Comparison of tribological properties of metal–metal and metal–cermet couples under lubricated and dry conditions
Source abstract
Abstract
The focus of this paper is on the determination of friction, wear, and film forming characteristics in conventional metal–metal couples and in cermet–metal couples. The tribological behaviour of a WC–Co based cermet applied by the HVOF process to a carbon steel substrate has been investigated in contact with cast iron, and this behaviour has been compared with carbon steel–cast iron couples. A mineral oil, a mineral oil containing zinc dialkyldithiophosphate (ZDDP), and a fully formulated lubricant were used for lubrication. The results show that the behaviour of the lubricant, in terms of its film forming and friction behaviour, is critically dependent on the load. The oil containing ZDDP shows a very significant increase in its ability to form a boundary film as the load increases.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
The Department of Mechanical and Chemical EngineeringHeriot-Watt University, Edinburgh, EH14 4AS, UK
References (26)
Show source-provided references
1. 10.1016/0043-1648(93)90394-210.1016/0043-1648(93)90394-2 ↗
2. PARKER D. A., ETTLES C. M. M., and RICHMOND J. W.: Proc. Conf. C70, 51–65; 1985, London, IMechE.
3. MOORE S. L. · 1987
4. GAUTAM M. · 1998
5. OGAWA Y. · 1987
6. WADE W. R., HAVSTAD P. H., RAO V. D., AIMONE M. G., and JONES C. M.: SAE technical paper 870651, SAE, Warrendale, PA, 1987. NAYLOR M. G. S., and FEAR M. P.: Proc. Workshop on �Coatings for advanced heat engines’, Castine, MN, 1990, 93–103.
7. NAYLOR M. G. S.: in �Wear-resistant ceramic coatings’, 273–281; Warrendale, PA, SAE.
8. lester T. · Surf. Active · 1998
9. barbezat G. · Wear · 1993 · 162
10. 10.1016/0043-1648(93)90274-P10.1016/0043-1648(93)90274-P ↗
11. 10.1016/0301-679X(90)90003-810.1016/0301-679X(90)90003-8 ↗
12. JAHANMIR S. · J. Tribol. (Trans. ASME) · 1986 · 46 · 577
13. KVERNES I. · 1986
14. DELAET M., and CODDET C.: in �Advanced design and operations’, Vol. 2, 57–66; 1996, New York, NY, ASME International.
15. HARRISON K., and NICOLL A. R.: in �Advances in surface engineering’, 131–146; 1997, Cambridge, Royal Society of Chemistry.
16. klaus E. E. · Lubr. Eng. · 47
17. 10.1002/tt.302001040310.1002/tt.3020010403 ↗
18. 10.1016/0301-679X(95)00024-X10.1016/0301-679X(95)00024-X ↗
19. 10.1016/0043-1648(96)06942-610.1016/0043-1648(96)06942-6 ↗
20. 10.1002/ls.301006020210.1002/ls.3010060202 ↗
21. 10.1023/A:101861481113110.1023/A:1018614811131 ↗
22. 10.1016/0043-1648(87)90020-210.1016/0043-1648(87)90020-2 ↗
23. 10.1016/0301-679X(95)00025-Y10.1016/0301-679X(95)00025-Y ↗
24. 10.1080/1040200940898329710.1080/10402009408983297 ↗
25. 10.1016/0272-8842(95)00088-710.1016/0272-8842(95)00088-7 ↗
26. 10.1016/0043-1648(94)90195-310.1016/0043-1648(94)90195-3 ↗