Investigating the tribological behavior of bioinspired surfaces in agro-waste and alumina reinforced AA6063 matrix composites
Source abstract
Abstract
The tribological behavior of three bioinspired (BI) agro-waste ashes—bean pod ash (BPA), cassava peel ash (CPA), and coconut husk ash (CHA)—integrated as reinforcements in an alumina-reinforced AA6063 matrix hybrid and monolithic composite was investigated. Studies utilizing agro-wastes for bioinspired surfaces are limited despite these wastes posing significant environmental challenges. Consequently, there has been a growing effort to valorize these residues for sustainable engineering applications. This study uses a two-step stir-casting methodology to engineer bioinspired materials with lightweight properties, exceptional hardness, and wear-resistant characteristics. Microstructural investigations revealed a homogeneous distribution of natural and synthetic reinforcements within the AA6063 matrix. Lightweight AMCs were successfully fabricated, exhibiting densities ranging from 2.57 to 2.74 g/cm³ and hardness values between 81.28 and 107.47 BHN. The average surface roughness of these composites varied from 2.4 to 3.4 μm, with ANOVA tests confirming a statistically significant difference (p < 0.005). Wear rates and the coefficient of friction were observed to range from 2.52 x 10 −3 to 5.50 x 10 −3 mm³/m and 0.2476 to 0.5403, respectively. Reinforcing the AA6063 alloy with bioinspired agro-wastes significantly enhanced the hardness and tribological performance of the as-cast BI-AMCs. Notably, the wear rates and friction coefficients were significantly reduced, with the monolithic BI-AMCs demonstrating superior results. Furthermore, adding bioinspired agro-wastes, such as BPA, CPA, and CHA, improved the surface texture of AA6063 more effectively than Al 2 O 3 , leading to slightly smoother surfaces. These nuanced bioinspired tribological behaviors present opportunities for tailored load-bearing and aesthetic applications derived from agro-waste-based composites. This study advances our understanding of bioinspired tribological phenomena and paves the way for the development of innovative materials with diverse applications and enhanced performance.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Tribology and Wear Analysis · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Self-cleaning: from bio-inspired surface modification to MEMS/microfluidics system integration10.3390/mi10020101 ↗
2. Microstructures and mechanical properties of Al-Mg2Si-Si alloys resistance spot welded with Al-Si interlayers10.1016/j.jmrt.2019.07.043 ↗
3. Bio-inspired functional surfaces for advanced applications10.1016/j.cirp.2013.05.008 ↗
4. Envirobot: a bio-inspired environmental monitoring platform
5. Biotechnologies and bioinspired materials for the construction industry: an overview10.1080/19397038.2013.844741 ↗
6. Introduction to bioinspired surfaces engineering for biomaterials10.1039/D2TB90044K ↗
7. Bioinspired catalytic materials for energy-relevant conversions10.1038/nenergy.2017.131 ↗
8. Antibacterial surfaces developed from bio-inspired approaches10.1016/j.actbio.2012.01.011 ↗
9. Bioinspired hierarchical surface structures with tunable wettability for regulating bacteria adhesion10.1021/acsnano.5b04231 ↗
10. Biomimetic coatings to control cellular function through cell surface engineering10.1002/adfm.201300038 ↗
11. Superwettable surface engineering in controlling cell adhesion for emerging bioapplications10.1002/smtd.202000573 ↗
12. Bioinspired stimuli-responsive color-changing systems10.1002/adma.201707069 ↗
13. External stimuli responsive liquid-infused surfaces switching between slippery and nonslippery states: fabrications and applications
14. Mitigation of corrosion on magnesium alloy by predesigned surface corrosion
15. Research on metal corrosion resistant bioinspired special wetting surface based on laser texturing technology: a review
16. Novel corrosion-resistant behavior and mechanism of a biomimetic surface with switchable wettability on Mg alloy10.1016/j.cej.2021.130450 ↗
17. Bio-inspired graphene-based coatings on Mg alloy surfaces and their integrations of anti-corrosive/wearable performances10.1016/j.carbon.2018.09.047 ↗
18. Thrombogenic and inflammatory reactions to biomaterials in medical devices10.3389/fbioe.2020.00123 ↗
19. Medical device-induced thrombosis: what causes it and how can we prevent it?10.1111/jth.12961 ↗
20. Biomaterials/tissue interactions: possible solutions to overcome foreign body response10.1208/s12248-010-9175-3 ↗
21. Foreign body reaction to biomaterials10.1016/j.smim.2007.11.004 ↗
22. Engineering immunomodulatory biomaterials to tune the inflammatory response10.1016/j.tibtech.2016.03.009 ↗
23. Implications of the acute and chronic inflammatory response and the foreign body reaction to the immune response of implanted biomaterials
24. Directional, passive liquid transport: the Texas horned lizard as a model for a biomimetic ‘liquid diode
25. Microfluidics assisted fabrication of three-tier hierarchical microparticles for constructing bioinspired surfaces10.1021/acsnano.9b00245 ↗
26. Bio-inspired surface structures promote optical transmittance and hydrophobicity in cellulose-based fi lms for self-cleaning perovskite solar cells, Commun
27. Influence of green plantain peel ash and alumina reinforcement on the physio-mechanical properties of aluminium matrix hybrid composites10.4028/p-5CdJMw ↗
28. Utilisation of agro - industrial waste for sustainable green production : a review10.1007/s42398-021-00200-x ↗
29. From agricultural wastes to fermentation nutrients: a case study of 2,3-butanediol production
30. Agro waste reinforcement of metal matrix composites, a veritable sustainable engineering achievement, or an effort in futility? A critical review10.1088/2053-1591/ad5642 ↗
31. Experimental study on the wear behaviour of Al – Cu – Mg/bean pod ash nano-particles composites10.1007/s12666-015-0594-9 ↗
32. Potential of cassava peels as a sustainable coagulant aid for institutional wastewater treatment: characterisation, optimisation and techno-economic analysis10.1016/j.cej.2020.127642 ↗
33. Bioavailability of cyanide after consumption of a single meal of foods containing high levels of cyanogenic glycosides: a crossover study in humans10.1007/s00204-015-1479-8 ↗
34. The utilisation of coconut shell ash in production of hybrid composite : microstructural characterisation and performance analysis10.1016/j.jclepro.2023.136494 ↗
35. Utilization of cassava peel (manihot utilissima) waste as an adhesive in the manufacture of coconut shell (cocos nucifera) charcoal briquettes10.14710/ijred.2023.48432 ↗
36. The Production of dry beans in the World
37. The physio-mechanical properties of recycled low density polyethylene (RLDPE)/bean pod ash particulate composites10.1016/j.rinp.2014.05.003 ↗
38. Surface activity of solid particles with extremely rough surfaces10.1016/j.jcis.2007.09.066 ↗
39. Applications of bean pod and husk for remediation of water contamination: a review
40. Development and evaluation of recycled polypropylene and bean pod powder composite biomaterial for fused filament fabrication10.4236/ampc.2023.133003 ↗
41. Performance analysis of a connecting rod produced with Al-Cu-Mg/bean pod ash nanoparticles10.1007/s12633-015-9382-8 ↗
42. Zr4+ ions embedded chitosan-soya bean husk activated bio-char composite beads for the recovery of nitrate and phosphate ions from aqueous solution10.1016/j.ijbiomac.2019.02.100 ↗
43. Lignocellulosic-based materials from bean and pistachio pod wastes for dye-contaminated water treatment: optimization and modeling of indigo carmine sorption10.3390/polym14183776 ↗
44. High surface area activated carbon prepared from cassava peel by chemical activation10.1016/j.biortech.2005.04.029 ↗
45. Mesoporous activated carbon yielded from pre - leached cassava peels10.1186/s40643-021-00407-0 ↗
46. Morphological characteristics of cassava peel and its effect on the adsorption of heavy metal ions from aqueous media
47. Valorising cassava peel waste into plasticized polyhydroxyalkanoates blended with polycaprolactone with controllable thermal and mechanical properties10.1007/s10924-023-03167-4 ↗
48. Investigation of critical properties of Cassava (Manihot esculenta) peel and bagasse as starch-rich fibrous agro-industrial wastes for biodegradable food packaging
49. Sustainable use of cassava (Manihot esculenta) roots as raw material for biocomposites development10.1016/j.indcrop.2014.11.054 ↗
50. INFLUENCE OF SILICON CARBIDE-CASSAVA PEEL ASH WEIGHT RATIO ON THE MECHANICAL AND TRIBOLOGICAL CHARACTERISTICS OF Al-Mg-Si ALLOY HYBRID COMPOSITES
51. Improving fiber-matrix compatibility by surface modification of coconut coir fiber using white rot fungi10.4028/p-86979u ↗
52. Synthesis of coconut (cocos nucifera) husk fiber-silica composite as concrete additive
53. Chapter 5 - physical, morphological, structural, thermal, and tensile properties of coir fibers
54. A robust aqueous core–shell–shell coconut-like nanostructure for stimuli-responsive delivery of hydrophilic cargo10.1021/acsnano.9b03049 ↗
55. Sutrisno, 9 - evaluation of the effects of decay and weathering in cellulose-reinforced fiber composites
56. Emerging applications of green coconut: a promising lignocellulosic biomass10.1002/tqem.21974 ↗
57. Characteristics of activated carbon from coconut shell (Cocos nucifera) through chemical activation process10.1088/1755-1315/733/1/012134 ↗
58. Agro-management practices for sustainable coconut production
59. Adsorption of abattoir wastewater contaminants by coconut shell-activated carbon
60. Wear and microhardness behaviors of AA7075/SiC-BN hybrid nanocomposite surfaces fabricated by friction stir processing10.1016/j.ceramint.2020.03.274 ↗
61. Reinforcements, manufacturing techniques, and respective property changes of Al2O3/SiC based composites: a review10.1007/s12633-021-01108-1 ↗
62. Materials Science & Engineering A A novel (AlN + Si 3 N 4)/Al composite with well-balanced strength and ductility10.1016/j.msea.2018.04.053 ↗
63. Microstructure and mechanical behaviour of Al/SiC/agro-waste RhA hybrid metal matrix composite
64. Interface formation and bonding control in high-volume-fraction (TiC + TiB 2)/Al composites and their roles in enhancing properties10.1016/j.compositesb.2021.108605 ↗
65. Influence of addition of Grp/Al2O3p with SiCp on wear properties of aluminum alloy 6061-T6 hybrid composites via friction stir processing10.1016/S1003-6326(13)62593-5 ↗
66. Tribological performance of A206 aluminum alloy containing silica sand particles10.1016/j.triboint.2009.07.010 ↗
67. Microstructural analysis and properties of Al–Cu–Mg/bagasse ash particulate composites10.1016/j.jallcom.2010.02.190 ↗
68. Wear behaviour of Al-Si-Fe alloy/coconut shell ash particulate composites
69. Evaluation of the mechanical properties and corrosion behaviour of coconut shell ash reinforced aluminium (6063) alloy composites, Leonardo Electron
70. Microstructure, mechanical and fracture properties of groundnut shell ash and silicon carbide dispersion strengthened aluminium matrix composites
71. In-situ reinforcement of AA6063/Al2O3 hybrid composite: comparative wear and hardness evaluation of Manihot esculenta and green Plantago major particulates10.1007/s42452-024-05946-7 ↗
72. Fabrication characteristics and mechanical behaviour of aluminium alloy reinforced with Al2O3 and coconut shell particles synthesized by stir casting
73. Electrochemical investigation of the corrosion susceptibility of hybrid reinforced Al6063 with SiC and PKSA in 1.0 M sulfuric acid environment10.1002/eng2.12733 ↗
74. Mechanical and tribological behaviour of aluminium Al6061- coconut shell ash composite using stir casting pellet method
75. Tribological properties of A356.21RHA composites10.1016/S1005-0302(12)60069-3 ↗
76. Influence of bioceramic reinforcement on tribological behaviour of aluminium alloy metal matrix composites : experimental study and analysis10.1016/j.jmrt.2021.09.090 ↗
77. Mechanical properties of leaf ashes reinforced aluminum alloy metal matrix composites
78. Experimental investigations on wear and friction behaviour of Si3N4p reinforced heat-treated aluminium matrix composites produced using electromagnetic stir casting process10.1016/j.compositesb.2018.10.074 ↗
79. Analysis of dry sliding wear behaviour of Al6061/SiC/Al2O 3 hybrid metal matrix composites10.1016/j.compositesb.2013.04.051 ↗
80. Fabrication and characterization of ADC-12 hybrid composites utilizing lemon grass ash and boron nitride through stir-squeeze casting method10.1088/2053-1591/ad076f ↗
81. Influence of rice husk ash, cu, mg on the mechanical behaviour of aluminium matrix hybrid composites
82. Wear behaviour of aluminium 7075 — boron carbide- coconut shell fly ash reinforced hybrid metal matrix composites10.1088/2053-1591/ab4052 ↗
83. Development of aluminum composite reinforced with selected agricultural residues10.1007/s43939-023-00069-z ↗
84. Bean pod ash nanoparticles a promising reinforcement for aluminium matrix biocomposites10.1016/j.jmrt.2019.09.075 ↗
85. Effect of particle size on the fatigue behaviour of Al – Cu – Mg/bean pod ash particulate composites10.1007/s12666-014-0474-8 ↗
86. Study of physical , mechanical and machinability properties of aluminium metal matrix composite reinforced with coconut shell ash particulates
87. Development of aluminium matrix composite using coconut HUSK ash reinforcement
88. Advaith, Mechanical properties of coconut shell ash reinforced aluminium metal matrix composites10.1063/1.5092897 ↗
89. Characterization of heater-cooler blocks fabricated from aluminium wastes for steady-state thermal application10.4028/p-s7wbe2 ↗
90. Review on recent developments in bioinspired-materials for sustainable energy and environmental applications10.3390/su142416931 ↗
91. Bioinspired engineering of honeycomb structure – using nature to inspire human innovation10.1016/j.pmatsci.2015.05.001 ↗
92. Development of a low-cost thermal heater-cooler blocks using locally recycled waste
93. Enhanced mechanical and wear properties of aluminium-based composites reinforced with a unique blend of granite particles and boron carbide for sustainable material recycling
94. 2023
95. 2023
96. 2023
97. 2013
98. 1985
99. 1996
100. 2020