journal article·2026-07Open access

Effect of strontium aluminate particle incorporation on the corrosion behavior of PEO coatings on AlSi12Cu1(Fe) diecast alloy

Emel Razzouk, Itziar Hidalgo-González, Dániel Koncz-Horváth, Endzhe Matykina, Raúl Arrabal, Tamás István Török

Abstract

Plasma electrolytic oxidation coatings were produced on a High Pressure Die Cast (HPDC) Al Si alloy using two types of electrolytes: a conventional silicate electrolyte (PEO coatings) and a silicate-based suspension electrolyte (PEOp coatings) containing strontium aluminate particles. The PEO process was applied to two types of initial surfaces: as-diecast (PEO-C/PEOp-C) and ground (PEO-G/PEOp-G). Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PDP) were used to evaluate corrosion resistance and behavior in a 3.5 wt% NaCl solution at ambient temperature. The corrosion performance was monitored for up to 168 h of immersion. The results indicated that PEO coatings exhibited better corrosion resistance than PEOp coatings after 168 h of immersion. This behavior is primarily attributed to coating integrity, which plays a critical role in corrosion resistance. The use of suspension electrolyte led to higher instantaneous current density prior to the onset of the soft-sparking regime, which adversely affected the formation of the inner layer. Additionally, after 24 h of immersion, PEOp coatings formed on the as-diecast surfaces exhibited lower impedance values than those formed on ground surfaces. In contrast, PEO coatings maintained relatively stable corrosion performance regardless of the initial surface condition during the entire immersion period. The polarization resistance decreased by about 90% for PEOp-C coatings after 168 h of immersion, while PEO coatings experienced an increase of approximately 36% in polarization resistance for PEO-C coatings. • Composite PEO coatings are produced using SrAl 2 O 4 suspension electrolyte. • Suspension electrolyte modifies discharge behavior during the PEO process. • PEO coatings exhibited more stable impedance after 168 h of immersion. • Corrosion resistance is governed primarily by inner layer integrity. • The high instantaneous current density affects the inner layer microstructure.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Electrodeposition and Electroless Coatings · Corrosion Behavior and Inhibition · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Henley · 2013
2. Kaufman · 2004
3. The effect of Si content on microstructure and mechanical properties of Al–Si alloy
4. 2008 · 15
5. Influence of copper addition in AlSi7MgCu alloy on microstructure development and tensile strength improvement10.3390/met10121623 ↗
6. Influence of cu addition on the heat treatment response of A356 foundry alloy10.1016/j.mtcomm.2019.02.013 ↗
7. Experimental investigation on the effect of microstructure modifiers and heat treatment influence on A356 alloy10.1016/j.matpr.2020.08.719 ↗
8. Effect of Main elements (Zn, Mg and cu) on the microstructure, Castability and mechanical properties of 7xxx series aluminum alloys with Zr and Sc10.1016/j.matchar.2021.111559 ↗
9. Effects of strontium addition on the microstructure and corrosion behavior of A356 aluminum alloy10.1016/j.jallcom.2018.05.341 ↗
10. A parametric study of the relationship between microstructure and Wear resistance of Al–Si alloys10.1016/j.wear.2006.03.043 ↗
11. Effect of Fe and Mn additions on microstructure and Wear properties of spray-deposited Al–20Si alloy10.1016/j.matlet.2004.02.027 ↗
12. Al–Si Alloys, Minor, Major, and impurity elements
13. Impact of under-, peak- and over-ageing on the Wear properties of Si-doped Al-based automotive alloy10.1016/j.matpr.2023.02.006 ↗
14. Zolotorevskiĭ · 2007
15. Effects of physical melt treatments on microstructural evolution and anodizing characteristics of Al–Si casting alloys10.4028/www.scientific.net/MSF.695.243 ↗
16. Characterization of externally solidified crystals in a high-pressure die- cast AlSi10MnMg alloy and their effect on porosities and mechanical properties10.1016/j.jmatprotec.2021.117299 ↗
17. Characterization of high-pressure die-cast hypereutectic Al–Si alloys based on microstructural distribution and fracture morphology10.1016/j.jmst.2018.12.005 ↗
18. Microstructure, eutectic Si distribution, and mechanical properties of Al–6Si–Mg high pressure die castings with long Mold filling distance10.1016/j.jmapro.2025.06.075 ↗
19. Investigating the role of cu, Zr and V on the evolution of microstructure and properties of Al–Si–Mg cast alloys
20. Macro porosity formation: a study in high pressure die casting
21. Microstructure, mechanical properties and die-filling behavior of high-performance die-cast Al–Mg–Si–Mn alloy10.1007/s40195-015-0332-7 ↗
22. Skin solidification during high pressure die casting of Al–11Si–2Cu–1Fe alloy10.1016/S0921-5093(02)00747-5 ↗
23. Effect of microstructure and porosity of AlSi10Mg alloy produced by selective laser melting on the corrosion properties of plasma electrolytic oxidation coatings10.1016/j.surfcoat.2020.126477 ↗
24. AC plasma electrolytic oxidation of additively manufactured and cast AlSi12 alloys10.1016/j.surfcoat.2020.126116 ↗
25. Microstructure effects on anodizing high-silicon Aluminium alloy AlSi12Cu1(Fe) under various surface conditions and power modes10.3390/cryst14040352 ↗
26. Microstructure evolution and high density of Nanotwinned ultrafine Si in hypereutectic Al–Si alloy by laser surface Remelting10.1016/j.matchar.2020.110147 ↗
27. Hard anodizing and plasma electrolytic oxidation of an additively manufactured Al–Si alloy10.1016/j.surfcoat.2021.127339 ↗
28. The differences in the formation mechanism of PEO and CPED composited ceramic coatings on Al–12Si alloy10.1016/j.jallcom.2019.01.333 ↗
29. Plasma electrolytic oxidation treatment of Aluminium and titanium alloys
30. Recent Progress in surface modification of metals coated by plasma electrolytic oxidation: principle, structure, and performance10.1016/j.pmatsci.2020.100735 ↗
31. Dual incorporation of SiO₂ and ZrO₂ nanoparticles into the oxide layer on 6061 Al alloy via plasma electrolytic oxidation: coating structure and corrosion properties10.1016/j.jallcom.2016.11.098 ↗
32. Silicate-based plasma electrolytic oxidation (PEO) coatings with incorporated CeO₂ particles on AM50 magnesium alloy10.1016/j.matdes.2015.07.132 ↗
33. Influence of different Si sources on plasma electrolytic oxidation coating formation, morphology and composition10.1016/j.jallcom.2025.181845 ↗
34. PEO of additively manufactured Al10SiMg alloy: effects of α-Al2O3 particles on energy consumption and wear behavior10.1016/j.jmrt.2024.06.171 ↗
35. In-situ formation of Sr₂SiO₄ composite PEO coatings on HPDC AlSi12Cu1 (Fe) alloy for enhanced Wear resistance and energy efficiency10.1016/j.surfcoat.2025.132790 ↗
36. Particle size influences on the coating microstructure through green Chromia inclusion in plasma electrolytic oxidation10.1021/acsami.7b03113 ↗
37. The incorporation of particles suspended in the electrolyte into plasma electrolytic oxidation coatings on Ti and Al substrates
38. Insights into plasma electrolytic oxidation treatment with particle addition10.1016/j.corsci.2015.09.016 ↗
39. Production of phosphorescent coatings on 6082 aluminum using Sr0.95Eu0.02Dy0.03Al₂O₄-δ powder and plasma electrolytic oxidation10.3390/coatings9120865 ↗
40. Novel method of phosphorescent strontium aluminate coating preparation on aluminum10.1016/j.matdes.2018.10.021 ↗
41. Influence of silicon morphology on direct current plasma electrolytic oxidation process in AlSi10Mg alloy produced with laser powder bed fusion10.1038/s41598-022-18176-x ↗
42. Plasma electrolytic oxidation coatings for additively manufactured AlSi7Mg0.6 alloy: unveiling the influence of surface morphology10.1016/j.electacta.2026.148637 ↗
43. Corrosion behavior analysis and plasma electrolytic oxidation coatings protection study of selective laser melting–AlSi10Mg alloy10.1016/j.surfcoat.2025.132753 ↗
44. Unveiling the role of SiC particle reinforcement on aluminum matrix composites surface: insights into PEO coating growth, electrical insulation, and corrosion resistance10.1016/j.ceramint.2025.04.326 ↗
45. Si3N4 reinforced Al-Si-Mg matrix composites: powder metallurgy fabrication, PEO coating and characterization10.1016/j.apsusc.2025.162622 ↗
46. In-situ incorporation of Ce-zeolite during soft sparking plasma electrolytic oxidation10.1016/j.jmrt.2024.04.011 ↗
47. Influence of SiO₂ nanoparticles incorporating into ceramic coatings generated by PEO on Aluminium alloy: morphology, adhesion, corrosion, and Wear resistance
48. Role of anodic precursor layer thickness on PEO coatings: energy consumption and long-term corrosion performance10.1016/j.surfcoat.2023.130186 ↗
49. Effect of different types of glass powders on the corrosion and wear resistance of PEO coatings produced on 6061 aluminum alloy10.1007/s12540-024-01786-7 ↗
50. High performance Tribological coatings on a secondary cast Al–Si alloy generated by plasma electrolytic oxidation10.1016/j.ceramint.2021.07.300 ↗
51. Atmospheric and marine corrosion of PEO and composite coatings obtained on Al-cu-Mg aluminum alloy10.3390/ma13122739 ↗
52. Microstructure and corrosion model of MAO coating on nano grained AA2024 pretreated by ultrasonic cold forging technology10.1016/j.jallcom.2016.03.196 ↗
53. On AC-DC voltage superposition in the oxide formation and corrosion performance of PEO-treated Al 6061 alloy
54. Effect of Si network continuity on the localized corrosion of AlSi10Mg alloy fabricated by selective laser melting10.1016/j.corsci.2025.113336 ↗
55. Significance of plasma electrolytic oxidation treatment on corrosion and sliding Wear performances of selective laser melted AlSi10Mg alloy10.1016/j.matchar.2021.111479 ↗
56. Recent advances in energy efficient PEO processing of Aluminium alloys10.1016/S1003-6326(17)60166-3 ↗
57. Cathodic pulse breakdown of anodic films on Aluminium in alkaline silicate electrolyte—understanding the role of the cathodic half-cycle in AC plasma electrolytic oxidation10.1016/j.corsci.2011.10.007 ↗
58. Effect of cathodic Micro-discharges on oxide growth during plasma electrolytic oxidation (PEO)10.1016/j.surfcoat.2015.01.076 ↗
59. Coating growth behavior during the plasma electrolytic oxidation process10.1116/1.3429583 ↗
60. Micro-structures and growth mechanisms of plasma electrolytic oxidation coatings on Aluminium at different current densities10.1016/j.surfcoat.2017.04.064 ↗
61. Influence of electrolyte components on the microstructure and growth mechanism of plasma electrolytic oxidation coatings on 1060 aluminum alloy10.1016/j.surfcoat.2019.125214 ↗
62. Investigation of the growth processes of coatings formed by AC plasma electrolytic oxidation of aluminum10.1016/j.electacta.2009.06.088 ↗
63. Delay in micro-discharges appearance during PEO of Al: evidence of a mechanism of charge accumulation at the electrolyte/oxide interface10.1016/j.apsusc.2017.03.088 ↗
64. Corrosion of an additively manufactured Ti6Al4V alloy in saline and acidic media10.3390/ma17030712 ↗
65. On the PEO treatment of cold sprayed 7075 aluminum alloy and its effects on mechanical, corrosion and dry sliding Wear performances thereof10.1016/j.surfcoat.2019.125271 ↗
66. Effect of silicon content on the mechanical and corrosion behavior of additively manufactured aluminum–silicon alloys via selective laser melting
67. Grain refining mechanism in the Al/Al–Ti–B system10.1016/j.actamat.2014.10.055 ↗