journal article·2026-05Open access

Load-and time-dependent dry tribological behavior of quench-produced diamond coatings on commercially pure titanium

Mahmoud Talaat Youssef, Ahmed Hamed Oraby, Tomohiro Yoshida, Hiroshi Naragino, Tsuyoshi Yoshitake, Abdelrahman Zkria Ahmed

Abstract

Titanium and its alloys are extensively employed in biomedical implant applications owing to their excellent biocompatibility and corrosion resistance; however, their inherently poor tribological performance severely limits long-term reliability under load-bearing conditions. In this work, a highly adherent Quench-produced Diamond (Q-Dia) coating was deposited on commercially pure titanium using a hybrid coaxial arc plasma deposition (CAPD) technique combined with in situ Ar + plasma etching to enhance interfacial bonding. The resulting coating exhibits a dense nanocomposite architecture comprising nanodiamond crystallites embedded within an amorphous carbon matrix, which promotes strong coating–substrate adhesion, as evidenced by a high critical load (Lc₂) of 20.13 N determined from scratch testing. Dry sliding tribological tests against an Al₂O₃ counter-body revealed a substantial reduction in friction and wear compared with uncoated titanium. While bare titanium showed high and unstable coefficients of friction (0.497–0.567) accompanied by severe wear damage, the Q-Dia-coated surface achieved a low and stable steady-state friction coefficient of approximately 0.127 with no wear observed. Furthermore, electrochemical measurements conducted in simulated body fluid demonstrated a positively shifted corrosion potential for the Q-Dia coating (0.025 V ) relative to bare titanium (−0.324 V), indicating improved electrochemical stability. These findings demonstrate that Q-Dia coatings effectively mitigate the tribological limitations of titanium without compromising corrosion resistance, highlighting their strong potential for load-bearing biomedical implant applications operating under dry or boundary-lubricated conditions. • Hybrid CAPD enables room-temperature deposition of highly adherent (~3 μm) Q-Dia coatings on titanium. • Scratch testing reveals strong coating–substrate adhesion, with a high critical load of Lc₂ = 20.13 N. • Q-Dia coatings markedly enhance the tribological performance of pure titanium under dry sliding against Al₂O₃. • Extremely low steady-state friction coefficients down to 0.127 are achieved. • Superior wear resistance arises from a stable, carbon-rich tribo-layer formed via localized sp 3 -to-sp 2 rehybridization.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Diamond and Carbon-based Materials Research · Metal and Thin Film Mechanics · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. Failure rates of stemmed metal-on-metal hip replacements: analysis of data from the National Joint Registry of England and Wales10.1016/S0140-6736(12)60353-5 ↗
2. A comparative review of osseointegration failure between osseointegrated bone conduction device models in pediatric patients10.1097/MAO.0000000000000970 ↗
3. Projections of primary and revision hip and knee arthroplasty in the United States from 2005 to 203010.2106/00004623-200704000-00012 ↗
4. Incidence and risk factors of in-hospital prosthesis-related complications following total hip arthroplasty: a retrospective Nationwide inpatient sample database study10.1007/s00264-020-04682-y ↗
5. DLC coatings in biomedical applications – review on current advantages, existing challenges, and future directions10.1016/j.surfcoat.2024.131006 ↗
6. Enhanced tribological and corrosion properties of multilayer ta-C films via alternating sp3 content10.1016/j.surfcoat.2019.05.087 ↗
7. Influences of Ti, Al and V metal doping on the structural, mechanical and tribological properties of DLC films10.1016/j.diamond.2021.108639 ↗
8. Effect of textured DLC coatings on tribological properties of titanium alloy under grease lubrication10.1088/2053-1591/ab9ced ↗
9. Effect of sp3 content on adhesion and tribological properties of non-hydrogenated DLC films
10. Low-friction of ta-C coatings paired with Brass and other materials under vacuum and atmospheric conditions10.3390/ma15072534 ↗
11. Influences of different temperatures on the mechanical properties and wear resistance against Ti6Al4V of Ti doped diamond-like carbon deposited on cemented carbide10.1016/j.vacuum.2021.110279 ↗
12. Tribological behavior and machining performance of non-hydrogenated diamond-like carbon coating tested against Ti-6Al-4V: effect of surface passivation by ethanol10.1016/j.surfcoat.2014.06.066 ↗
13. Synergistic effects of optimal negative bias-enhanced growth of quenched-produced diamond films on titanium substrates10.35848/1882-0786/acdfb7 ↗
14. Structural and physical characteristics of ultrananocrystalline diamond/hydrogenated amorphous carbon composite films deposited using a coaxial arc plasma gun10.1143/JJAP.49.015503 ↗
15. Optical emission spectroscopy of deposition process of ultrananocrystalline diamond/hydrogenated amorphous carbon composite films by using a coaxial arc plasma gun10.1016/j.diamond.2010.02.019 ↗
16. Optical and structural characterization of ultrananocrystalline diamond/hydrogenated amorphous carbon composite films deposited via coaxial arc plasma10.1016/j.cap.2018.11.012 ↗
17. Nanoparticle catalyst preparation using pulsed arc plasma deposition10.1039/C5CY00636H ↗
18. Effects of nitrogen doping on the electrical conductivity and optical absorption of ultrananocrystalline diamond/hydrogenated amorphous carbon films prepared by coaxial arc plasma deposition10.7567/JJAP.55.07LE01 ↗
19. Impedance spectroscopy analysis of n-type (nitrogen-doped) ultrananocrystalline diamond/p-type Si heterojunction diodes10.1088/1402-4896/aba97e ↗
20. Synthesis and mechanical wear studies of ultra smooth nanostructured diamond (USND) coatings deposited by microwave plasma chemical vapor deposition with he/H2/CH4/N2 mixtures10.1016/j.diamond.2007.08.041 ↗
21. Diamond-like carbon coatings enhance the hardness and resilience of bearing surfaces for use in joint arthroplasty10.1016/j.actbio.2009.10.037 ↗
22. Fabrication of nitrogen-doped quenched-produced diamond electrodes on titanium substrates by coaxial arc plasma deposition10.1080/26941112.2024.2418587 ↗
23. Tribological performance of quenched diamond coatings on pure titanium under dry sliding conditions10.1016/j.matlet.2025.139592 ↗
24. Interlayer-assisted growth of quenched-produced diamond coatings on Mg–ca alloys for improved corrosion resistance in sodium chloride solution10.1016/j.jallcom.2025.185888 ↗
25. Adhesion of nanodiamond composite films on Ti substrates at room temperature via hybrid ion etching gun and coaxial arc plasma deposition10.35848/1882-0786/ac99b6 ↗
26. Sustainable thick nanodiamond composite coatings on hard metal: effects of varied discharge energies on tribological performance and corrosion resistance10.1016/j.surfcoat.2025.131844 ↗
27. Smooth diamond-like carbon films prepared by cathodic vacuum arc deposition with large glancing angles10.1016/j.diamond.2023.110672 ↗
28. How useful is SBF in predicting in vivo bone bioactivity?10.1016/j.biomaterials.2006.01.017 ↗
29. Synthesis method for ultrananocrystalline diamond in powder employing a coaxial arc plasma gun10.7567/APEX.8.075101 ↗
30. Correlated electrical conductivities to chemical configurations of Nitrogenated Nanocrystalline diamond films10.3390/nano12050854 ↗
31. Interpretation of the Raman spectra of ultrananocrystalline diamond10.1016/j.diamond.2004.07.012 ↗
32. Laser-induced structure transition of diamond-like carbon coated on cemented carbide and formation of reduced graphene oxide10.1557/mrc.2019.88 ↗
33. Nanocarbon ohmic electrodes fabricated by coaxial arc plasma deposition for phosphorus-doped diamond electronics application10.1063/5.0093470 ↗
34. Effects of substrate temperature and intermediate layer on adhesion, structural and mechanical properties of coaxial arc plasma deposition grown nanodiamond composite films on Si substrates10.1016/j.surfcoat.2021.127185 ↗
35. Origin of the 1150 − cm−1 Raman mode in nanocrystalline diamond
36. Novel conversion annealing pretreatment for improved deposition of diamond coatings onto WC-co cemented carbide10.1016/j.jallcom.2021.162325 ↗
37. Fracture mechanics of microcrystalline/nanocrystalline composited multilayer chemical vapor deposition self-standing diamond films10.1016/j.ceramint.2022.04.173 ↗
38. Synthesis of nanocrystalline diamond embedded diamond-like carbon films on untreated glass substrates at low temperature using (C2H2 + H2) gas composition in microwave plasma CVD10.1016/j.apsusc.2021.152132 ↗
39. Raman spectroscopy of amorphous, nanostructured, diamond-like carbon, and nanodiamond10.1098/rsta.2004.1452 ↗
40. Formation of low resistivity layers on singlecrystalline diamond by excimer laser irradiation10.1016/j.diamond.2019.04.013 ↗
41. Study of CVD diamond layers with amorphous carbon admixture by Raman scattering spectroscopy10.1515/msp-2015-0067 ↗
42. Formation of nanoscale diamond particles without substrate heating by cathodic arc deposition10.1143/JJAP.44.L746 ↗
43. Hard and superhard nanocomposite coatings10.1016/S0257-8972(99)00586-1 ↗
44. Chemical bonding structural analysis of nitrogen-doped ultrananocrystalline diamond/hydrogenated amorphous carbon composite films prepared by coaxial arc plasma deposition10.7567/APEX.10.015801 ↗
45. Comparison between FTIR and XPS characterization of amino acid glycine adsorption onto diamond-like carbon (DLC) and silicon doped DLC10.1016/j.apsusc.2013.02.070 ↗
46. Direct evaluation of the sp3 content in diamond-like-carbon films by XPS10.1016/S0169-4332(98)00319-5 ↗
47. An overview of the potential of quantitative coating adhesion measurement by scratch testing10.1016/j.triboint.2005.04.013 ↗
48. Residual stress and cracking in thin PVD coatings10.1016/S0042-207X(01)00327-X ↗
49. Determination of interfacial fracture toughness of coatings using circumferentially notched cylindrical substrate10.1016/j.msea.2011.09.053 ↗
50. Understanding of fracture conditions and material response in a model TiN film/stainless steel substrate system – a cross-sectional scratch test study10.1016/j.surfcoat.2022.128340 ↗
51. Effect of film gradient profile on adhesion strength, residual stress and effective hardness of functionally graded diamond-like carbon films10.1016/j.apsusc.2014.05.161 ↗
52. Deposition, characterization, and tribological applications of near-frictionless carbon films on glass and ceramic substrates10.1088/0953-8984/18/32/S06 ↗
53. Tribology of diamond-like carbon films: recent progress and future prospects10.1088/0022-3727/39/18/R01 ↗
54. Role of microstructure and structural disorder on tribological properties of polycrystalline diamond films10.1016/j.apsusc.2018.10.265 ↗
55. Tribological and mechanical properties of diamond films synthesized with high methane concentration10.1016/j.ijrmhm.2019.105057 ↗
56. Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning10.1007/s00170-020-05000-x ↗
57. Tribological behavior of hafnium diboride thin films10.1016/j.surfcoat.2006.08.086 ↗
58. Influence of counterbody material and sliding speed on tribological behavior of TiBx coatings10.1016/j.vacuum.2025.114863 ↗
59. Tribological characteristics of amorphous hydrogenated (a-C:H) and tetrahedral (ta-C) diamond-like carbon coating at different test temperatures in the presence of commercial lubricating oil10.1016/j.surfcoat.2014.02.052 ↗
60. Raman analysis of DLC coated engine components with complex shape: understanding wear mechanisms10.1016/j.tsf.2009.09.110 ↗
61. Interpretation of Raman spectra of disordered and amorphous carbon10.1103/PhysRevB.61.14095 ↗
62. A study on the tribological characteristics of duplex-treated Ti–6Al–4V alloy under oil-lubricated sliding conditions10.1016/j.triboint.2013.03.015 ↗
63. Effects of plastic strain of diamond-like carbon coated stainless steel on the corrosion behavior in simulated body fluid environment10.1016/j.surfcoat.2007.09.046 ↗