journal article·2026-09Open access

Influence of α-Al2O3 texture on residual stress, cooling cracks and hardness in CVD α-Al2O3/Ti(C,N) coatings on cemented carbide

Larissa Juliana Sirtuli, Amol Thakare, Susanne Norgren, Jonas Östby, Siamak Shoja

Abstract

CVD α-Al2O3 coatings on cemented carbides are widely used in steel turning, where cutting tool performance is strongly dependent on the crystallographic texture of the α-Al2O3 layer. Residual stress, cooling-crack density, and hardness are key factors influencing coating integrity during machining. Although texture has been reported to affect these properties, trends remain inconsistent in the literature. In this work, three CVD α-Al2O3/Ti(C,N) coatings with identical architecture, substrate, and processing route, but distinct α-Al2O3 textures: i. c-plane (0001) , ii. r-plane (01-12) , and iii. a-plane (11-20) were investigated to isolate the role of texture under controlled conditions. The (0001) coating exhibited the highest tensile residual stress and the lowest crack density, while the (01-12) and (11-20) coatings showed lower stresses and denser crack network. This behaviour is consistent with a texture-dependent thermal expansion mismatch, complemented by orientation-dependent stress accommodation during cooling. The (01-12) and (11-20) textures, with a greater in-plane contribution of the c-axis, develop higher intrinsic thermal stress and thus promote more extensive crack formation for stress relaxation compared to texture. Nanohardness values were comparable across the three textures. The results demonstrate that α-Al2O3 texture has a clear influence on residual stress and cracking, but a limited effect on hardness. These findings provide a more consistent basis for interpreting texture–property relationships and suggest that the performance of (0001)-textured coatings in steel turning is primarily associated with reduced crack density and their response under directional loading, rather than with differences in hardness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Chemical vapor deposited TiCN/TiC multilayer coatings: on the interplay between coating architecture and mechanical properties10.1016/j.ijrmhm.2024.106890 ↗
2. Crystallographic orientation and surface morphology of chemical vapor deposited Al2O310.1149/1.2120043 ↗
3. Preparation of alumina coatings by chemical vapour deposition10.1016/0040-6090(86)90214-2 ↗
4. Factors influencing the κ-Al2O3 → α-Al2O3 phase transformation during CVD growth10.1016/0257-8972(93)90022-G ↗
5. Characterisation of the κ-Al2O3→α-Al2O3 transformation in different single layer coatings of CVD κ-Al2O310.1016/0257-8972(95)02580-4 ↗
6. Microstructural investigation of as-deposited and heat-treated CVD Al2O310.1016/S0257-8972(97)00479-9 ↗
7. Phase transformation in chemically vapour-deposited :-alumina10.1016/0040-6090(92)90761-Y ↗
8. Microstructural study of the κ-Al2O3 → α-Al2O3 transformation in CVD κ-Al2O3
9. Microstructural investigation of the κ-Al2O3 → α-Al2O3 transformation in multilayer coatings of chemically vapour deposited κ-Al2O310.1016/0040-6090(94)90340-9 ↗
10. Characterization of α-Al2O3, κ-Al2O3, and α-κ multioxide coatings on cemented carbides10.1016/S0040-6090(05)80063-X ↗
11. The influence of the nucleation surface on the growth of CVD α-Al2O3 and κ-Al2O310.1016/0257-8972(95)02584-7 ↗
12. Deposition, microstructure and properties of texture-controlled CVD α-Al2O3 coatings10.1016/j.ijrmhm.2005.05.004 ↗
13. Enhanced performance of α-Al2O3 coatings by control of crystal orientation10.1016/j.surfcoat.2008.03.021 ↗
14. Influence of process conditions on the growth and texture of CVD alpha-alumina10.3390/coatings10020158 ↗
15. Seco Tools · 2015
16. Sandvik Coromant, Sandvik Coromant - Our history - Our Innovations, (n.d.). https://www.sandvik.coromant.com/sv-se/about-us/our-history/our-innovations (accessed July 6, 2026).
17. Shoja · 2022
18. Calculated and experimental Schmid factors for chip flow deformation of textured CVD α-alumina coatings10.1016/j.surfcoat.2021.126991 ↗
19. Enhanced steel machining performance using texture-controlled CVD alpha-alumina coatings: Fundamental degradation mechanisms10.1016/j.ijmachtools.2024.104137 ↗
20. Wear and thermal behaviour of CVD α-Al2O3 and MTCVD Ti(C,N) coatings during machining10.1016/j.cirp.2009.03.059 ↗
21. Microstructure and wear mechanisms of texture-controlled CVD α-Al2O3 coatings10.1016/j.wear.2017.01.071 ↗
22. Wear mechanism of thermally transformed CVD Al2O3 layer10.1016/j.ijrmhm.2005.11.007 ↗
23. Thermal crack formation in TiCN/α-Al2O3 bilayer coatings grown by thermal CVD on WC-Co substrates with varied Co content10.1016/j.surfcoat.2020.125687 ↗
24. Residual-stress predictions in polycrystalline alumina10.1111/j.1151-2916.2001.tb01119.x ↗
25. The influence of residual thermal stresses on the mechanical properties of multilayer α-Al2O3/TiCxN1 − x coatings on WC/Co cutting tools10.1016/j.surfcoat.2012.07.088 ↗
26. On the relationship between texture characteristics and residual stress levels: An X-ray diffraction study on α-Al2O3 hard coatings10.1016/j.tsf.2023.139893 ↗
27. Chien
28. Abrasive wear of texture-controlled CVD α-Al2O3 coatings10.1016/j.surfcoat.2007.06.063 ↗
29. Giovannini · 2018
30. Microtexture and hardness of CVD deposited α-Al2O3 and TiCxN1−x coatings10.1016/j.ijrmhm.2008.09.010 ↗
31. Nanoindentation hardness, texture and microstructure of α-Al2O3 and κ-Al2O3 coatings10.1016/j.tsf.2007.10.078 ↗
32. Mechanical properties of single and polycrystalline α-Al2O3 coatings grown by chemical vapor deposition10.1016/j.surfcoat.2021.126959 ↗
33. Microstructure investigation of textured CVD alumina coatings10.1016/j.ijrmhm.2019.105125 ↗
34. Noyan · 1987
35. Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
36. Mechanical characterization of bilayer TiCN- αAl₂O₃ coating on WC-Co substrate using nanoindentation, SEM, EBSD and x-ray diffraction10.1016/j.ijrmhm.2026.107807 ↗
37. Freund · 2004
38. Study of initial notch wear during turning of stainless steel with CVD Al2O3/Ti(C,N) coated cemented carbide tools10.1016/j.ijrmhm.2025.107116 ↗
39. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
40. Atomistic insights into nanoindentation-induced deformation of α-Al2O3 single crystals10.1016/j.vacuum.2023.112733 ↗
41. Slip and twinning dislocations in sapphire (α-Al2O3)10.1080/01418619808241934 ↗
42. Hall–Petch effect in binary and ternary alumina/zirconia/spinel composites10.1016/j.jmrt.2021.01.058 ↗