journal article·2026-03Open access

Mechanisms of deposit formation in injection moulding cavities and the role of tool coatings and internal release agents

Kai Lingnau, Chantal Theile-Rasche, Klaus Vissing, Elmar Moritzer, Guido Grundmeier, Martin Wiesing

Abstract

A major challenge in the injection moulding industry is the formation of tool build-up and the formation of deposits. Current solutions include the use of hard coatings paired with low surface energy finishes, e.g. sol-gel coats or PTFE-based polishes, so that there is a need for more durable, scratch-resistant and PTFE-free coating solutions. Aside this technological deficit, there is also a deep lack of knowledge about the functioning principles of tool coatings and their influence on the formation of deposits. We therefore introduced low surface energy coatings deposited by plasma-enhanced physical vapour deposition (PE-CVD), which enable to tailor hardness, Young's modulus and surface energy in a wide range. The interactions between such coatings and molten polycarbonate (PC) were analysed to test their stability against the harsh conditions of injection moulding and to reveal the fundamental mechanisms of deposit formation. We found that interfacial chemical reactions cause deposit formation in the case of the bare steel, which were avoided by the PE-CVD coatings in presence of the internal release agents in Makrolon 2405.The PE-CVD coatings therefore shifted the interactions into a regime where deposits were formed by wetting instead. The synergism of internal release agents and PE-CVD coatings was studied in a model system consisting of polycarbonate and pentaerythritol tetrastearate (PETS) with varying degree of esterification (hydroxyl value). The results disclosed that the role of the release agent is limited to interact predominantly with the polymer surface and to decrease its surface energy in presence of the PE-CVD coating, because of the lower surface energy of the latter. However, the formation of a low-molecular weight weak boundary layer could not be prevented by the PE-CVD coating. This motivated to discuss the thermodynamical foundations of the observed wetting of the deposits using basic wetting theory. It was highlighted that matching the surface energy of a coating to the base polymer in a compound removes uncompensated interfacial energies so that deposits stay formally dispersed. This notion correlated with the observed reduction of deposits by the PE-CVD coatings and internal release agents and provides therefore an explanation of their functioning. Finally, we discussed the concept that an ideal surface technological solution shall decrease the interfacial energies to avoid deposits but may also decrease the individual surface energies to lower adhesion.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Injection Molding Process and Properties · Metal and Thin Film Mechanics · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Advanced injection molding methods: review10.3390/ma16175802 ↗
2. Recent progress in milling operations for injection mould hardened tool steels: a concise review10.1007/s00170-025-16951-4 ↗
3. Improving the wear resistance of moulds for the injection of glass fibre–reinforced plastics using PVD coatings: a comparative study10.3390/coatings7020028 ↗
4. Texturing technologies for plastics injection molding: a review10.3390/mi13081211 ↗
5. Manufacturing of micro-structured PVD hard coated molds and their potential use in plastic injection molding of micro-structured surfaces: a state-of-the-art review10.1007/s00170-025-17304-x ↗
6. Whelan · 2024
7. Belag und Entformung analysieren
8. Dahlmann · 2024
9. Sonnenberg · 2018
10. Analysis of the inhibition of thermal degradation of molten polycarbonate at tool steel interfaces by thin TiAlN coatings10.1016/j.polymdegradstab.2017.07.013 ↗
11. Application of advanced surface treatment technologies in the modern plastics moulding industry10.1016/S0043-1648(96)07503-5 ↗
12. Characterization of mold fouling during elastomer injection molding10.1002/app.24450 ↗
13. Thin films of MoN, WN, and perfluorinated silane deposited from dimethylamido precursors as contamination resistant coatings on micro-injection mold inserts10.1016/j.surfcoat.2008.05.007 ↗
14. Advances in the design and manufacturing of novel freeform optics
15. Vissing · 2026
16. Long-term analysis of surface coatings for their wear resistance in the injection molding process
17. Naumkin · 2023
18. Impact of improved phosphite hydrolytic stability on the processing stabilization of polypropylene10.1002/vnl.20052 ↗
19. Beamson · 2012
20. Serini · 2024
21. Development of a methodology for XPS curve-fitting of the Si 2p core level of siloxane materials10.1002/sia.1917 ↗
22. The thermal degradation of polysiloxanes—I. poly(dimethylsiloxane)10.1016/0014-3057(78)90084-8 ↗
23. Mechanical properties of homopolymer interfaces: transition from simple pullout to crazing with increasing interfacial width10.1021/ma980860o ↗
24. Efficient disentanglement of polycarbonate melts under complex shear field10.1016/j.polymer.2020.122610 ↗
25. Thermally degradative oligomerization of polycarbonate in fatty oil
26. Surface free energy of polypropylene and polycarbonate solidifying at different solid surfaces10.1016/j.apsusc.2009.09.024 ↗
27. Permanente plasmapolymere Trennschichten10.1002/vipr.200600275 ↗
28. Interfacial interactions between self-associated polar liquids and squalane used to test equations for solid—liquid interfacial interactions10.1016/0166-6622(90)80298-I ↗
29. Estimation of the surface free energy of polymers10.1002/app.1969.070130815 ↗
30. Tailoring the attraction of polymers toward surfaces10.1021/acs.macromol.9b00492 ↗
31. Historical review of die drool phenomenon in plastics extrusion10.1080/15583724.2013.860987 ↗
32. Die drool theory10.1515/polyeng-2012-0044 ↗
33. Temperature transitions on the surface of a thermoplastic melt during injection moulding and its use for chemical reactions10.1016/j.ijheatmasstransfer.2012.06.096 ↗