Effect of Mo content on the corrosion and tribocorrosion behavior of CoCrFeNiMox HEA coatings in simulated seawater
Source abstract
Abstract
This study investigates the influence of Mo content on the adhesion, electrochemical, and tribocorrosion behavior of CoCrFeNiMox (x = 0-20 at.%) high-entropy alloy (HEA) coatings deposited by high power impulse magnetron sputtering (HiPIMS) on AISI 304 stainless steel. Electrochemical analyses demonstrate that the HEA coatings exhibit superior corrosion resistance compared to stainless steel, with corrosion current densities reduced by approximately one order of magnitude in 3.5 wt.% NaCl solution, although no clear dependence on Mo content is observed. In contrast, tribocorrosion performance strongly depends on composition: coatings with low Mo contents (0-5 at.%) exhibit the lowest specific wear rates (45-61 × 10−6 mm3/(N·m)), outperforming AISI 304 (108 × 10-6 mm3/(N·m)), whereas Mo-rich coatings (> 10 at.%) undergo premature wear-through and delamination. This trend is further supported by scratch test results, which indicate a reduction in adhesion toughness for Mo contents above ~10 at.%, with the critical load for coating failure decreasing from ~34 N (Mo10) to ~14 N (Mo15). This behavior is likely attributed to the increased brittleness associated with the formation of a hard body-centered cubic (BCC) phase within the face-centered cubic (FCC) matrix at high Mo contents. Overall, these results highlight the need for careful compositional optimization of Mo-doped HEA coatings, with low-Mo compositions providing the best balance between corrosion resistance, adhesion, and tribocorrosion performance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · Metal and Thin Film Mechanics · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Wear-accelerated corrosion of passive metals in tribocorrosion systems10.1149/1.1838341 ↗
2. Tribo-corrosion of coatings: a review10.1088/0022-3727/40/18/S10 ↗
3. Tribocorrosion behaviors of multilayer PVD DLC coated 304L stainless steel in seawater10.1016/j.diamond.2017.09.002 ↗
4. High-entropy alloy for thin film application: a review10.3390/coatings12121842 ↗
5. Corrosion-resistant high-entropy alloys: a review10.3390/met7020043 ↗
6. A comparative study on the tribocorrosion behaviors of AlFeCrNiMo high entropy alloy coatings and 304 stainless steel
7. Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
8. Microstructural development in equiatomic multicomponent alloys10.1016/j.msea.2003.10.257 ↗
9. Microstructures and properties of high-entropy alloys10.1016/j.pmatsci.2013.10.001 ↗
10. Fatigue behavior of Al0.5CoCrCuFeNi high entropy alloys10.1016/j.actamat.2012.06.046 ↗
11. High entropy alloys: a focused review of mechanical properties and deformation mechanisms10.1016/j.actamat.2019.12.015 ↗
12. Recent advances in tribology of high entropy alloys: A critical review10.1016/j.pmatsci.2023.101106 ↗
13. A review on fundamental of high entropy alloys with promising high–temperature properties10.1016/j.jallcom.2018.05.067 ↗
14. High-entropy alloys as a platform for catalysis: progress, challenges, and opportunities10.1021/acscatal.0c03617 ↗
15. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
16. Microstructure and properties of high-entropy AlxCoCrFe2.7MoNi alloy coatings prepared by laser cladding10.3390/met9121243 ↗
17. Microstructure and Properties of CoCrFeNiTi High-Entropy Alloy Coating Fabricated by Laser Cladding10.1007/s11665-020-05204-y ↗
18. Microstructure and mechanical properties of multiprincipal component CoCrFeNiMox alloys10.1016/j.matchar.2012.05.005 ↗
19. Ductile CoCrFeNiMox high entropy alloys strengthened by hard intermetallic phases10.1016/j.actamat.2016.06.063 ↗
20. Strengthening FCC-CoCrFeMnNi high entropy alloys by Mo addition10.1016/j.jmst.2018.10.009 ↗
21. Effect of Mo element on the mechanical properties and tribological responses of CoCrFeNiMox high-entropy alloys
22. The effect of molybdenum on the corrosion behaviour of the high-entropy alloys Co1.5CrFeNi1.5Ti0.5Mox in aqueous environments10.1016/j.corsci.2010.04.004 ↗
23. Effect of Mo addition on corrosion behavior of high-entropy alloys CoCrFeNiMox in aqueous environments10.1007/s40195-018-0812-7 ↗
24. Effect of molybdenum content on the microstructure and corrosion behavior of FeCoCrNiMox high-entropy alloys10.1016/j.jmst.2019.10.020 ↗
25. Evolution in microstructure, wear, corrosion, and tribocorrosion behavior of Mo-containing high-entropy alloy coatings fabricated by laser cladding10.1016/j.corsci.2021.109727 ↗
26. CoCrFeNi(W1−xMox) high-entropy alloy coatings with excellent mechanical properties and corrosion resistance prepared by mechanical alloying and hot pressing sintering10.1016/j.matdes.2016.12.076 ↗
27. A novel pulsed magnetron sputter technique utilizing very high target power densities10.1016/S0257-8972(99)00292-3 ↗
28. Ti1−xAlxN coatings by Reactive High Power Impulse Magnetron Sputtering: film/substrate interface effect on residual stress and high temperature oxidation10.1016/j.surfcoat.2018.09.004 ↗
29. Synthesis and characterization of super-hard AlCrTiVZr high-entropy alloy nitride films deposited by HiPIMS10.1016/j.apsusc.2020.146529 ↗
30. Spatial electron density distribution in a high-power pulsed magnetron discharge10.1109/TPS.2005.845022 ↗
31. Plasma dynamics in a highly ionized pulsed magnetron discharge10.1088/0963-0252/14/3/015 ↗
32. Powder metallurgy route for the synthesis of multiprincipal element alloys sputtering targets10.1002/adem.202101518 ↗
33. In-house synthesis of CoCrFeNi ingots using an electric furnace10.1016/j.matlet.2022.132571 ↗
34. Complex structure/composition relationship in thin films of AlCoCrCuFeNi high entropy alloy10.1016/j.matchemphys.2009.05.025 ↗
35. Thermal stability of AlCoCrCuFeNi high entropy alloy thin films studied by in-situ XRD analysis10.1016/j.surfcoat.2009.12.006 ↗
36. Effect of Mo content on the microstructure and mechanical properties of CoCrFeNiMox HEA coatings deposited by high power impulse magnetron sputtering10.1016/j.surfcoat.2023.130244 ↗
37. International Organization for Standardization · 2005
38. Contact and rubbing of flat surfaces10.1063/1.1721448 ↗
39. Contact of nominally flat surfaces
40. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour10.1016/S0043-1648(00)00488-9 ↗
41. The structure and mechanical and tribological properties of TiBCN nanocomposite coatings10.1016/j.actamat.2009.10.063 ↗
42. Nanoindentation and nanoscratching of hard carbon coatings for magnetic disks10.1557/PROC-383-447 ↗
43. Relationships between hardness, Young’s modulus and elastic recovery in hard nanocomposite coatings10.1016/S0257-8972(01)01714-5 ↗
44. Plasticity characteristic obtained by indentation10.1088/0022-3727/41/7/074013 ↗
45. Improvement of ‘duplex’ PVD coatings for HSS cutting tools by ion mixing10.1016/j.surfcoat.2004.02.015 ↗
46. Elastic modulus and hardness of plasma-polymerized organosilicones evaluated by nanoindentation techniques10.1002/ppap.201500036 ↗
47. The relationship between hardness and scratch adhession10.1016/0040-6090(87)90382-8 ↗
48. Failure modes in scratch adhesion testing10.1016/0257-8972(91)90188-3 ↗
49. A review on the mechanical methods for evaluating coating adhesion10.1007/s00707-013-0979-y ↗
50. Synthesis of AlxCoCrFeNi HEA thin films by high power impulse magnetron sputtering: effect of substrate bias voltage10.1016/j.surfcoat.2024.131644 ↗
51. Effect of molybdenum additives on corrosion behavior of (CoCrFeNi)100−xMox high-entropy alloys10.3390/e20120908 ↗
52. Microstructural evolution, mechanical and corrosion behaviors of as-annealed CoCrFeNiMox (x = 0, 0.2, 0.5, 0.8, 1) high entropy alloys10.1016/j.jallcom.2019.153273 ↗
53. Insights into the mechanism of Mo protecting CoCrFeNi HEA from pitting corrosion—a quantitative modelling study on passivation and repassivation processes10.1016/j.jmst.2023.09.032 ↗
54. Influence of Mo on the Microstructure and Corrosion Behavior of Laser Cladding FeCoCrNi High-Entropy Alloy Coatings
55. High-throughput synthesis and corrosion behavior of sputter-deposited nanocrystalline Alx(CoCrFeNi)100-x combinatorial high-entropy alloys10.1016/j.matdes.2020.109018 ↗
56. Effect of crystal structure and grain size on corrosion properties of AlCoCrFeNi high entropy alloy10.1016/j.jallcom.2020.158056 ↗
57. Solid-solution CrCoCuFeNi high-entropy alloy thin films synthesized by sputter deposition10.1080/21663831.2015.1048904 ↗
58. Celis · 2017
59. Electrochemical techniques for studying tribocorrosion processes10.1016/S0043-1648(03)00556-8 ↗
60. Dry sliding and tribocorrosion behaviour of hot pressed CoCrMo biomedical alloy as compared with the cast CoCrMo and Ti6Al4V alloys10.1016/j.matdes.2013.05.032 ↗
61. Synthesis and microstructure of the (Co,Cr,Fe,Mn,Ni)3O4 high entropy oxide characterized by spinel structure10.1016/j.matlet.2017.12.148 ↗
62. Elastic and plastic work of indentation as a characteristic of wear behavior for cutting tools with nitride PVD coatings10.1016/j.tsf.2004.07.038 ↗