011-9662-9 ↗
11. Karthikeyan · 2016
12. Cold spraying of Cu-Al-Bronze for cavitation protection in marine environments
13. Reed · 2008
14. J · 2004 · 1
15. Marrocco · 2008
16. Investigating the cause of hindrance to the interfacial bonding of INCONEL 718 layer deposited by kinetic spray process10.5695/JKISE.2015.48.6.275 ↗
17. Pressureless sintering of cold sprayed Inconel 718 deposit10.1016/j.msea.2012.06.097 ↗
18. Cold spray forming of Inconel 71810.1007/s11666-012-9827-1 ↗
19. Microstructural and mechanical properties of high-performance Inconel 718 alloy by cold spraying10.1016/j.jallcom.2019.04.045 ↗
20. Cold spray deposition of freestanding Inconel samples and comparative analysis with selective laser melting10.1007/s11666-017-0572-3 ↗
21. Diagnostics of cold-sprayed particle velocities approaching critical deposition conditions10.1007/s11666-017-0596-8 ↗
22. New developments in cold spray based on higher gas and particle temperatures10.1361/105996306X147144 ↗
23. Determination of plastic constitutive properties of microparticles through single particle compression10.1016/j.apt.2015.08.013 ↗
24. From particle acceleration to impact and bonding in cold spraying10.1007/s11666-009-9357-7 ↗
25. ASTM Standard E2109-1 · 2014
26. Kohri · 2016 · vol. 2 · 103
27. Improvement of X-ray stress measurement from a Debye–Scherrer ring by oscillation of the X-ray incident angle10.1017/S0885715615000433 ↗
28. Analysis of thermal history and residual stress in cold-sprayed coatings10.1007/s11666-013-9976-x ↗
29. Residual stress analysis of cold-sprayed copper coatings by numerical simulation10.1007/s11666-015-0308-1 ↗
30. Influence of spraying parameters on cold gas spraying of iron aluminide intermetallics10.1016/j.surfcoat.2014.07.070 ↗
31. Coating formation, fracture mode and cavitation performance of Fe40Al deposited by cold gas spraying10.1179/1743294414Y.0000000420 ↗
32. Mechanical properties of cold-sprayed and thermally sprayed copper coatings10.1016/j.surfcoat.2005.10.007 ↗
33. Microstructures and key properties of cold-sprayed and thermally sprayed copper coatings10.1016/j.surfcoat.2005.05.011 ↗
34. Porosity effect on the electrical conductivity of sintered powder compacts10.1007/s00339-008-4534-y ↗
35. Electrical conductivity and porosity relationship in metal foams10.1007/s10934-008-9248-1 ↗
36. Prediction of thermal conductivity and electrical resistivity of porous metallic materials10.1016/0017-9310(73)90104-X ↗
37. Effect of porosity on the electrical resistivity of carbon materials10.1016/S1872-5805(13)60087-6 ↗
38. Effect of microstructure on electrical conductivity of Inconel 718 alloys10.1179/1743284714Y.0000000638 ↗
39. Identification of Mo-rich M23C6 carbides in alloy 71810.1007/s11661-016-3593-5 ↗
40. Analysis of the residual stress and bonding mechanism in the cold spray technique using experimental and numerical methods10.1016/j.surfcoat.2014.04.059 ↗
41. A review of testing methods for thermal spray coatings10.1179/1743280414Y.0000000029 ↗
42. Role of thermal spray processing method on the microstructure, residual stress and properties of coatings: an integrated study of Ni-5 wt. % Al bond coats10.1016/j.msea.2003.08.023 ↗
43. Residual stress development in cold sprayed Al, Cu and Ti coatings10.1016/j.actamat.2013.06.033 ↗
44. Integrated characterization of cold sprayed aluminum coatings10.1016/j.actamat.2006.09.006 ↗