Optimization of properties of magnetron-sputtered copper coatings on carbon fiber-reinforced polymer composites via Ti and Cr interlayers
Source abstract
Abstract
To address the issues of weak interfacial adhesion and insufficient corrosion resistance of copper (Cu) coatings deposited on carbon fiber-reinforced polymer (CFRP) composites via magnetron sputtering, this study adopted a three-step process consisting of "15-minute Ti/Cr interlayer deposition + 8-minute co-deposition + 60-minute Cu deposition" to systematically compare the regulatory mechanisms of Ti and Cr interlayers on the microstructure and macroscopic properties of Cu coatings. The results showed that: Ti ions formed a gradient diffusion layer with a depth exceeding 2 μm through high-energy bombardment, and strong Ti-C/Ti-O bonds were formed with CFRP, which enabled the Ti-Cu coating to achieve an optimal pull-off strength of 6.23 MPa (6 times higher than that of the pure Cu coating) and the best Cu crystallinity; the Cr interlayer formed a dense Cr2O3 passivation film, which increased the electrical conductivity and infrared reflectivity of the Cr-Cu coating by 8% and 5% respectively after a 7-day salt spray test; the pure Cu coating exhibited weak adhesion due to interfacial physical adsorption (with a pull-off strength of only 0.89 MPa), leading to significant performance degradation after the salt spray test. In conclusion, the Ti interlayer is suitable for scenarios requiring high bonding strength, while the Cr interlayer is more applicable for cases where corrosion resistance is a priority. This research can provide technical references for the selection of interlayer materials in the metallization process of CFRP.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrodeposition and Electroless Coatings · Metal and Thin Film Mechanics · Material Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Metallization of polypropylene substrates through surface functionalization and physical vapor deposition of chromium coatings10.1016/j.surfcoat.2024.130880 ↗
2. Copper metallization of carbon fiber-reinforced epoxy polymer composites by surface activation and electrodeposition10.1016/j.surfcoat.2024.131016 ↗
3. Metallization technology of carbon fiber reinforced plastic surfaces through magnetron sputtering of Cu films10.1002/sia.7407 ↗
4. Residual stress depth profiling based on a triaxial stress model: the principal stress gradients in magnetron-sputtered molybdenum films10.1107/S160057672401080X ↗
5. Antiferromagnetic Cr-Mn alloys: Crystal structure, magnetic anisotropy, and exchange bias in magnetron-sputtered polycrystalline thin films10.1016/j.jmmm.2024.171958 ↗
6. Exploring the role of film thickness and oxygen vacancies on the H2S gas-sensing performance of RF magnetron-sputtered NiO thin films10.1007/s10853-024-10204-7 ↗
7. Wear study of a magnetron-sputtered TiC/a-C nanocomposite coating under media-lubricated oscillating sliding conditions10.3390/coatings12040446 ↗
8. Conversion of magnetron-sputtered sacrificial intermediate layer into a stable FeCo-LDH catalyst for oxygen evolution reaction10.1007/s12274-023-6385-4 ↗
9. Electron beam welding of dissimilar Ti6Al4V and Al6082-T6 alloys using magnetron-sputtered Cu interlayers10.3390/cryst15040373 ↗
10. Plasma treatment on the activation effect of the inner wall of CFRP cylindrical parts
11. Effect of pulsed electric field on the nanocrystalline growth of magnetron-sputtered TiAlN hard coatings10.1016/j.ceramint.2023.10.177 ↗
12. Ohmic losses on magnetron-sputtered PVD thin-film TCO electrodes of the electrochromic modules during their tinting10.1134/S106377882209023X ↗
13. Recent developments in magnetron-sputtered silicon nitride coatings of improved mechanical and tribological properties for extreme situations10.1007/s10853-023-08575-4 ↗
14. Comparison of magnetron-sputtered and cathodic Arc-deposited Ti and Cr thin films on stainless steel for bipolar plates10.3390/ma17122864 ↗
15. Angular distributions during magnetron sputtering of polycrystalline Mg, Al, Si, Ti, Cr, Cu, Zn, Ge, Zr, Nb, Mo, Ag, In, Sn, W, Pt, Au, and Bi targets10.1134/S0020441220040314 ↗
16. Spatially resolved optical emission analysis of spokes in HiPIMS utilising Al, Cr, Cu, Ti, and W targets10.1088/1361-6595/ad546b ↗
17. Tribological properties characterization of Ti/Cu/N thin films prepared by DC magnetron sputtering on titanium alloy
18. Antimicrobial nano-Ag/Cu composite coatings on pure Ti implants by magnetron sputtering following pretreatment for dental applications10.1002/adem.202402437 ↗
19. Comparative corrosion resistance properties between (Cu, Ce)-DLC and Ti co-doped (Cu, Ce)/Ti-DLC films prepared via magnetron sputtering method
20. Investigations of elemental composition and structure evolution in (Ti,Cu)-oxide gradient thin films prepared using (multi)magnetron co-sputtering
21. Microstructure and corrosion behavior of Ti nanoparticles reinforced Ni–Ti composite coatings by electrodeposition10.1016/j.matdes.2015.06.144 ↗
22. Structure and stress of Cu films prepared by high power pulsed magnetron sputtering
23. Optimization of photoelectric properties and temporal stability of AZO/Ti/Cu/AZO films by insertion of Ti layer for low emissivity applications10.1016/j.mseb.2023.116471 ↗
24. Tribo-mechanical performance and antibacterial activity in (Cu, Zr)-alloyed Ti(Al)N coatings synthesized by reactive magnetron sputtering10.1007/s10853-022-07804-6 ↗
25. Modes development of PLGA scaffolds modification by magnetron co-sputtering of Cu and Ti targets10.1088/1742-6596/1799/1/012001 ↗
26. Electron-beam welding of titanium and Ti6Al4V using magnetron-sputtered Nb, V, and Cu fillers10.3390/met14040417 ↗
27. The effect of CFRP surface treatment on the splat morphology and coating adhesion strength10.1007/s11666-013-0003-z ↗
28. Reverse engineering analysis of optical properties of (Ti,Cu)Ox gradient thin film coating10.3390/coatings13061012 ↗
29. Deposition and characterization for high-quality Ti–Ni–Cu thin films with higher Cu content10.1007/s12598-020-01489-z ↗
30. Effects of Cr doping in the structural and optoelectronic properties of Cu2ZnSnS4 (CZTS) thin film by magnetron co-sputtering10.1016/j.matlet.2018.03.056 ↗
31. Ti–Cu coatings deposited by a combination of HiPIMS and DC magnetron sputtering: the role of vacuum annealing on Cu diffusion, microstructure, and corrosion resistance10.3390/coatings10111064 ↗
32. Tunable room-temperature ferromagnetism in RF magnetron sputtered Al2Cr2Cu2O8 thin film10.1016/j.ceramint.2023.11.212 ↗
33. Influence of Cr ion bombardment on the growth of Cu coatings deposited by magnetron sputtering on ABS substrates10.3390/polym15010080 ↗
34. Microstructure of Cu75Cr25 alloys under different conditions10.4028/www.scientific.net/AMR.230-232.247 ↗
35. FIB-DIC ring-core measurement of the residual stress on HiPIMS W/Cu and Cr/Cu multilayer thin films10.1016/j.surfcoat.2024.130768 ↗
36. Impact of atmospheric pressure plasma treatment on surface metallization of CFRP composites10.1016/j.surfcoat.2021.127046 ↗
37. Effect of Cr interlayers on texture and magnetic properties of FeSi films with micrometer thickness
38. Constructing MIL-101(Cr) membranes on carbon nanotube films as ion-selective interlayers for lithium-sulfur batteries10.1088/1361-6528/ac5443 ↗
39. Solidification behavior of undercooled Cu98Cr2 alloys10.4028/www.scientific.net/MSF.694.760 ↗
40. Effect of Cr content on microstructure and properties of aged Cu−Cr−P alloys10.1016/S1003-6326(20)65490-5 ↗
41. Low-temperature bonding between F82H and Cr assisted by metastable Cr interlayers applied by pulsed laser deposition