journal article·2023-12Open access

Tribological and electrochemical performances of HVOF sprayed NbC-NiCr coatings

Larissa Rossi Gehlen, Giovanni Bolelli, Pietro Puddu, Enrico Forlin, Alberto Colella, Giuseppe Pintaude, Luca Lusvarghi

Abstract

A wide range of mechanical parts are protected against wear and corrosion by thermally sprayed WC- or Cr3C2-based hardmetals. However, little is known about the potential of other hardmetal coating formulations. Since promising results were obtained with bulk NbC-based hardmetal cutting tools, in this work we investigated NbC-based coatings, which have not been reported yet in the literature. NbC particles were homogeneously dispersed with volume fractions of 25 % and 40 % in a Ni-20wt.%Cr matrix by mechanical alloying, and the resulting powders were sprayed onto stainless steel substrates by the High-Velocity Oxygen Fuel (HVOF) process. Irrespective of the process parameters, the coatings exhibit low porosity (<1 vol%) and hardness values of about 900 HV0.3 (NbC-25NiCr) and 1000 HV0.3 (NbC-40NiCr). The composition with higher amount of NbC phase is less hard because its greater brittleness results in cracking during indentation. The sliding wear resistance of the NbC-based coatings, tested by ball-on-disc tribometry from room temperature up to 600 °C, is generally intermediate between that of WC-CoCr and Cr3C2-NiCr references, and it is usually comparable to that of TiC-NiCr, another type of alternative hardmetal coating, tested in our previous work. Though the NbC-NiCr exhibited limited three-body abrasion resistance due to the occurrence of some brittle fracture together with ductile grooving, they offer a particularly interesting performance at 400 °C, with lower wear rates than Cr3C2-NiCr and TiC-NiCr. Additionally, the NbC-NiCr coatings tested in this work, especially the one with 40 vol% matrix phase, exhibit excellent corrosion resistance. Both corrosion current densities (~0.1 μA/cm2) and passive current densities, (<1 μA/cm2) obtained by electrochemical polarization tests, were lower than the corresponding values found for all reference coatings (WC-CoCr, Cr3C2-NiCr and TiC-NiCr), Thus, the NbC-NiCr coatings are promising for applications where a good balance between corrosion resistance and wear resistance over a range of temperatures is required.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. High-temperature sliding wear of metals10.1016/S0301-679X(02)00041-5 ↗
2. Tribological, thermal and mechanical coupling aspects of the dry sliding contact10.1016/j.triboint.2006.08.004 ↗
3. Tribo-corrosion of coatings: a review10.1088/0022-3727/40/18/S10 ↗
4. Coatings tribology—contact mechanisms and surface design10.1016/S0301-679X(98)00013-9 ↗
5. Application of hardmetals as thermal spray coatings10.1016/j.ijrmhm.2014.09.029 ↗
6. History of hardmetals
7. Fundamentals and general applications of hardmetals
8. Cemented tungsten carbide hardmetal - an introduction
9. Wear-resistant coatings
10. Refining the understanding of China’s tungsten dominance with dynamic material cycle analysis10.1016/j.resconrec.2020.104829 ↗
11. Identifying supply risks by mapping the cobalt supply chain10.1016/j.resconrec.2020.104743 ↗
12. Cemented carbide phase diagrams: a review10.1016/j.ijrmhm.2011.02.004 ↗
13. An assessment of the Fe-Ni-W-C phase diagram10.1515/ijmr-1987-780301 ↗
14. Phases and Equilibria in the W–C and W–Co–C systems
15. Development and application of WC-based alloys bonded with alternative binder phase10.1080/10408436.2018.1483320 ↗
16. Comparison of self-mated hardmetal coatings under dry sliding conditions up to 600°C10.1016/j.wear.2008.04.013 ↗
17. Comparative study of thermally sprayed coatings under different types of wear conditions for hard chromium replacement10.1007/s11249-011-9791-9 ↗
18. Hard but slippery - titanium hardmetal coatings have industrial potential10.1016/S0026-0657(05)70410-0 ↗
19. Dry sliding up to 7.5m/s and 800°C of thermally sprayed coatings of the TiO2–Cr2O3 system and (Ti,Mo)(C,N)–Ni(Co)10.1016/j.wear.2008.12.105 ↗
20. Application of TiC reinforced Fe-based coatings by means of high velocity air fuel spraying10.1088/1757-899X/181/1/012014 ↗
21. Investigation of properties and wear behavior of HVOF sprayed TiC-strengthened Fe coatings10.1007/s11666-009-9384-4 ↗
22. TiC–NiCr thermal spray coatings as an alternative to WC-CoCr and Cr3C2–NiCr
23. Corrosion and wear performances of alternative TiC-based thermal spray coatings10.1016/j.surfcoat.2022.128400 ↗
24. High-temperature sliding wear, elastic modulus and transverse rupture strength of Ni bonded NbC and WC cermets10.1016/j.ijrmhm.2019.105143 ↗
25. Potentials of niobium carbide (NbC) as cutting tools and for wear protection10.1016/j.ijrmhm.2018.01.009 ↗
26. Substitution of commercially coated tungsten carbide tools in dry cylindrical turning process by HiPIMS coated niobium carbide cutting inserts10.1016/j.surfcoat.2018.07.105 ↗
27. Tribology of HVOF- and HVAF-sprayed WC–10Co4Cr hardmetal coatings: a comparative assessment10.1016/j.surfcoat.2015.01.048 ↗
28. Grohol · 2023
29. C.E.L. Latunussa, K. Georgitzikis, C.T. de Matos, M. Grohol, U. Eynard, D. Wittmer, L. Mancini, M. Unguru, C. Pavel, S. Carrara, F. Mathieux, D. Pennington, G.A. Blengini, Study on the EU's List of Critical Raw Materials (2020), Factsheets on Critical Raw Materials, Luxembourg, 2020. doi:https://doi.org/10.2873/92480.
30. Niobium carbide for wear protection – tailoring its properties by processing and stoichiometry10.1016/j.mprp.2015.12.010 ↗
31. Improvement of corrosion resistance for gray cast iron in palm biodiesel application using thermoreactive diffusion Niobium Carbide (NbC) coating10.3390/coatings8060216 ↗
32. Rettig · 2023
33. Properties of HVOF-sprayed TiC-FeCrAl coatings10.1016/j.wear.2018.11.002 ↗
34. Alternative metallic matrices for WC-based HVOF coatings10.1016/j.surfcoat.2020.126308 ↗
35. Metallic materials — Instrumented indentation test for hardness and materials parameters — part 1: test method
36. High temperature mechanical properties of WC–Co hard metals10.1016/j.ijrmhm.2016.01.002 ↗
37. Young’s Modulus of various refractory materials as a function of temperature10.1111/j.1151-2916.1959.tb15462.x ↗
38. Investigating load-dependent wear behavior and degradation mechanisms in Cr3C2–NiCr coatings deposited by HVAF and HVOF10.1016/j.jmrt.2021.10.088 ↗
39. Gelation-based feed-stock technologies for HVOF thermal spray development: Micro-composite powder preparation and HVOF coating microstructure10.1016/j.surfcoat.2022.129089 ↗
40. Utilization of ball-milled powders for surface protective coating
41. Effect of HVOF processing parameters on Cr3C2-NiCr hard coatings deposited on AISI 4140 steel
42. Effects of internal oxide contents on the oxidation and β-phase depletion behaviour in HOVF CoNiCrAlY coatings10.1016/j.surfcoat.2021.127666 ↗
43. Mechanisms of oxidation and its role in microstructural evolution of metallic thermal spray coatings - case study for Ni-Al10.1016/j.surfcoat.2005.07.072 ↗
44. Dominant effect of carbide rebounding on the carbon loss during high velocity oxy-fuel spraying of Cr3C2-NiCr10.1016/S0040-6090(02)00708-3 ↗
45. The influence of heat treatment on tribological and mechanical properties of HVOF sprayed CrC–NiCr coatings10.1007/s12289-009-0466-0 ↗
46. Effects of HVOF spray parameters on porosity and hardness of 316L SS coated Mg AZ80 alloy10.1016/j.surfcoat.2022.128898 ↗
47. Process characteristics, particle behavior and coating properties during HVOF spraying of conventional, fine and nanostructured WC-12Co powders10.1016/j.surfcoat.2020.126716 ↗
48. The Wear coefficient—magnitude, scatter, uses10.1115/1.3251624 ↗
49. Straffelini · 2015 · 21
50. Structural properties and Raman spectra of columbite-type NiNb2−xVxO6 synthesized under high pressure10.1016/j.jssc.2020.121607 ↗
51. Highly nonlinear Pb2P2O7-Nb2O5 glasses for optical fiber production10.1016/j.jnoncrysol.2016.04.019 ↗
52. Infrared and Raman study of WO3 tungsten trioxides and WO3·xH2O tungsten trioxide tydrates10.1016/0022-4596(87)90359-8 ↗
53. Densification and tribological profile of niobium oxide10.1016/j.wear.2016.02.003 ↗
54. Friction and wear of binder-less niobium carbide10.1016/j.wear.2013.07.013 ↗
55. Composition, structure and properties of the oxide films formed on the stainless steel 316L in a primary type PWR environment10.1016/S0010-938X(97)00158-3 ↗
56. The use of niobium carbide (NbC) as cutting tools and for wear resistant tribosystems10.1016/j.ijrmhm.2014.07.002 ↗
57. The tribological and mechanical properties of niobium carbides (NbC) bonded with cobalt or Fe3Al10.1016/j.wear.2014.09.007 ↗
58. Sliding and abrasive wear behaviour of HVOF- and HVAF-sprayed Cr3C2–NiCr hardmetal coatings10.1016/j.wear.2016.03.034 ↗
59. Abrasive wear behaviour of WC-CoCr and Cr3C2-20(NiCr) deposited by HVOF and detonation spray processes10.1016/j.surfcoat.2004.10.136 ↗
60. Corrosion behavior and galvanic corrosion resistance of WC and Cr3C2 cermet coatings in Madeira River Water10.1007/s11666-021-01152-8 ↗
61. Thermally-sprayed WC-based cermet coatings for corrosion resistance applications10.1007/s11837-018-3131-6 ↗
62. Corrosion properties of co-based cemented carbides in acidic solutions10.1016/S0263-4368(03)00027-1 ↗
63. Microstructure and mechanical properties of NbC-matrix hardmetals with secondary carbide addition and different metal binders10.1016/j.ijrmhm.2014.10.014 ↗
64. Microstructure and mechanical properties of NbC matrix cermets using Ni containing metal binder10.1016/j.mprp.2016.05.009 ↗
65. Effect of carbon content on the microstructure and mechanical properties of NbC-Ni based cermets10.3390/met8030178 ↗