Characterization of protective AlCrON thin films for application on sensor thin films in fused layer modeling processes
Source abstract
Abstract
In plastic processing, the use of sensor thin films is gaining interest for inline measurement to ensure stable process control. However, due to the corrosive and abrasive characteristics of molten plastics, the application of an appropriate protective coating becomes imperative to ensure the functionality of the sensor films. AlCrON thin films demonstrate favorable protective attributes for this purpose. The tribo-mechanical and electrical properties are inherently influenced by the oxygen content. Therefore, a systematic variation of O 2 gas flow rates (10 to 30 sccm in steps of five) during the mid-frequency magnetron sputtering process was employed resulting in the O contents rise from 12.2 at.-% for 10 mln O 2 to 57.6 at.-% for 30 mln O 2 . Simultaneously, a change of a polycrystalline structure containing CrN, Cr 2 N, and hexagonal AlN to an amorphous structure with increasing O content for AlCrON is observed. This affects the tribo-mechanical properties. The highest polycrystallinity was reached at 25.2 at.-% O resulting in a H/E maximum, with a maximum in hardness of (37.6 ± 2.8) GPa and an elastic modulus of (361.2 ± 20.7) GPa. Here, also the lowest coefficient of friction (CoF) at elevated temperatures was reached with 0.43 against polypropylene (PP) and 0.23 against polyamide (PA). The low CoF correlates with a lower wetting ability of the AlCrON thin film. Regarding the electrical properties AlCrON thin films show insulating characteristics dependent on the O content. The electrical resistance increases with higher O content due to a change into a more ionic structure. The results show that AlCrON thin films offer promising protective qualities for sensor applications in plastic processing. By adjusting the oxygen content, their tribo-mechanical properties can be optimized for reduced friction and enhanced durability, while their insulating properties are promising for maintaining the functionality of the sensors. • Oxide transformation at (Al + Cr)/(O + N) of 0.66 • Oxynitridic structure with AlCrN and Cr 2 N phases shows the highest hardness. • Lower wettability reduces CoF depending on processed plastic. • Decreasing electrical conductivity with increasing O content
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Analytical Chemistry and Sensors · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. Characterization of the mechanical properties of FFF structures and materials: a review on the experimental, computational and theoretical approaches
2. Fused deposition modeling process parameters optimization and effect on mechanical properties and part quality
3. Investigating pressure advance algorithms for filament-based melt extrusion additive manufacturing: theory, practice and simulations10.1108/RPJ-10-2018-0275 ↗
4. Extruded diameter dependence on temperature and velocity in the fused deposition modeling process10.1007/s40964-019-00107-4 ↗
5. Wohlers Associates, Wohlers Report: Additive Manufacturing and 3D Printing State of the Industry; Annual Worldwide Progress Report, 2020.
6. M. Plogmeyer, G. González, C. Pongratz, A. Schott, V. Schulze, G. Bräuer, Tool-integrated thin-film sensor systems for measurement of cutting forces and temperatures during machining, Prod. Eng. Res. Devel. doi:https://doi.org/10.1007/s11740-023-01251-1.10.1007/s11740-023-01251-1 ↗
7. Influence of Cr-content on the thermoelectric and mechanical properties of NiCr thin film thermocouples synthesized on thermally sprayed Al2O310.1016/j.tsf.2018.08.023 ↗
8. Combining thermal spraying and magnetron sputtering for the development of Ni/Ni-20Cr thin film thermocouples for plastic flat film extrusion processes10.3390/coatings9100603 ↗
9. Advanced composite materials utilized in FDM/FFF 3D printing manufacturing processes: the case of filled filaments
10. Mechanical properties of 3D parts fabricated by fused deposition modeling: effect of various fillers in polylactide10.1002/app.47824 ↗
11. Tailoring strength and modulus by 3D printing different continuous fibers and filled structures into composites10.1007/s42114-019-00087-7 ↗
12. Sputtering physical vapour deposition (PVD) coatings: a critical review on process improvement and market trend demands10.3390/coatings8110402 ↗
13. Tantalum oxide thin films as protective coatings for sensors10.1088/0960-1317/9/2/003 ↗
14. High temperature failure modes of In2O3 thin films and improved thermal stability using Al2O3/ZrO2 protective layers10.1016/j.ceramint.2021.06.258 ↗
15. Wear resistance of hard coatings in plastics processing10.1016/S0257-8972(98)00449-6 ↗
16. Performance of chromium nitride based coatings under plastic processing conditions10.1016/S0257-8972(00)00875-6 ↗
17. Residual stress, surface defects and corrosion resistance of CrN hard coatings10.1016/S0257-8972(98)00731-2 ↗
18. Oxidation resistance of TiN, CrN, TiAlN and CrAlN coatings deposited by lateral rotating cathode arc10.1016/j.tsf.2009.03.038 ↗
19. Friction and wear properties of CrAlN and CrVN films deposited by cathodic arc ion plating method10.1016/S0257-8972(03)00937-X ↗
20. A study of the oxidation behavior of CrN and CrAlN thin films in air using DSC and TGA analyses10.1016/j.surfcoat.2007.11.037 ↗
21. G. Biava, I.B. de Araujo Fernandes Siqueira, R.F. Vaz, G.B. de Souza, H.C.M. Jambo, A. Szogyenyi, A.G. Pukasiewicz, Evaluation of high temperature corrosion resistance of CrN, AlCrN, and TiAlN arc evaporation PVD coatings deposited on Waspaloy, Surf. Coat. Technol. 438 (2022) 128398. doi:https://doi.org/10.1016/j.surfcoat.2022.128398.10.1016/j.surfcoat.2022.128398 ↗
22. R. K., P. S., Corrosion of metal – oxide systems, in: H. Shih (Ed.), Corrosion Resistance, InTech, 2012.10.5772/33144 ↗
23. Surface and interface analysis of PVD Al-O-N and γ-Al 2 O 3 diffusion barriers10.1007/s002160051464 ↗
24. Ion-plated Al–O–N and Cr–O–N films on Ni-base superalloys as diffusion barriers10.1016/j.surfcoat.2004.09.022 ↗
25. Thermal stability of arc evaporated Al-Cr-O-N coatings10.1016/j.surfcoat.2018.09.036 ↗
26. CrAlON CAE-PVD coatings for oxidation and wear protection of TZM alloys in FAST sintering applications10.1016/j.matchemphys.2018.01.056 ↗
27. Structural evolution and high-temperature tribological properties of AlCrON coatings deposited by multi-arc ion plating10.1016/j.ceramint.2020.06.208 ↗
28. Correlation between anionic substitution and structural properties in AlCr(OxN1−x) coatings deposited by lateral rotating cathode arc PVD10.1016/j.tsf.2011.08.075 ↗
29. PVD—coatings in injection molding machines for processing optical polymers10.1002/ppap.200730507 ↗
30. Hybrid dcMS/HPPMS PVD nitride and oxynitride hard coatings for adhesion and abrasion reduction in plastics processing10.1016/j.surfcoat.2016.07.103 ↗
31. Bobzin · Surf. Coat. Technol. · 2016 · 308 · 39410.1016/j.surfcoat.2016.07.093 ↗
32. N. Bagcivan, K. Bobzin, T. Brögelmann, C. Kalscheuer, Development of (Cr,Al)ON coatings using middle frequency magnetron sputtering and investigations on tribological behavior against polymers, Surf. Coat. Technol. 260 (2014) 347–361. doi:https://doi.org/10.1016/j.surfcoat.2014.09.016.10.1016/j.surfcoat.2014.09.016 ↗
33. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
34. High temperature oxidation and cutting performance of AlCrN, TiVN and multilayered AlCrN/TiVN hard coatings10.1016/j.surfcoat.2017.06.080 ↗
35. DIN 4856:2018-02, Kohlenstoffschichten und andere Hartstoffschichten_-Rockwell-Eindringprüfung zur Bewertung der Haftung, Beuth Verlag GmbH, Berlin.
36. DIN EN ISO 20502:2016-11, Hochleistungskeramik_-Bestimmung der Haftung von keramischen Schichten mit dem Ritztest (ISO_20502:2005 einschließlich Cor_1:2009); Deutsche Fassung EN_ISO_20502:2016, Beuth Verlag GmbH, Berlin.
37. Erhard · 2008
38. Schwarz · 1987
39. Tribological performance of PVD film systems against plastic counterparts for adhesion-reducing application in injection molds10.3390/coatings9090588 ↗
40. Contact angle measurement and contact angle interpretation10.1016/S0001-8686(98)00087-6 ↗
41. Influence of oxygen content on structure, thermal stability, oxidation resistance, and corrosion resistance of arc evaporated (Cr, Al)N coatings10.1016/j.surfcoat.2021.128057 ↗
42. Allison · 2013
43. Structural and mechanical properties of Cr–Al–O–N thin films grown by cathodic arc deposition10.1016/j.actamat.2012.08.010 ↗
44. Thermal stability of Al–Cr–N hard coatings10.1016/j.scriptamat.2006.02.023 ↗
45. 2017
46. Preparation and characterization of CrN thin film by DC reactive magnetron sputtering
47. CrN thin films prepared by reactive DC magnetron sputtering for symmetric supercapacitors10.1039/C6TA09985H ↗
48. Magnetron sputtering of aluminium using oxygen or nitrogen as reactive gas10.1016/S0040-6090(97)01197-8 ↗
49. Chemical and mechanical stability of air annealed cathodic arc evaporated CrAlON coatings10.1016/j.surfcoat.2018.07.081 ↗
50. Effect of oxygen content on wear and cutting performance of AlCrON coatings10.1007/s11665-018-3823-7 ↗
51. Influence of oxygen content on structure and properties of multi-element AlCrSiON oxynitride thin films10.1016/j.surfcoat.2010.02.029 ↗
52. Characterization of AlCrN and AlCrON coatings deposited on plasma nitrided AISI H13 steels using ion-source-enhanced arc ion plating10.3390/coatings10040306 ↗
53. Microstructure of Al95.5Cr2.5Si2(N1−xOx) thin films covering from nitrides to oxides10.1016/j.surfcoat.2011.05.031 ↗
54. Hard and superhard nanocomposite coatings10.1016/S0257-8972(99)00586-1 ↗
55. Comparative study of the tribological behaviour of superhard nanocomposite coatings nc-TiN/a-Si3N4 with TiN10.1016/j.surfcoat.2004.05.007 ↗
56. A. Munteanu, D. Munteanu, B. Borcea, F. Vaz, L. Cunha, C. Olteanu, The influence of the deposition conditions on the mechanical properties of TI(C,O,N) thin films obtained by sputtering process, Metalurgia Int. 14 (2009) 129–132.
57. Evaluation of adhesion and tribological behaviour of tantalum oxynitride thin films deposited by reactive magnetron sputtering onto steel substrates10.1016/j.surfcoat.2005.11.079 ↗
58. Photocatalytical and corrosion behavior of sputtered zirconium oxynitride thin films doped with titanium10.1016/j.surfin.2023.103488 ↗
59. Influence of the chemical and electronic structure on the electrical behavior of zirconium oxynitride films10.1063/1.2927494 ↗
60. Influence of substrate temperature on titanium oxynitride thin films prepared by reactive sputtering10.1016/j.apsusc.2003.09.028 ↗
61. Structural properties of ultrathin amorphous silicon oxynitride layers10.1143/JJAP.42.3570 ↗