journal article·2013-08

High strength electron beam welded titanium–stainless steel joint with V/Cu based composite filler metals

Ting Wang, Binggang Zhang, Guoqing Chen, Jicai Feng

Vacuum· Volume 94
Publisher page

Abstract

Abstract Composite V/Cu based filler metals for electron beam welding of titanium–stainless steel joint were designed, based on the element metallurgical compatibility. Powder metallurgy method was used to manufacture the filler metal. To determine the feasibility of these filler metals, microstructures were analyzed by optical microscopy, scanning electron microscopy and X-ray diffraction. Mechanical properties of the joints were evaluated by tensile strength tests. The feasibility of the Cu/V filler metal was poor for the differences in physical properties between copper and vanadium, vanadium and titanium. A non-fusion defect was produced in the joint under low heat input, and cracking occurred in the joint under higher heat input due to the continuously distributed brittle TiCu, TiFe and τ 2 compounds. However, such defects were eliminated using a powder metallurgical V/Cu–V filler metal. A joint with a tensile strength of 395 MPa, 72% of that of the stainless steel was obtained. And almost no intermetallics were detected in Ti/V/Cu–V/Fe joint.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced materials and composites · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Titanium alloys and their machinability—a review10.1016/S0924-0136(96)00030-1 ↗
2. New application of stainless steel10.1016/S1006-706X(06)60028-9 ↗
3. Joining of gamma-TiAl to low alloy steel by electron beam welding10.1179/026708302225003659 ↗
4. Study of interface and base metal microstructures in explosive clad joint of Ti–5Ta–1.8Nb and 304L stainless steel10.1179/1362171810Y.0000000001 ↗
5. Phase transformation diffusion bonding of titanium alloy with stainless steel10.1016/j.matchar.2005.09.015 ↗
6. Evaluation of interface microstructure and mechanical properties of the diffusion bonded joints of Ti–6Al–4V alloy to micro-duplex stainless steel10.1016/j.matdes.2010.12.052 ↗
7. Interfacial properties of diffusion bonded Ti–6Al–4V to AISI 304 stainless steel by inserting a Cu interlayer10.1016/S1359-6462(01)01041-7 ↗
8. Joining of titanium to 304 stainless steel by friction welding10.1016/j.jmatprotec.2009.06.018 ↗
9. Joining of CP-Ti to 304 stainless steel using friction stir welding technique10.1016/j.matdes.2010.05.003 ↗
10. Interface microstructure in diffusion bonding of titanium alloys to stainless and low alloy steels10.1179/026708393790172376 ↗
11. Characterization of diffusion bonded joint between titanium and 304 stainless steel using a Ni interlayer10.1016/j.matchar.2007.05.015 ↗
12. Solid state diffusion bonding of titanium to steel using a copper base alloy as interlayer10.1016/j.jmatprotec.2008.06.014 ↗
13. Interfacial properties of diffusion bonded Ti–6Al–4V to AISI 304 stainless steel by inserting a Cu interlayer10.1007/s00170-008-1493-6 ↗
14. The Cu–Ti (copper–titanium) system10.1007/BF02880329 ↗
15. Interlayer engineering for dissimilar bonding of titanium to stainless steel10.1016/j.matlet.2010.02.024 ↗
16. The application of electron beam welding for the joining of dissimilar metals: an overview10.1016/0924-0136(95)02150-7 ↗
17. An investigation of fusion zone microstructure in electron beam welding of copper–stainless steel10.1016/j.msea.2006.03.096 ↗
18. Interfacial microstructure and strength of dissimilar joint Ti3Al/TC4 welded by the electron beam process10.1016/j.msea.2006.03.048 ↗
19. Characterisation of laser welded dissimilar Ti/steel joint using Mg interlayer10.1179/1362171812Y.0000000002 ↗
20. Effect of a copper filler metal on the microstructure and mechanical properties of electron beam welded titanium–stainless steel joint10.1016/j.matchar.2012.08.004 ↗
21. Electron beam welded high thickness Ti6Al4V plates using filler metal of similar and different composition to the base plate10.1016/S0042-207X(00)00454-1 ↗
22. Influence of the filler metal on the properties of Ti–6Al–4V electron beam weldments. Part I: welding procedures and microstructural characterization10.1016/j.vacuum.2009.08.003 ↗
23. Infrared brazing of Ti–6Al–4V and 17-4 PH stainless steel with a nickel barrier layer10.1007/BF02586140 ↗
24. Massalski · 1990
25. Fe–Ti–V (iron–titanium–vanadium)10.1007/BF02669155 ↗
26. Phase equilibria in the Cu–Fe–Ti system at 1123 K10.1016/0925-8388(94)01302-X ↗