Electrodeposition of REACH compliant boron carbide reinforced nickel composites for wear protection
Source abstract
Abstract
Due to European regulations like REACH, hard chromium plating is gradually being replaced with other, more environmentally friendly, procedures. Nickel-based nanocomposite coatings, obtained by co-deposition of nanoparticles (NPs) of different nature (typically hard ceramics) within nickel matrix, are considered a practical alternative to hard chromium. However, to operate with a nickel REACH compliant electrolyte, boric acid must be replaced. In this study, boric acid was substituted with succinic acid to operate in line with the constraints of REACH regulation. The REACH compliant nickel electrolyte was tested, demonstrating the buffering capacity of succinic acid and its ability to produce bright and uniform nickel coatings in a wide range of current densities (10–60 mA/cm 2 ), even though the new formulation caused an increase of the mean grain size and a subsequent decrease of hardness. Moreover, boron carbide was added to the solution in different concentrations (1, 2, 3.5, 5 and 10 g/L) in order to study the effect on hardness and tribological properties such as the coefficient of friction in relation to the content of B 4 C inside the coating. The tribological properties of the composite coatings were assessed by modified ASTM G75 , mini traction machine (MTM) and Basalt N2 tests. The hardness increased up to values of 1215 HV 0.1 with a concentration of boron carbide in the coating up to 2.71 wt% for the samples produced with a concentration of 10 g/L of nanoparticles in the bath. Furthermore, the same sample exhibited a constant coefficient of friction of 0.12 for more than 100 cycles. • A commercial nickel electrolyte is modified to make it REACH compliant. • Succinic acid is proposed as REACH compliant buffer for nickel composite plating. • A nickel/B 4 C hard composite is deposited without boric acid for the first time. • The obtained hardness exceeds 1215 HV 100 . • Tribological properties of the composite support its use as anti-wear coating.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electrodeposition and Electroless Coatings · Tribology and Wear Analysis · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Alternative tribological coatings to electrodeposited hard chromium: a critical review10.1080/00202967.2020.1776962 ↗
2. 2007
3. European Parliament · 2006
4. European Chemical Agency
5. Review of nickel-based electrodeposited tribo-coatings10.1007/s12666-017-1175-x ↗
6. Recent trends and developments in two-dimensional materials based electrodeposited nickel nanocomposite coatings10.1016/j.flatc.2022.100434 ↗
7. Wear and tribological characterization of nickel matrix electrodeposited composites: a review
8. A review on mechanical, tribological and electrochemical performance of ceramic particle-reinforced Ni-based electrodeposited composite coatings10.1007/s10853-022-07809-1 ↗
9. Hall-Petch relations and strengthening of Al-ZnO composites in view of grain size relative to interparticle spacing10.1016/j.scriptamat.2018.04.042 ↗
10. Synthesis, characterization and comparison of sediment electro-codeposited nickel–micro and nano SiC composites10.1016/j.apsusc.2011.08.038 ↗
11. Codeposition of nickel–phosphorus alloys reinforced with boron carbide microparticles: direct and pulse plating10.1080/00202967.2017.1263477 ↗
12. European Chemical Agency
13. Nickel electroplating bath using citric acid10.4139/sfj.52.462 ↗
14. Properties of the film from nickel electroplating bath using citric acid10.4139/sfj.53.335 ↗
15. Effect of bath pH on nickel citrate electroplating bath10.1016/S0026-0576(04)82610-2 ↗
16. Citrate-based baths for electrodeposition of nanocrystalline nickel coatings with enhanced hardness10.1016/j.jallcom.2020.156857 ↗
17. Comparison of the environmental impact of the conventional nickel electroplating and the new nickel electroplating10.1007/s11367-017-1375-y ↗
18. The electrochemical deposition of nickel from electrolytes containing malonic acid10.1016/S0257-8972(01)01518-3 ↗
19. Boric acid free nickel electrolyte for plating of electrical contacts10.1080/00202967.2016.1268841 ↗
20. Electrodeposition of nickel and composite nickel-fullerenol coatings from low-temperature sulphate-chloride-isobutyrate electrolyte10.1016/j.proche.2014.10.063 ↗
21. European Union
22. European Chemicals Agency
23. The Scherrer formula for X-ray particle size determination10.1103/PhysRev.56.978 ↗
24. ASTM G75-95 · 1995
25. A contribution to the surface analysis and characterisation of HVOF coatings for petrochemical application10.1016/S0043-1648(01)00621-4 ↗
26. The influence of slide–roll ratio on ZDDP tribofilm formation10.1007/s11249-016-0738-z ↗
27. The role of migration mass transfer in the electrodeposition of nickel from sulfate-chloride and chloride solutions containing succinic acid10.1134/S1023193508030099 ↗
28. Electrochemical nucleation and growth of Zn-Ni alloys from chloride citrate-based electrolyte10.1016/j.jelechem.2019.113261 ↗
29. Budi · Electrodeposition of nickel-nitride composite coating: effects of boric acid on structure and mechanical properties · 2019
30. Texture orientation, morphology and performance of nanocrystalline nickel coatings electrodeposited from a Watts-type bath: effects of H3BO3 concentration and plating time10.1016/j.surfcoat.2021.127648 ↗
31. Kinetics of the deposition of inert particles from electrolytic baths10.1149/1.2404383 ↗
32. Boron carbide: structure, properties, and stability under stress10.1111/j.1551-2916.2011.04865.x ↗
33. State of art review on nickel-based electroless coatings and materials
34. A review on the nickel based metal matrix composite coating10.1007/s12540-020-00872-w ↗
35. Effects of boron carbide particle content on corrosion resistance and wear resistance of Ni-B/B4C composite coatings10.20964/2022.11.61 ↗
36. Mechanical properties and corrosion resistance of pulse electrodeposited Ni-B/B4C composite coatings10.1016/j.surfcoat.2021.127458 ↗
37. Fabrication of Ni-W-B4C composite coatings and evaluation of its micro-hardness and corrosion resistance properties10.1016/j.ceramint.2018.02.128 ↗
38. Effect of boron carbide reinforcement on surface properties of electroless Ni–B and Ni–B–W coatings10.1016/j.matchemphys.2023.127899 ↗
39. Mathematical modeling of Ni/SiC co-deposition in the presence of a cationic dispersant10.1149/2.052309jes ↗
40. Deviations from hall-petch behaviour in as-prepared nanocrystalline nickel10.1016/0956-716X(92)90596-7 ↗
41. Hall–Petch relationship in nanocrystalline Ni and Be–B alloys10.1016/j.intermet.2004.07.029 ↗
42. Microstructure development and nanoindentation behaviour of annealed Ni-P-Ti coatings10.1080/02670844.2020.1794212 ↗
43. Tribological performance of Mn3(PO4)2 coating and PC/MoS2 coating in Rolling–Sliding and pure sliding contacts with gear oil10.1016/j.triboint.2020.106642 ↗
44. Influence of BN and B 4 C particulates on wear and corrosion resistance of electroplated nickel matrix composite coatings10.1179/1751584X15Y.0000000007 ↗