Influence of hexamethyldisilazane vapor on the structure and mechanical properties of TiC-based coatings
Source abstract
Abstract
Abstract Silicon-modified titanium carbide (TiC) coatings exhibit excellent properties and are attractive for a variety of protective coating applications. These coatings are often produced by sputtering silicon from elemental or composite targets, which limits both large area compositional uniformity and the ability to grade silicon composition to improve coating adhesion. Here we demonstrate the use of an organosilicon vapor, hexamethyldisilazane (HMDS), as a silicon source during the plasma enhanced magnetron sputtering (PEMS) of TiC-based coatings. Three coatings, with compositionally graded interlayers, were deposited under various HMDS flow rates onto silicon and stainless steel substrates. The growth structures of the coatings were characterized by scanning electron microscopy and atomic force microscopy. The introduction of HMDS under low flow conditions resulted in an increase in root-mean-square surface roughness from 13 to 41 nm, however, the coating was characterized by a similar columnar growth structure as produced without HMDS flow. At higher HMDS flow, columnar growth was disrupted due to the segregation of sufficient amounts of silicon and excess carbon. Coating composition, as determined by energy dispersive X-ray spectroscopy, indicates that the densification of the growth structure occurred at titanium, silicon, and carbon contents of 29, 9, and 57 at.%, respectively. X-ray diffraction analysis demonstrated that all coatings contained rock-salt structure phases (TiC, TiCN) with 〈111〉 out-of-plane texture. Raman spectroscopy and X-ray photoelectron spectroscopy confirmed the presence of amorphous phases, consisting primarily of silicon and excess carbon (a-C:H/a-SiCx:H), in both coatings produced with HMDS. The simultaneous disruption of columnar growth and formation of a composite microstructure consisting of crystalline and amorphous phases at high HMDS flow resulted in improved mechanical properties when compared to the TiC control coating, evidenced by an increase in the H/E ratio from 0.063 to 0.10. The processing methods demonstrated here may potentially be applied to industrial settings for improved compositional control during the introduction of silicon to TiC-based coatings.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (75)
Show source-provided references
1. Sputter deposition of transition-metal carbide films - a critical review from a chemical perspective10.1016/j.tsf.2013.02.019 ↗
2. Properties of diamond-like carbon10.1016/0257-8972(92)90001-Q ↗
3. Supertough wear-resistant coatings with ‘chameleon’ surface adaptation10.1016/S0040-6090(00)00917-2 ↗
4. Nanostructure and properties of TiC/a-C:H composite coatings10.1016/j.actamat.2005.05.045 ↗
5. Microstructural evolution during film growth10.1116/1.1601610 ↗
6. Corrosion and tribo-corrosion behavior of a-SiCx:H, a-SiNx:H and a-SiCxNy:H coatings on SS301 substrate10.1016/j.surfcoat.2009.10.018 ↗
7. The Mn+1AXn phases: materials science and thin-film processing10.1016/j.tsf.2009.07.184 ↗
8. Layered ternary Mn+1AXn phases and their 2D derivative MXene: an overview from a thin-film perspective10.1088/1361-6463/aa57bc ↗
9. Structure and high-temperature tribological behavior of Ti-Si-C nanocomposite thin films10.1016/j.surfcoat.2004.12.011 ↗
10. Structural, electrical, and mechanical properties of nc-TiC∕a-SiC nanocomposite thin films10.1116/1.2131081 ↗
11. On the chemistry at the Si,Ti-doped a-C:H/TiC interface10.1016/S0040-6090(03)01324-5 ↗
12. Effect of Si and C concentration on the microstructure, and the mechanical, tribological and electrochemical properties of nanocomposite TiC/a-SiC:H/a-C:H coatings prepared by plasma enhanced chemical vapor deposition
13. In situ tribology of nanocomposite Ti-Si-C-H coatings prepared by PE-CVD10.1016/j.wear.2011.08.001 ↗
14. Wear protective coatings consisting of TiC-SiC-a-C:H deposited by magnetron sputtering10.1016/S0257-8972(02)00477-2 ↗
15. Mechanical, tribological and erosion behaviour of super-elastic hard Ti-Si-C coatings prepared by PECVD10.1016/j.surfcoat.2010.07.098 ↗
16. Incorporation effects of Si in TiCx thin films10.1016/j.surfcoat.2014.08.064 ↗
17. Annealing studies of nanocomposite Ti-Si-C thin films with respect to phase stability and tribological performance10.1016/j.msea.2006.05.053 ↗
18. Influence of composition and structural properties in the tribological behaviour of magnetron sputtered Ti-Si-C nanostructured thin films, prepared at low temperature10.1016/j.wear.2009.10.001 ↗
19. Magnetron sputtered Ti-Si-C thin films prepared at low temperatures10.1016/j.surfcoat.2007.01.025 ↗
20. Superlow friction of titanium/silicon codoped hydrogenated amorphous carbon film in the ambient air10.1063/1.3462469 ↗
21. High-power impulse magnetron sputtering of Ti-Si-C thin films from a Ti3SiC2 compound target10.1016/j.tsf.2006.06.015 ↗
22. High-rate deposition of amorphous and nanocomposite Ti-Si-C multifunctional coatings10.1016/j.surfcoat.2010.06.051 ↗
23. Microstructure and tribological performance of nanocomposite Ti–Si–C–N coatings deposited using hexamethyldisilazane precursor10.1116/1.3463709 ↗
24. TEM characterization of a Cr/Ti/TiC graded interlayer for magnetron-sputtered TiC/a-C:H nanocomposite coatings10.1016/j.actamat.2005.04.040 ↗
25. A comparative study of conventional magnetron sputter deposited and plasma enhanced magnetron sputter deposited Ti-Si-C-N nanocomposite coatings10.1016/j.surfcoat.2013.08.049 ↗
26. The effect of microstructure and composition on mechanical properties in thick-layered nanocomposite Ti-Si-C-N coatings10.1016/j.surfcoat.2010.07.070 ↗
27. A comparative study of thick TiSiCN nanocomposite coatings deposited by dcMS and HiPIMS with and without PEMS assistance10.1016/j.surfcoat.2018.01.082 ↗
28. Deposition of thick nitrides and carbonitrides for sand erosion protection10.1016/j.surfcoat.2006.08.091 ↗
29. Effect of ion bombardment on structural, mechanical, erosion and corrosion properties of Ti-Si-C-N nanocomposite coatings10.1016/j.surfcoat.2014.09.006 ↗
30. Development and evaluation of low friction TiSiCN nanocomposite coatings for piston ring applications10.1016/j.surfcoat.2016.04.061 ↗
31. First-principles study of metal-carbide/nitride adhesion: Al/VC vs. Al/VN10.1016/S1359-6454(01)00361-5 ↗
32. Preparation of silicon carbide coating by chemical vapor deposition by using hexamethyldisilylamine precursor10.1016/j.surfcoat.2017.11.017 ↗
33. Levinson · 2010 · 37
34. The VDI 3198 indentation test evaluation of a reliable qualitative control for layered compounds10.1016/S0924-0136(03)00300-5 ↗
35. Critical review of analysis and interpretation of nanoindentation test data10.1016/j.surfcoat.2005.03.018 ↗
36. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
37. Properties of metal-matrix composites
38. Evolution of microstructure and macrostress in sputtered hard Ti(Al,V)N films with increasing energy delivered during their growth by bombarding ions
39. Microstructural control of TiC/a-C nanocomposite coatings with pulsed magnetron sputtering10.1016/j.actamat.2007.10.025 ↗
40. Mechanisms of reactive sputtering of titanium nitride and titanium carbide I: influence of process parameters on film composition10.1016/0040-6090(83)90318-8 ↗
41. Structure refinement of titanium carbonitride (TiCN)10.1016/S0167-577X(97)00276-0 ↗
42. Studies on the crystal structure, magnetic and conductivity properties of titanium oxycarbide solid solution (TiO1-xCx)10.1039/C6TA00042H ↗
43. Thermal expansion of some transition metal carbides10.1021/j150563a030 ↗
44. The crystal structure and chemical character of lower oxides of titanium TiO0→0.4810.1007/BF00738933 ↗
45. The temperature factor parameters of some transition metal carbides and nitrides by single crystal x-ray and neutron diffraction10.3891/acta.chem.scand.32a-0089 ↗
46. Growth of Ti-C nanocomposite films by reactive high power impulse magnetron sputtering under industrial conditions10.1016/j.surfcoat.2011.10.039 ↗
47. Lattice expansion of Ti-6Al-4V by nitrogen and oxygen absorption10.1016/j.matchar.2006.12.014 ↗
48. X-ray diffraction analysis of titanium carbonitride 30/70 and 70/30 solid solutions10.1017/S0885715600016043 ↗
49. Micro-Raman studies on DLC coatings10.1002/adem.200500006 ↗
50. Mechanical properties of Ti-containing and W-containing diamond-like carbon coatings10.1063/1.368650 ↗
51. Raman scattering induced by carbon vacancies in TiCx10.1103/PhysRevB.17.1546 ↗
52. X-ray photoelectron spectroscopy study of the difference between reactively evaporated and direct sputter-deposited TiN films and their oxidation properties10.1116/1.579711 ↗
53. Titanium nitride oxidation chemistry: an x-ray photoelectron spectroscopy study10.1063/1.351465 ↗
54. Reactive and nonreactive ion mixing of Ti films on carbon substrates10.1116/1.574992 ↗
55. AES and XPS analysis of the interaction of Ti with Si and SiO2 during RTA10.1016/0169-4332(89)90516-3 ↗
56. The contribution of characteristic energy losses in the core-level X-ray photoelectron spectroscopy peaks of TiN and (Ti, Al)N studied by electron energy loss spectroscopy and X-ray photoelectron spectroscopy10.1016/0368-2048(91)80007-H ↗
57. XPS study of thin films of titanium oxysulfides10.1016/0039-6028(91)90640-E ↗
58. On the determination of atomic charge via ESCA including application to organometallics10.1016/0368-2048(95)02392-5 ↗
59. Characterization of TiN films prepared by a conventional magnetron sputtering system: influence of nitrogen flow percentage and electrical properties10.1016/S0040-6090(96)08749-4 ↗
60. Thermal nitridation of silicon in a cluster tool10.1063/1.106651 ↗
61. Nitrogen 1s charge referencing for Si3N4 and related compounds10.1002/sia.740110611 ↗
62. Oxidation studies of crystalline CVD silicon nitride10.1149/1.2096955 ↗
63. Synthesis of α-silicon nitride powder from a polymeric precursor10.1016/0955-2219(95)00011-I ↗
64. Modification of surface band bending of diamond by low energy argon and carbon ion bombardment10.1063/1.357016 ↗
65. Carbonaceous overlayers on Ru(001)10.1116/1.573460 ↗
66. Bhushan · 2002 · 10
67. On the origin of a third spectral component of C1s XPS-spectra for nc-TiC/a-C nanocomposite thin films10.1016/j.surfcoat.2007.12.038 ↗
68. Hardness and Young's modulus of amorphous a-SiC thin film determined by nanoindentation and bulge tests10.1557/JMR.1994.0096 ↗
69. ASM International Handbook Committee · 1990
70. Pierson · 1996
71. Tribological and mechanical properties of nanocrystalline-TiC/a-C nanocomposite thin films10.1116/1.3294717 ↗
72. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour10.1016/S0043-1648(00)00488-9 ↗
73. Toughness of hard nanostructured ceramic thin films10.1016/j.surfcoat.2006.07.020 ↗
74. Deformation and failure mechanism of nano-composite coating under nano-indentation10.1016/j.surfcoat.2005.10.010 ↗
75. Flexible hard nanocomposite coatings10.1039/C5RA09586G ↗