journal article·1997-01

Evolution of microstructure in BaTiO3 thin films recrystallised by laser

M. Okutomi, T. Tsukamoto, S. Niki, N. B. Dahotre

Surface Engineering· Volume 13· Issue 1
Publisher page

Abstract

Barium titanate ceramic thin films fabricated by the electrophoretic deposition technique were recrystallised using scanned CO2 laser irradiation. Conventionally the film is sintered at high temperature (1200°C) to increase adhesive forces between powdered ceramic film and substrate. During this process, however, many micropores and microcracks are produced owing to large shrinkage of fine aggregate grains in the film layer. In order to produce preferred orientation grainswithout these defects, the films were instantaneously melted by laser irradiation and recrystallised. The microstructure of the resulting thin film showed significant growth of platelike crystals and strip grain morphology on the surface. The recrystallised phase of BaTiO3 was tetragonal. Thus the laser scanning process appears to be suited to generating large grains with preferred orientation. In hysteresis D–E curve measurements, remanent polarisation of 48 mCm –2 and coercive field of 320 kVm–1 were the best dielectric and ferroelectric properties obtained in a film of 4 μm thickness.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Ferroelectric and Piezoelectric Materials · Electrophoretic Deposition in Materials Science · Electronic and Structural Properties of Oxides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (13)

Show source-provided references
1. NOMURA H., OKUTOMI M., KITAGAWA A., and ONISHI T.: Proc. Int. Conf. on Superconductors, Tsukuba, Japan, 1989, 11–17.
2. OKUTOMI M., KITAGAWA A., and NOMURA H.: in ‘Surface modification technologies IV’, (ed. Sudarshan T. S., Bhat D. G., and Jeandin M.), 145–161; 1991, Warrendale, PA, TMS.
3. 10.1007/978-4-431-68117-5_9110.1007/978-4-431-68117-5_91 ↗
4. 10.1080/1042691910893475610.1080/10426919108934756 ↗
5. 10.1143/JJAP.32.418210.1143/JJAP.32.4182 ↗
6. 10.1111/j.1151-2916.1955.tb14585.x10.1111/j.1151-2916.1955.tb14585.x ↗
7. 10.1111/j.1151-2916.1989.tb06309.x10.1111/j.1151-2916.1989.tb06309.x ↗
8. 10.1111/j.1151-2916.1956.tb15591.x10.1111/j.1151-2916.1956.tb15591.x ↗
9. 10.1111/j.1151-2916.1956.tb15592.x10.1111/j.1151-2916.1956.tb15592.x ↗
10. 10.1111/j.1151-2916.1957.tb12603.x10.1111/j.1151-2916.1957.tb12603.x ↗
11. 10.1016/0025-5408(68)90127-X10.1016/0025-5408(68)90127-X ↗
12. OKUTOMI M., MAKITA Y., and TAMAMAKI M.: in ‘Surface modification technologies VI’, (ed. Sudarshan T. S. et al.), 549–567; 1993, Warrendale, PA, TMS.
13. 10.1143/JPSJ.17.40410.1143/JPSJ.17.404 ↗