journal article·2026-03Open access

Thermal stability and tribological properties of HiPIMS Cr2O3 coatings with varied pulse widths

Jiale Weng, Zhiqiang Ye, Yu X. Xu, Dongsen Geng, Qimin Wang

Abstract

Wear-resistant oxide coatings play an important role in protecting the surfaces of tools and components. The fabrication of hard oxides using advanced physical vapor deposition techniques has recently attracted considerable attention. In this work, Cr 2 O 3 coatings, with a Cr transition layer, were deposited by high-power impulse magnetron sputtering at different pulse widths, and their structure, thermal stability, and tribological properties were investigated. All Cr 2 O 3 coatings demonstrate columnar grain growth with a thermodynamically stable hexagonal structure. A pulse width of 70 μs at a constant frequency of 500 Hz yields a peak current of 500 A, resulting in a hardness of 27.2 GPa, which is superior to that achieved at 100 and 280 μs. Decreasing the pulse width to 35 μs at 1500 Hz gives rise to a maximum hardness of 29.3 GPa. The hardness of Cr 2 O 3 coatingsincreases upon annealing in air at 800 and 900 °C. Notable grain coarsening, along with increased porosity, leads to a decrease in hardness at 1000 and 1100 °C. The hardness at 1100 °C decreased by 3.5 to 4.7 GPa compared to that at 900 °C. The friction coefficients of the examined Cr 2 O 3 range from 0.32 to 0.36 at ambient temperature and diminish to 0.26 to 0.28 at 600 °C. At ambient temperature, Cr 2 O 3 coatings, including that deposited at a high pulse width of 280 μs, show outstanding wear resistance, with the specific wear rate below 2 × 10 −7 mm 3 /N∙m. Nonetheless, certain coatings exhibit severe localized wear at 600 °C, with cracking inside wear tracks. This reduced wear resistance is likely attributable to the inherent brittleness of Cr 2 O 3 and the inconsistency in deformation with the underlying Cr.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Thermal Expansion and Ionic Conductivity · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Chromium oxide coatings applied to magnetic tape heads for improved wear resistance10.1016/S0301-679X(02)00214-1 ↗
2. Effect of plasma nitriding and modulation structure on the adhesion and corrosion resistance of CrN/Cr2O3 coatings10.1016/j.surfcoat.2019.125051 ↗
3. Corrosion and tribological behaviors of chromium oxide coatings prepared by the glow-discharge plasma technique10.1016/j.surfcoat.2009.06.020 ↗
4. The role of oxygen on anisotropy in chromium oxide hard mask etching for sub-micron fabrication10.1109/TNANO.2020.3038737 ↗
5. Review of physical vapor deposited (PVD) spectrally selective coatings for mid- and high-temperature solar thermal applications10.1016/j.solmat.2011.10.028 ↗
6. Quo vadis thermal spraying?10.1361/105996301770349510 ↗
7. Plasma enhanced chemical vapor deposition of Cr2O3 thin films using chromium hexacarbonyl (Cr(CO)6) precursor10.1016/j.tsf.2008.02.027 ↗
8. Microstructures and mechanical properties of chromium oxide films by arc ion plating10.1016/j.matlet.2003.12.029 ↗
9. Study on nanocrystalline Cr2O3 films deposited by arc ion plating: II. mechanical and tribological properties10.1016/j.surfcoat.2011.10.026 ↗
10. Influence of oxygen addition on the structure, mechanical and thermal properties of CrN coating10.1016/j.surfcoat.2021.126992 ↗
11. Comparative study on mechanical and tribological properties of Cr–Al–N and Cr–Al–O coatings deposited by cathodic arc evaporation10.1016/j.triboint.2022.107989 ↗
12. Development of r.f. sputtered chromium oxide coating for wear application10.1016/0040-6090(79)90515-7 ↗
13. The effect of deposition parameters on the structure and mechanical properties of chromium oxide coatings deposited by reactive magnetron sputtering10.3390/coatings8030111 ↗
14. Role of deposition parameters on microstructure and mechanical properties of chromium oxide coatings10.1016/j.surfcoat.2007.04.066 ↗
15. Growth and characterization of chromium oxide coatings prepared by pulsed-direct current reactive unbalanced magnetron sputtering10.1016/j.apsusc.2008.08.057 ↗
16. Characterization of sputter-deposited chromium oxide thin films10.1016/S0257-8972(99)00384-9 ↗
17. Texture and microstructure of Cr2O3 and (Cr,Al)2O3 thin films deposited by reactive inductively coupled plasma magnetron sputtering10.1016/j.tsf.2010.01.008 ↗
18. Study on chromium oxide synthesized by unbalanced magnetron sputtering10.1016/S0040-6090(98)01266-8 ↗
19. A review comparing cathodic arcs and high power impulse magnetron sputtering (HiPIMS)10.1016/j.surfcoat.2014.08.043 ↗
20. Industrial application potential of high power impulse magnetron sputtering for wear and corrosion protection coatings10.1063/5.0159292 ↗
21. High power pulsed magnetron sputtering: a review on scientific and engineering state of the art10.1016/j.surfcoat.2009.11.013 ↗
22. Ionization of sputtered metals in high power pulsed magnetron sputtering10.1116/1.1818135 ↗
23. Hybrid deposition of Cr–O/Al–O hard coatings combining cathodic arc evaporation and high power impulse magnetron sputtering10.1016/j.surfcoat.2023.129235 ↗
24. High deposition rate films prepared by reactive HiPIMS10.1016/j.vacuum.2021.110329 ↗
25. High rate reactive sputtering of Al2O3 coatings by HiPIMS10.1016/j.surfcoat.2018.10.024 ↗
26. Structure and properties of Cr2O3 coatings deposited using DCMS, PDCMS, and DOMS10.1016/j.surfcoat.2015.06.044 ↗
27. Microstructures and electrical properties of nanostructured Cr2O3 thin films deposited by dual-target reactive high-power impulse magnetron sputtering10.1016/j.vacuum.2019.03.035 ↗
28. Deposition of titanium oxide films by reactive High Power Impulse Magnetron Sputtering (HiPIMS): influence of the peak current value on the transition from metallic to poisoned regimes10.1016/j.surfcoat.2012.02.034 ↗
29. On the relationship between the peak target current and the morphology of chromium nitride thin films deposited by reactive high power pulsed magnetron sputtering10.1088/0022-3727/42/1/015304 ↗
30. Effect of peak current on the microstructure, mechanical properties and tribological behavior of MoxN coatings deposited by high power impulse magnetron sputtering10.1016/j.triboint.2023.108955 ↗
31. Influence of Ag additions on the structure, mechanical properties and oxidation behaviour of Cr-O coatings deposited by HiPIMS10.1016/j.surfcoat.2018.02.025 ↗
32. In situ lift-out dedicated techniques using FIB–SEM system for TEM specimen preparation10.1016/j.micron.2012.05.006 ↗
33. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
34. CrN thin films deposited by HiPIMS in DOMS mode10.1016/j.surfcoat.2016.02.064 ↗
35. Target material pathways model for high power pulsed magnetron sputteringa10.1116/1.1865133 ↗
36. Gas density reduction effects in magnetrons10.1116/1.574988 ↗
37. On the nature of running-in10.1016/j.triboint.2005.07.020 ↗
38. Friction and wear properties of plasma-sprayed Cr2O3–BaCrO4 coating at elevated temperatures10.1016/j.ceramint.2021.12.081 ↗
39. Flash temperature measurement during dry friction process at high sliding speed10.1016/j.wear.2010.01.019 ↗
40. Effect of N2 to total pressure ratio on the structure, mechanical and tribological properties of magnetron-sputtered Ti-Al-Ta-Si-N coatings10.1016/j.surfcoat.2024.131198 ↗