journal article·2026-09

Ablation and insulation performance of Al2O3/PI coatings deposited by wide-velocity range high-energy plasma spraying

J.Y. Zhu, K.Y. Xu, Y.M. Tu, Y. Wang, Y. Bai, Y.H. Du

Publisher page

Abstract

Transient thermo-erosion induced by thermal plasma and molten aluminum armature droplets during electromagnetic rail launcher (EMRL) operation is a major cause of performance degradation in insulating supports. Surface coatings provide an effective route for improving their service reliability. In this work, Al2O3/PI composite coatings were deposited on glass-fiber-reinforced epoxy resin (GFRP) substrates by wide-velocity range high-energy plasma spraying (WPS). By varying the ratio of thermoplastic polyimide (TPI) to thermosetting polyimide (TSPI) (10:0, 7:3, 5:5, and 3:7), the effects of dual-phase PI composition on coating microstructure, mechanical properties, ablation resistance, and insulation performance were systematically investigated. The results showed that PI73 exhibited the lowest mass ablation rate after 150 plasma ablation cycles, while maintaining a high flexural strength of 228.61 MPa. After molten aluminum erosion, the Al2O3/PI composite coatings still maintained markedly higher volume resistivity than the substrate. This behavior is attributed to the synergistic protection of the Al2O3/PI coating, where the ceramic phase promotes heat dissipation and residual-layer stability, while the polymer phase contributes to penetration resistance and structural integrity. The present study demonstrates that an appropriate thermoplastic/thermosetting dual-phase PI design is effective for simultaneously improving the ablation resistance and insulation performance of Al2O3/PI composite coatings, and provides a new design route for resin-based insulating materials operating under extreme thermo-erosive conditions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electromagnetic Launch and Propulsion Technology · Tribology and Wear Analysis · Gas Dynamics and Kinetic Theory

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. Thinking and study of electromagnetic launch technology10.1109/TPS.2017.2705979 ↗
2. An internal ballistic model of electromagnetic railgun based on PFN coupled with multi-physical field and experimental validation10.1016/j.dt.2023.08.015 ↗
3. Research progress on advanced rail materials for electromagnetic railgun technology10.1016/j.dt.2020.03.014 ↗
4. Prospects of use of electromagnetic railgun as plasma thruster for spacecrafts10.1016/j.actaastro.2017.12.035 ↗
5. Electromagnetic gun technology and its development
6. Research on armature’s wearing and dynamic interior ballistic of a railgun10.1109/TPS.2017.2701414 ↗
7. Additive manufacturing of natural fiber reinforced polymer composites: processing and prospects10.1016/j.compositesb.2019.106956 ↗
8. Recent progresses of fabrication and characterization of fibers-reinforced composites: a review10.1016/j.coco.2019.05.004 ↗
9. Fiber-reinforced polymer composites: manufacturing, properties, and applications10.3390/polym11101667 ↗
10. Research on insulation problems under multishot experiments in electromagnetic rail launcher10.1109/TPS.2017.2705219 ↗
11. Science and technology of polymeric ablative materials for thermal protection systems and propulsion devices: a review10.1016/j.pmatsci.2016.08.003 ↗
12. A review of thermally sprayed polymer coatings10.1007/s11666-022-01404-1 ↗
13. Metallization of polymers and composites: state-of-the-art approaches10.1016/j.matdes.2022.110958 ↗
14. Thermal spray applications in electronics and sensors: past, present, and future10.1007/s11666-010-9475-2 ↗
15. Fabrication of thermal barrier coatings onto polyimide matrix composites via air plasma spray process10.1016/j.surfcoat.2012.07.042 ↗
16. A review of thermal spray metallization of polymer-based structures10.1007/s11666-016-0415-7 ↗
17. Multi-layered thermal barrier coatings on BMI polyimide matrix composite10.1016/j.surfcoat.2018.01.007 ↗
18. Effect of bond coats on thermal shock resistance of thermal barrier coatings deposited onto polymer matrix composites via air plasma spray process10.1007/s11666-013-9942-7 ↗
19. Erosion resistance improvement of polymer matrix composites by detonation-sprayed multilayered coatings10.1007/s11666-020-01120-8 ↗
20. Study on process and performance of thermal protective coating on polyimide resin matrix composite10.1016/j.ceramint.2020.02.043 ↗
21. Surface metallization and ceramic deposition on thermoplastic-polymer and thermosetting-polymer composite via atmospheric plasma spraying10.1007/s12540-020-00864-w ↗
22. Adhesion strength improvement of thermally sprayed metallic coating on carbon-fiber-reinforced polymer composite
23. High velocity flame spraying of highly-filled ceramic — polymer filaments (F-HVOF)10.1016/j.surfcoat.2023.129324 ↗
24. The effect of laser textured resin surface on the adhesion of supersonic plasma sprayed Al2O3/PF composite coating10.1016/j.surfcoat.2024.130990 ↗
25. Research on the ablation resistance of Al2O3/PF composite coatings deposited by supersonic plasma spraying on resin matrix surfaces10.1016/j.surfcoat.2024.131140 ↗
26. Ablation resistance and erosion wear properties of supersonic plasma sprayed Al2O3-PF composite coatings prepared on resin surface10.1016/j.surfcoat.2025.131900 ↗
27. Development mechanism and performance of Al2O3-PF composite coating on epoxy resin matrix composite surface by supersonic plasma spraying10.1016/j.surfcoat.2022.128762 ↗
28. Damage research of supersonic plasma sprayed Al2O3/PF composite coatings on resin matrix surfaces under thermally coupled operating conditions10.1016/j.surfcoat.2025.131905 ↗
29. Tribological properties and solid particle erosion wear behavior of Al2O3-13 wt%TiO2/Al2O3-PF composite coatings prepared on resin matrix by supersonic plasma spraying10.1016/j.ceramint.2024.05.294 ↗
30. Phase composition, microstructure, mechanical properties, and wear performance of nanostructured Al2O3 and Al2O3-Y2O3 coatings deposited by plasma spraying10.1016/j.apsusc.2022.152754 ↗
31. Comprehensive study on corrosion protection properties of Al2O3, Cr2O3 and Al2O3–Cr2O3 ceramic coatings deposited by plasma spraying on carbon steel10.1016/j.ceramint.2021.09.237 ↗
32. Comparison of the microstructural characteristics and electrical properties of plasma sprayed Al2O3 and Al2O3–Ca2SiO4 coatings immersed in deionized water10.1016/j.surfcoat.2021.127530 ↗
33. Advanced polyimide materials: syntheses, physical properties and applications10.1016/j.progpolymsci.2012.02.005 ↗
34. High-temperature-resistant and colorless polyimide: preparations, properties, and applications10.1016/j.solener.2019.11.048 ↗
35. High temperature polyimide nanocomposites containing two-dimensional nanofillers for improved thermal stability and capacitive energy storage performance10.1007/s12274-024-6765-4 ↗
36. Facile fabrication of polyimide-alumina composite coatings by liquid flame spray10.3390/coatings10090857 ↗
37. Impact of nano-Al2O3 coating on the dielectric properties and high-frequency surface electrical strength of the polyimide films10.1016/j.apsusc.2023.157666 ↗
38. Performance of high-temperature thermosetting polyimide composites modified with thermoplastic polyimide10.1016/j.polymertesting.2020.106746 ↗
39. ASTM C633-13 · 2021
40. Aluminum foam sandwich with density-graded open-cell core: compressive and flexural response10.1016/j.msea.2018.06.048 ↗
41. ASTM D257-14 · 2021 · 2021
42. Spreading behavior and morphology of ethylene methacrylic acid (EMAA) deposits via the flame spray process10.3390/coatings2020076 ↗
43. Splat taxonomy of polymeric thermal spray coating10.1016/j.surfcoat.2011.05.002 ↗
44. Effect of low-temperature imidization on properties and aggregation structures of polyimide films with different rigidity10.1007/s10118-024-3137-1 ↗
45. Cure kinetics and thermal decomposition behavior of novel phenylacetylene-capped polyimide resins10.3390/polym16081149 ↗
46. Two-dimensional correlation analysis of polyimide films using attenuated total reflection-based dynamic compression modulation step-scan Fourier transform infrared spectroscopy10.1366/000370207781540015 ↗
47. Tuning the heat resistance properties of polyimides by intermolecular interaction strengthening for flexible substrate application10.1016/j.polymer.2019.04.032 ↗
48. Thermal analysis of high-energy railgun tests10.1109/TPS.2011.2174375 ↗
49. Analysis of GFRP insulator characteristics under multiphysical fields in electromagnetic rail launchers10.1016/j.compstruct.2019.110900 ↗
50. Armature ejecta and its effects on insulator degradation in solid-armature launchers10.1109/TPS.2022.3143143 ↗
51. Experimental study of railgun aluminum armature electrical contact ablation10.3233/JAE-141935 ↗
52. Wetting and spreading behaviour of molten CMAS towards thermal barrier coatings and its influencing factors10.1016/j.rinp.2021.104365 ↗
53. DC conduction and breakdown behavior of thermally sprayed ceramic coatings10.1109/TDEI.2016.006156 ↗
54. Effect of temperature and humidity on dielectric properties of thermally sprayed alumina coatings10.1109/TDEI.2018.006892 ↗