journal article·2026-08Open access

Oxygen-plasma screening of ALD Al₂O₃ barriers on 3D-printed PLA for low-earth-orbit atomic-oxygen durability

Thaís Macedo Vieira, Marcelo Pego Gomes, Nierlly Karinni Galvão, Filipe Caldatto Dalan, Argemiro Soares da Silva Sobrinho, Homero Santiago Maciel, Rodrigo Sávio Pessoa

Abstract

Additively manufactured polylactic acid (PLA) is a lightweight, low-cost material for spacecraft hardware but undergoes rapid oxidative erosion in the atomic oxygen (AO) environment of low-Earth orbit (LEO). This study evaluates the AO resistance of PLA coated with Al₂O₃ films deposited by low-temperature thermal atomic layer deposition (ALD) using 100–1000 ALD cycles. Samples were exposed to low-pressure oxygen plasma in a capacitively coupled RF reactor under two exposure regimes: (i) a radical-dominated plasma bulk rich in atomic oxygen (O) radicals (with background O₂), and (ii) an ion-assisted cathode-sheath region where positive oxygen ions enhance material removal, used here as an accelerated oxidative-erosion proxy for AO-driven degradation. Atomic oxygen (O) generation in the plasma was monitored by optical emission actinometry, and FTIR, SEM, EDS mapping, spectroscopic ellipsometry on co-deposited Si reference coupons, and gravimetric analysis assessed chemical, morphological, and mass changes. In the plasma bulk, even the 100-cycle coating suppressed mass loss below the detection limit. In the cathode sheath, performance was orientation-dependent: in the face-up configuration (coated face toward the plasma), a 100-cycle coating reduced the etch rate by a factor of 82; in the face-down configuration, the reduction was by a factor of 3.90 relative to uncoated PLA, consistent with lateral ingress through edges and/or localized coating defects. Increasing the ALD cycle count improved face-down protection, and at 1000 cycles no measurable mass variation was detected for either orientation, indicating erosion suppression below the detection limit under cathode sheath exposure. Elemental mapping showed that incomplete coverage of recessed print features was a key cause of reduced protection at low cycle counts, which was mitigated by increased ALD cycle count and geometry-aware fixturing. Applying 250 ALD cycles to both sides of a flat PLA panel increases the mass by 37.5 mg per 100 cm 2 , while providing effective protection against both oxygen-radical ingress and ion-assisted erosion.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Silicone and Siloxane Chemistry · Plasma Diagnostics and Applications · Copper Interconnects and Reliability

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Biodegradable polylactic acid and its composites: characteristics, processing, and sustainable applications in sports10.3390/polym15143096 ↗
2. Exploring the use of biodegradable polymer materials in sustainable 3D printing10.59429/ace.v7i2.3870 ↗
3. Comprehensive exploration of natural degradation of poly(lactic acid) blends in various degradation media: a review10.1016/j.ijbiomac.2021.07.196 ↗
4. Differentiation between hydrolytic and thermo-oxidative degradation of poly(lactic acid) and poly(lactic acid)/starch composites in warm and humid environments10.3390/ma17153683 ↗
5. Dynamically balanced pointing system for CubeSats: study and 3D printing manufacturing10.3390/robotics10040121 ↗
6. Additive manufacturing of large structures using free-flying satellites10.3389/frspt.2022.879542 ↗
7. In vacuum performance of a 3D printed ion deflector10.1016/j.vacuum.2019.109061 ↗
8. Coatings made by atomic layer deposition for the protection of materials from atomic oxygen in space10.1088/1757-899X/1287/1/012014 ↗
9. Protection of polymer from atomic-oxygen erosion using Al₂O₃ atomic layer deposition coatings10.1016/j.tsf.2007.07.150 ↗
10. The improvement of DLC film lifetime using silver nanoparticles for use on space devices10.1016/j.diamond.2008.03.007 ↗
11. Synergistic effects of atomic oxygen and thermal cycling in low earth orbit on polymer-matrixed space material10.1016/j.heliyon.2023.e17431 ↗
12. Banks · 2012
13. Banks · 2009
14. Plasma-assisted nanofabrication: the potential and challenges in atomic layer deposition and etching10.3390/nano12193497 ↗
15. Atomic layer deposition of TiO₂ and Al₂O₃ thin films for the electrochemical study of corrosion protection in aluminum alloy cans used in beverage10.1088/2053-1591/aba557 ↗
16. Chemically stable atomic layer deposited Al₂O₃ films for processability10.1021/acsomega.7b00443 ↗
17. Growth and atomic oxygen erosion resistance of Al₂O₃ doped TiO₂ thin film formed on polyimide by atomic layer deposition10.1039/D4RA06464J ↗
18. Enhanced water vapor barrier properties for biopolymer films by polyelectrolyte multilayer and atomic layer deposited Al₂O₃ double-coating10.1016/j.apsusc.2011.06.031 ↗
19. Effect of heat-treatment on the performance of gas barrier layers applied by atomic layer deposition onto polymer-coated paperboard10.1002/app.34313 ↗
20. Functionalization of PLA films with ALD Al₂O₃ coatings for safe food packaging10.1177/87560879251376253 ↗
21. Towards space-grade 3D-printed, ALD-coated small satellite propulsion components for fluidics
22. Exploring TMA and H2O flow rate effects on Al2O3 thin film deposition by thermal ALD: insights from zero-dimensional modeling10.3390/coatings14050578 ↗
23. Novel energetic co-reactant for thermal oxide atomic layer deposition: the impact of plasma-activated water on Al2O3 film growth10.3390/nano13243110 ↗
24. Pyrolysis kinetic study of polylactic acid
25. Automation of a mass flow controller for application in time-multiplex SF₆+CH₄ plasma etching of silicon
26. Chemistry studies of SF6/CF4, SF6/O2 and CF4/O2 gas phase during hollow cathode reactive ion etching plasma10.1016/j.vacuum.2014.03.003 ↗
27. Low temperature atomic layer deposition of Al₂O₃ films10.1021/cm0304546 ↗
28. Comparison of precursor infiltration into polymer thin films via atomic layer deposition and sequential vapor infiltration using in-situ quartz crystal Microgravimetry10.1116/1.4882654 ↗
29. Comparison of the growth and thermal properties of nonwoven polymers after atomic layer deposition and vapor phase infiltration10.3390/coatings11091028 ↗
30. Mechanisms and reactions during atomic layer deposition on polymers10.1016/j.ccr.2013.07.001 ↗
31. Sequential vapor infiltration of metal oxides into sacrificial polyester fibers: shape replication and controlled porosity of microporous/mesoporous oxide materials10.1021/cm200694w ↗
32. A route to nanoscopic materials via sequential infiltration synthesis on block copolymer templates10.1021/nn2003234 ↗
33. Vapor phase infiltration (VPI) for transforming polymers into organic–inorganic hybrid materials: a critical review of current progress and future challenges10.1039/C7MH00196G ↗
34. Atomic-layer-deposited aluminum oxide thin films probed with X-ray scattering and compared to molecular dynamics and density functional theory models10.1021/acsomega.2c04402 ↗
35. On the differences in trimethylaluminum infiltration into PMMA and PLA polymers for sequential infiltration synthesis: insights from experiments and first-principles simulations10.1021/acsapm.5c02680 ↗
36. Vapor phase infiltration: from a bioinspired process to technologic application, a prospective review10.1557/mrc.2018.126 ↗
37. Biocompatibility assessment of Poly(lactic acid) films after sterilization with Ethylene Oxide in histological study In Vivo with Wistar rats and cellular adhesion of fibroblasts In Vitro10.1155/2017/7158650 ↗
38. Explication of mechanism governing atmospheric degradation of 3D printed poly(lactic acid) (PLA) with different in fill pattern and varying in fill density10.1039/D2RA07061H ↗
39. Study on 3D printability of PLA/PBAT/PHBV biodegradable blends for packaging applications10.1016/j.polymertesting.2025.108748 ↗
40. Effect of various oxidants on reaction mechanisms, self-limiting natures and structural characteristics of Al₂O₃ films grown by atomic layer deposition10.1002/admi.201870070 ↗
41. Mechanical strengths and thermal properties of titania-doped alumina aerogels and the application as high-temperature thermal insulator10.1007/s10971-019-05057-5 ↗
42. High specific surface area γ-Al2O3 nanoparticles synthesized by facile and low-cost co-precipitation method10.1038/s41598-023-33266-0 ↗
43. Experimental investigation on the spatial distribution of floating potential at the wafer-level in inductively coupled oxygen plasma10.1063/1.5085703 ↗
44. A volume averaged global model study of the influence of the electron energy distribution and the wall material on an oxygen discharge10.1088/0022-3727/48/49/495203 ↗
45. Ion energy and angular distributions in low pressure capacitive oxygen RF discharges driven by tailored voltage waveforms10.1088/1361-6595/aae5c3 ↗
46. Ion and radical characteristics (mass/energy distribution) of a capacitively coupled plasma source using plasma process gases (CxFy)10.3390/coatings11080993 ↗
47. Ion energy distributions in RF sheaths; review, analysis and simulation10.1088/0963-0252/8/3/202 ↗
48. NASA · 2014
49. De Groh · 2009
50. NIST-JANAF thermochemical tables
51. Fabrication of high-performance ALD-Al₂O₃/SiO₂ nanolaminate coating for atomic oxygen erosion resistance on polyimide10.1016/j.surfcoat.2025.131960 ↗
52. Protecting polymers in space with atomic layer deposition coatings10.1021/am100217m ↗