journal article·2026-09

Densification outweighs amorphous retention: Corrosion mechanisms of wide-velocity-range plasma sprayed Fe-based coatings

W. Liang, F.L. Yu, J.H. Zu, B. Qian, J.L. Yang, Y. Wang, Z. Gu, R.J. Wang, H. Zhan, Y. Bai

Publisher page

Abstract

Iron-based amorphous coatings (Fe-AMCs) are promising candidates for corrosion protection. However, it remains challenging to achieve a dense microstructure with few defects while maintaining a high amorphous phase content. In this study, Fe-Cr-Si-Mo-Mn-Ni-W amorphous coatings were deposited onto 316L stainless steel using the wide-velocity-range plasma spraying (WPS) method, with five parameter combinations varying in argon flow rate and spray current. The phase composition, amorphous phase content, microstructure, porosity, bond strength, microhardness, and electrochemical corrosion behavior in a 3.5 wt.% NaCl solution were systematically investigated. The results showed that the feedstock powders were nearly fully amorphous (98%), whereas the as-sprayed coatings retained 90%~96% of the amorphous phase, indicating that partial crystallization occurred during deposition. Within this high amorphous retention range, the coating with the highest amorphous phase content did not exhibit the highest corrosion resistance. In contrast, the coating with the lowest porosity (1.4%) exhibited the highest charge transfer resistance (1863 Ω·cm2 ) and the lowest corrosion current density (21.25 μA·cm⁻2 ). These results revealed that, within the examined WPS process window where the amorphous phase content of the coatings ranged from 90% to 96%, differences in corrosion resistance were governed primarily by coating density rather than by relatively minor variations in the amorphous phase content itself.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallic Glasses and Amorphous Alloys · High-Temperature Coating Behaviors · Nanoporous metals and alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. Influence of Ni, Al, W doping on microstructure, corrosion and wear resistance of HVOF spraying Fe-based amorphous alloy coatings10.1016/j.jmrt.2025.01.066 ↗
2. Stabilization of metallic supercooled liquid and bulk amorphous alloys10.1016/S1359-6454(99)00300-6 ↗
3. Non-crystalline structure in solidified gold–silicon alloys10.1038/187869b0 ↗
4. Investigation of corrosion and wear performance of Fe50(Cr-Mo)25(B0.5C0.4Si0.1)25 amorphous alloy coatings: flakes size perspective
5. Optimization of mechanical and corrosion properties of plasma sprayed low-chromium containing Fe-based amorphous/nanocrystalline composite coating10.1016/j.surfcoat.2019.05.010 ↗
6. Mechanical properties and corrosion resistance analysis of Fe-based amorphous −2% CNTs coatings with low crack prepared by laser cladding10.1016/j.diamond.2025.112288 ↗
7. Effect of heat treatment on erosion–corrosion of Fe-based amorphous alloy coating under slurry impingement10.1016/j.jallcom.2019.153132 ↗
8. Pitting initiation in Fe-based amorphous coatings10.1016/j.actamat.2012.04.005 ↗
9. High temperature wear and corrosion behavior of detonation sprayed Fe-based amorphous coatings10.1038/s41598-024-80308-2 ↗
10. Microstructure and Tribological behavior of supersonic atmospheric plasma-sprayed Mo-/Fe-based amorphous coating10.1007/s11666-022-01460-7 ↗
11. Corrosion and wear resistance of Fe-based amorphous coatings
12. A study on the corrosion inhibition of Fe-based amorphous/Nanocrystalline coating synthesized by high-velocity oxy-fuel spraying in an extreme environment10.1007/s11666-019-00907-8 ↗
13. The role of alloying elements in improving the corrosion resistance of amorphous iron base alloys10.1016/S0010-938X(79)80109-2 ↗
14. Effects of oxygen fuel rate on microstructure and Wear properties of detonation sprayed Iron-based amorphous coatings10.2320/matertrans.M2018273 ↗
15. The wear properties and mechanism of detonation sprayed iron-based amorphous coating10.1016/j.surfcoat.2019.03.028 ↗
16. Residual stress model in laser direct deposition based on energy equation10.3390/coatings15020217 ↗
17. Chlorine-induced high-temperature corrosion and erosion-corrosion of HVAF and HVOF-sprayed amorphous Fe-based coatings10.1016/j.surfcoat.2019.01.080 ↗
18. Microstructure and properties of AlCrFeNiMoNb high-entropy alloys coating on ZM5 magnesium alloy prepared by high-velocity air fuel (HVAF) spray10.1016/j.jmrt.2023.09.125 ↗
19. Wettability and corrosion performance of arc-sprayed Fe-based amorphous coatings10.1016/j.surfcoat.2022.128129 ↗
20. Microstructure, mechanical and tribological properties of cold sprayed Fe-based metallic glass coatings
21. Environmentally assisted fracture behavior of Fe-based amorphous coatings in chloride-containing solutions10.1016/j.jallcom.2017.12.150 ↗
22. Process—structure—property relationship for plasma-sprayed iron-based amorphous/crystalline composite coatings10.1007/s12613-020-2171-4 ↗
23. Microstructure, mechanical and wear performance of Fe-based amorphous coatings fabricated by high velocity air-fuel spraying10.1007/s11666-022-01378-0 ↗
24. Fe-based amorphous/nanocrystalline composite coating by plasma spraying: effect of heat input on morphology, phase evolution and mechanical properties10.1016/j.jallcom.2018.09.024 ↗
25. Corrosion behavior of CoNiCrMoNbBSi high-entropy amorphous coating via experiment and simulation investigations10.1016/j.apsusc.2026.166303 ↗
26. Fabrication and characterization of supersonic plasma sprayed Fe-based amorphous metallic coatings10.1016/j.matdes.2016.08.003 ↗
27. Corrosion wear properties of Fe-based amorphous coatings sprayed by supersonic atmospheric plasma spraying10.1016/j.surfcoat.2024.131678 ↗
28. Influence of the size of spraying powders on the microstructure and corrosion resistance of Fe-based amorphous coating10.1016/j.electacta.2011.05.020 ↗
29. Effect of HVOF spraying process on particle behavior of Fe-based amorphous alloy coatings10.1007/s11666-022-01476-z ↗
30. Spraying of Fe-based amorphous coating with high corrosion resistance by HVAF10.1016/j.jmapro.2016.01.009 ↗
31. Microstructural evolution of carbides and its effect on tribological properties of SAPS or HVOF sprayed NiCr–Cr3C2 coatings10.1016/j.jallcom.2019.06.291 ↗
32. A study of high velocity oxy-fuel thermally sprayed tungsten carbide based coatings. Part 1: microstructures10.1016/S0921-5093(97)00759-4 ↗
33. Effect of feedstock particle sizes on wear resistance of plasma sprayed Fe-based amorphous coatings10.1016/j.surfcoat.2014.08.050 ↗
34. Identifying the optimal HVOF spray parameters to attain minimum porosity and maximum hardness in iron based amorphous metallic coatings10.1016/j.dt.2017.03.001 ↗
35. Effect of porosity defects on the long-term corrosion behaviour of Fe-based amorphous alloy coated mild steel10.1016/j.corsci.2016.04.021 ↗
36. Fe-based amorphous alloy coatings: a review10.1002/adem.202302184 ↗
37. Microstructures and corrosion resistance of Fe-based amorphous/nanocrystalline coating fabricated by laser cladding10.1016/j.jallcom.2017.08.251 ↗
38. Wear and corrosion resistant performance of thermal-sprayed Fe-based amorphous coatings: a review10.1016/j.surfcoat.2019.124896 ↗
39. Investigation of nano- and micro-scale structural evolution and resulting corrosion resistance in plasma sprayed Fe-based (Fe-Cr-B-C-P) amorphous coatings10.1016/j.surfcoat.2020.126058 ↗
40. Study of structure and corrosion resistance of Fe-based amorphous coatings prepared by HVAF and HVOF10.1016/j.corsci.2010.12.022 ↗
41. Effects of crystallization on the corrosion resistance of Fe-based amorphous coatings10.1016/j.corsci.2012.02.003 ↗
42. Investigation on pitting corrosion mechanism of the Fe-based amorphous alloy coating by three-dimensional X-ray imaging at micro-scale10.1016/j.jmrt.2023.09.026 ↗
43. Wear and corrosion resistant of NiFeSiBPNb amorphous alloy coatings sprayed by HVOF10.1016/j.intermet.2025.108823 ↗