journal article·2024-10Open access

Friction and wear characteristics of DLC-terminated coatings deposited on AlSi10Mg alloy produced by Additive Manufacturing

E. Salerno, D. Casotti, E. Gualtieri, A. Ballestrazzi, G.C. Gazzadi, G. Bolelli, L. Lusvarghi, A. Rota, S. Valeri, G. Paolicelli

Abstract

Al–Si alloys are attractive materials for the fabrication of mechanical components, mainly because of their high strength-to-density ratio. Though the advent of Selective Laser Melting (SLM) has potentially expanded the range of their applicability, their poor tribological performances limit their effective use. Identifying post-processing protocols and coating strategies enhancing these properties and compatible with large-scale production is fundamental to the industrial uptake of SLM-fabricated Al–Si parts. This work tests the possibility of depositing self-lubricating Diamond-Like Carbon (DLC)-terminated films on AlSi10Mg built by SLM and subjected to different surface finishing processes. The applied coating architectures consist of an electroless nickel‐phosphorus buffer layer deposited on the AlSi10Mg surface, plus a series of interlayers and a DLC top film grown by Plasma Assisted – Chemical Vapor Deposition. The wear resistance and frictional behavior of the samples are evaluated for different substrate pre-treatments and coating assemblies under two applied loads. Cast substrates, processed and coated in a similar way, are also studied for comparison. The DLC film lends good tribological performances to all the coating-substrate combinations explored, being mechanically assisted by the underlying Ni–P layer. The friction coefficients stabilize around 0.20 at the lowest load, independently of the sample surface roughness (S q ), which spans the range 0.47–4.6 μm. Conversely, the counterpart wear rates increase with roughness up to 10 −5 mm 3 /(N⋅m). Both tribological parameters decrease by nearly 20 % and 70 %, respectively, after a tenfold increase in load. These results indicate that DLC-terminated multilayers are extremely efficient on AlSi10Mg even in the presence of significant roughness. Their application requires a limited number of well-established processing steps also in the case of SLM grown parts. • DLC coatings systems are deposited on additive manufacturing AlSi10Mg substrates. • Coatings systems starts with a Ni–P layer and terminate with a DLC film deposited by PA-CVD. • Substrates and films are grown with industrial production systems and related standards. • DLC coatings systems effectively reduce friction and wear on additive AlSi10Mg substrates. • Wear tracks on the coated discs are scarcely detectable in any of the samples and conditions explored.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (66)

Show source-provided references
1. The increasing use of aluminum in automotive applications10.1007/BF03221224 ↗
2. Overview
3. Aluminum Alloys
4. Development and applications of aluminum alloys for aerospace industry10.1016/j.jmrt.2023.09.274 ↗
5. Aluminum alloys: promising materials in the automotive industry10.1023/A:1021901715578 ↗
6. Aluminum alloys for lightweight automotive structures
7. Application of cast Al–Si alloys in internal combustion engine components10.1179/1743280413Y.0000000027 ↗
8. Wear characteristics, friction and surface topography observed in the dry sliding of as-cast and age-hardening Al-Si alloys10.1016/0043-1648(82)90140-5 ↗
9. A parametric study of the relationship between microstructure and wear resistance of Al-Si alloys10.1016/j.wear.2006.03.043 ↗
10. Revolutionizing manufacturing: a comprehensive overview of additive manufacturing processes, materials, developments, and challenges10.1016/j.jmapro.2023.10.024 ↗
11. Challenges in additive manufacturing of high-strength aluminium alloys and current developments in hybrid additive manufacturing
12. 3D printing of Aluminium alloys: additive manufacturing of Aluminium alloys using selective laser melting10.1016/j.pmatsci.2019.100578 ↗
13. A review of selective laser melting of aluminum alloys: processing, microstructure, property and developing trends10.1016/j.jmst.2018.09.004 ↗
14. Modification of eutectic silicon in Al–Si alloys10.1007/s10853-008-2505-5 ↗
15. Microstructure and mechanical properties of AlSi10Mg parts produced by the laser beam additive manufacturing (AM) technology10.1007/s13632-014-0168-y ↗
16. On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM)
17. Additive manufactured versus cast AlSi10Mg alloy: microstructure and micromechanics
18. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder10.1016/j.actamat.2012.11.052 ↗
19. Tribological and corrosion properties of Al-12Si produced by selective laser melting10.1557/jmr.2014.133 ↗
20. Tribological behavior of aluminum alloy AlSi10Mg-TiB2 composites produced by direct metal laser sintering (DMLS)10.1007/s11665-016-2190-5 ↗
21. Microstructure and wear behavior of in-situ hypereutectic Al-high Si alloys produced by selective laser melting10.1016/j.matdes.2016.03.053 ↗
22. An experimental investigation into the dry reciprocating Wear behavior of additively manufactured AlSi10Mg alloys10.1007/s11837-023-06187-6 ↗
23. An overview on the tribological behavior of diamond-like carbon in technical and medical applications10.1016/j.triboint.2004.07.017 ↗
24. Diamond-like carbon coatings for tribology applications10.1179/174328007X160272 ↗
25. An updated overview of diamond-like carbon coating in tribology10.1080/10408436.2014.940441 ↗
26. Synergistic effect of graphene and nanodiamonds to achieve ultra-low friction on rough DLC coatings10.1016/j.diamond.2024.111149 ↗
27. Bonding and sliding wear behaviour of diamond-like carbon coatings on fiber reinforced aluminium10.1016/S0257-8972(98)00625-2 ↗
28. Diamond-like carbon: state of the art10.1016/S0925-9635(98)00262-3 ↗
29. Tribology of diamond-like carbon coatings: fundamentals and applications, springer science
30. Coating Technology for Vehicle Applications, springer international publishing
31. Mechanical and Tribological requirements and evaluation of coating composites
32. The effects of beam energy and substrate temperature on the tribological properties of hard-carbon films on aluminum10.1016/0257-8972(92)90228-3 ↗
33. High adhesion of diamond-like carbon thin film to an aluminum alloy achieved by substrate sputtering and redeposition method10.1016/j.surfcoat.2011.07.003 ↗
34. Diamond-like carbon coating for aluminum 390 alloy-automotive application10.1016/S0257-8972(97)00061-3 ↗
35. Wear and corrosion behaviour of HVOF WC-CoCr/CVD DLC hybrid coating systems deposited onto Aluminium substrate10.1016/j.surfcoat.2011.03.021 ↗
36. Characterization of duplex coating system (HVOF + PVD) on light alloy substrates10.1016/j.surfcoat.2016.06.020 ↗
37. Tribological response of AA 2024-T3 aluminium alloy coated with a DLC duplex coating10.1016/j.triboint.2014.12.007 ↗
38. Deposition of duplex Al2O3/DLC coatings on Al alloys for tribological applications using a combined micro-arc oxidation and plasma-immersion ion implantation technique10.1016/S0257-8972(00)00816-1 ↗
39. Friction mechanism of DLC/MAO wear-resistant coatings with porous surface texture constructed in-situ by micro-arc oxidation
40. Gradient DLC-based nanocomposite coatings as a solution to improve Tribological performance of aluminum alloy10.1007/s11249-010-9585-5 ↗
41. Wear and friction characteristics of AlN/diamond-like carbon hybrid coatings on aluminum alloy10.1007/s11665-015-1694-8 ↗
42. Microstructure, mechanical properties and low-temperature tribological behavior of Cr/Cr-W/W-DLC/DLC multilayer coatings on 5A06 Al alloy10.1016/j.jmrt.2022.03.002 ↗
43. Adhesion and durability of multi-interlayered diamond-like carbon films deposited on aluminum alloy10.1016/j.surfcoat.2018.08.094 ↗
44. Microstructure, mechanical and tribological properties of multilayer Ti-DLC thick films on Al alloys by filtered cathodic vacuum arc technology10.1016/j.matdes.2020.109320 ↗
45. Surface roughness analysis, modelling and prediction in selective laser melting10.1016/j.jmatprotec.2012.11.011 ↗
46. Effect of selective laser melting process parameters on the quality of Al alloy parts: powder characterization, density, surface roughness, and dimensional accuracy10.3390/ma11122343 ↗
47. A review on corrosion and Wear of additively manufactured alloys10.1115/1.4050503 ↗
48. Friction and wear of DLC films deposited on additive manufactured AlSi10Mg: the role of surface finishing10.1016/j.surfcoat.2023.129531 ↗
49. Fatigue behavior of a 7075-T6 aluminum alloy coated with an electroless Ni–P deposit10.1016/j.ijfatigue.2005.12.005 ↗
50. Microstructure and corrosion behavior of electroless Ni-P coatings on 6061 aluminum alloys10.1007/s11998-010-9256-3 ↗
51. Effect of deposition time on the morphological features and corrosion resistance of Electroless Ni-high P coatings on Aluminium
52. Electroless nickel, alloy, composite and nano coatings - a critical review10.1016/j.jallcom.2013.03.107 ↗
53. Sha · 2011
54. Determination of bonding in diamond-like carbon by Raman spectroscopy10.1016/S0925-9635(01)00730-0 ↗
55. Interpretation of Raman spectra of disordered and amorphous carbon10.1103/PhysRevB.61.14095 ↗
56. Raman spectroscopy of hydrogenated amorphous carbons10.1103/PhysRevB.72.085401 ↗
57. An investigation into the effect of substrate on the load-bearing capacity of thin hard coatings10.1007/s10853-016-9751-8 ↗
58. Environmental and thermal effects on the Tribological performance of DLC coatings
59. Tribological performance of an H-DLC coating prepared by PECVD10.1016/j.apsusc.2016.04.184 ↗
60. Effects of sliding velocity and normal load on friction and wear characteristics of multi-layered diamond-like carbon (DLC) coating prepared by reactive sputtering10.1016/j.wear.2012.10.009 ↗
61. Effect of normal loads and mating pairs on the tribological properties of diamond-like carbon film10.1016/j.wear.2021.204083 ↗
62. An investigation of the relationship between graphitization and frictional behavior of DLC coatings10.1016/S0257-8972(96)03057-5 ↗
63. Problematic of heat treatment and its influence on mechanical properties of selectively laser melted AlSi10Mg alloy10.1007/s00170-021-08521-1 ↗
64. Contact of nominally flat surfaces10.1098/rspa.1966.0242 ↗
65. The elastic contact of a rough surface10.1016/0043-1648(75)90145-3 ↗
66. Contact mechanics for randomly rough surfaces10.1016/j.surfrep.2006.04.001 ↗