journal article·2018-11

Experimental and numerical study for Cu metal coatings at room temperature via powder spray process

Dong-Won Lee, Myung-Yeon Cho, Ik-Soo Kim, Yong-Nam Kim, Daeseok Lee, Sang-Mo Koo, Chulhwan Park, Jong-Min Oh

Publisher page

Abstract

Abstract The effect of Cu particle size on deposition behavior of Cu coating layer was investigated by experimental and numerical studies to understand coating behavior of metal films during aerosol deposition (AD) process. Experimental results showed that Cu film fabricated using 2 μm Cu powder had high deposition rate, low resistivity, and high internal micro-strain. Moreover, Cu films fabricated using 2 μm Cu powder had dense microstructure and Cu oxide phases due to elevated temperature caused by kinetic energy of impacted particles. However, Cu films prepared with 5 μm Cu powder formed filmy deposition layers with poor structural and electrical properties. Numerical results revealed that the generated strain and heat at the impact interface between the particle and the substrate were significantly decreased with increasing particle size. In contrast, the maximum shock pressure of particles was increased with increasing particle size. These results demonstrate that metal Cu particle with size of about 2 μm is suitable for forming good quality coating layers and that their bonding is associated with high compressive strain and thermal energy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Particle Dynamics in Fluid Flows · High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Microstructure and electrical properties of lead zirconate titanate (Pb(Zr52/Ti48)O3) thick films deposited by aerosol deposition method10.1143/JJAP.38.5397 ↗
2. Optically transparent, dense a-Al2O3 thick films deposited on glass at room temperature10.1016/j.cap.2007.10.057 ↗
3. Effect of film thickness on the piezoelectric properties of lead zirconate titanate thick films fabricated by aerosol deposition10.1111/j.1551-2916.2010.04276.x ↗
4. Substrate hardness dependency on properties of Al2O3 thick films grown by aerosol deposition10.1016/j.surfcoat.2012.08.012 ↗
5. Room temperature impact consolidation (RTIC) of fine ceramic powder by aerosol deposition method and applications to microdevices10.1007/s11666-008-9163-7 ↗
6. Alumina thick films as integral substrates using aerosol deposition method10.1143/JJAP.43.5414 ↗
7. Aerosol deposition for post-LTCC10.1016/j.jeurceramsoc.2006.11.055 ↗
8. Role of surface hardness of substrates in growing BaTiO3 thin films by aerosol deposition method10.1143/JJAP.48.09KA07 ↗
9. Thickness limit of BaTiO3 thin film capacitors grown on SUS substrates using aerosol deposition method10.1016/j.tsf.2010.03.159 ↗
10. Aerosol deposition on transparent electro-optic films for optical modulators10.1093/ietele/e90-c.1.36 ↗
11. Photocatalytic TiO2 thin films by aerosol-deposition: from micron-sized particles to nano-grained thin film at room temperature10.1016/j.apcatb.2008.01.020 ↗
12. Halogen plasma erosion resistance of rare earth oxide films deposited on plasma sprayed alumina coating by aerosol deposition10.1016/j.jeurceramsoc.2012.02.019 ↗
13. Hydroxyapatite film formed by particle beam irradiation10.1016/j.vacuum.2003.12.082 ↗
14. Mechanical and in vitro biological performances of hydroxyapatite–carbon nanotube composite coatings deposited on Ti by aerosol deposition10.1016/j.actbio.2009.05.005 ↗
15. Brushite ceramic coatings for dental brace brackets fabricated via aerosol deposition10.1016/j.ceramint.2016.10.037 ↗
16. Preparation of ultrasensitive humidity-sensing by aerosol deposition10.1021/acsami.7b14082 ↗
17. Thickness effects of aerosol deposited hygroscopic films on ultra-sensitive humidity sensors10.1016/j.snb.2018.03.093 ↗
18. Aerosol deposition of ceramic thick films at room temperature: densification mechanism of ceramic layers10.1111/j.1551-2916.2006.01030.x ↗
19. Growth process of α-Al2O3 ceramic films on metal substrates fabricated at room temperature by aerosol deposition10.1111/j.1551-2916.2011.04493.x ↗
20. Deposition mechanism of dry sprayed ceramic particles at room temperature using a nano-particle deposition system10.1016/j.actamat.2011.01.007 ↗
21. Compression test system for a single submicrometer particle10.1063/1.2038187 ↗
22. Plastic deformation and allotropic phase transformations in zirconia ceramics during high-pressure torsion10.1016/j.scriptamat.2011.08.024 ↗
23. The role of plasticity as a limiting factor in the compressive failure of high strength ceramics10.1016/S0167-6636(98)00023-4 ↗
24. Dynamic plasticity and failure of high-purity alumina under shock loading10.1038/nmat1689 ↗
25. Damage evolution in dynamic deformation of silicon carbide
26. Microstructure evolution of titanium nitride film during vacuum kinetic spraying10.1111/jace.12101 ↗
27. Molecular dynamics simulation on the single particle impacts in the aerosol deposition process10.2320/matertrans.46.1235 ↗
28. Gas dynamic principles of cold spray10.1361/105996398770350945 ↗
29. The cold spray process and its potential for industrial applications10.1361/105996306X108110 ↗
30. Silver metallization for microwave device using aerosol deposition10.1016/j.ceramint.2011.04.083 ↗
31. Characteristics and mechanism of Cu films fabricated at room temperature by aerosol deposition
32. Densification mechanism of BaTiO3 films on Cu substrates fabricated by aerosol deposition10.1007/s13391-015-4419-0 ↗
33. Porous photocatalytic TiO2 thin films by aerosol deposition10.1111/j.1551-2916.2009.03391.x ↗
34. Effect of powder polydispersity on aerosol generation
35. Century Dynamics Inc. · 2008
36. Influence of carrier gas conditions on electrical and optical properties of Pb(Zr, Ti)O3 thin films prepared by aerosol deposition method10.1143/JJAP.40.5528 ↗
37. Gas dynamic simulation of aerosol deposition method10.2320/matertrans.47.1620 ↗
38. General form of the Mie–Grüneisen equation of state10.1016/j.crme.2012.10.044 ↗
39. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗
40. Development of a generalized parameter window for cold spray deposition10.1016/j.actamat.2005.10.005 ↗
41. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures10.1016/0013-7944(85)90052-9 ↗
42. Numerical simulation of long rods impacting silicon carbide targets using JH-1 model10.1016/j.ijimpeng.2006.09.011 ↗
43. The prediction of the dynamic responses of ceramic particle reinforced MMCs by using multi-particle computational micro-mechanical method10.1016/j.compscitech.2007.02.002 ↗
44. Optimal design of a convergent-barrel cold spray nozzle by numerical method10.1016/j.apsusc.2006.11.020 ↗
45. X-ray line broadening from field aluminium and wolfram10.1016/0001-6160(53)90006-6 ↗
46. XPS and ISS studies on the interaction of H2S with polycrystalline Cu, Cu2O and CuO surfaces10.1002/sia.740230308 ↗
47. Interface effects for Cu, CuO, and Cu2O deposited on SiO2 and ZrO2. XPS determination of the valence state of copper in Cu/SiO2 and Cu/ZrO2 catalysts10.1021/jp014618m ↗