journal article·2017-04

Temperature and wear analysis in function of the cutting tool coating when drilling of composite structure: In situ measurement by optical fiber

Redouane Zitoune, Nicolas Cadorin, F. Collombet, Michal Šíma

Wear· Volume 376-377
Publisher page

Abstract

Abstract The aim of this paper was to study the influence of the nature coating and the machining parameters on the temperature of machining and tool wear of a new drilled 3D woven composite material used in carter fan of aircraft engine. For this various frictional contacts (tool/composite) have been analyzed for three types of cutting tools. The first tool is coated with a diamond layer and the other tools are coated with two new nano-composite multi-layers referenced as TiN/AlTiN/CrAlSiN and TiN/TiAlSiN/AlTiSiN. In addition, for the quantification of the in-situ temperature of drilling, an original technique based on the in-situ instrumentation of the cutting tool by optical fiber with four Braggs sensors is proposed. The evolution of the temperature of machining as a function of the machining parameters and frictional contacts were investigated. Also, the wear mechanisms were quantified in function of the number of drilled holes using Scanning Electron Microscopy (SEM). The results have shown that the feed rate and the nature of coating were the main factors which affect the temperature of machining. However, the spindle speed did not have any impact on the temperature of machining. It was also found that, when the drilling is conducted with a small feed (0.025 mm/rev) with TiN/TiAlSiN/AlTiSiN coating the temperature of machining was greater than the glass transition temperature of the composite. Moreover, tool wear mechanisms were found driven by abrasion phenomenon on the flank face and cutting edge.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Comparative analysis of drills for composite laminates10.1177/0021998311421690 ↗
2. Composites: part B experimental delamination analyses of CFRPs using different drill geometries10.1016/j.compositesb.2012.07.057 ↗
3. Machinability of carbon/epoxy composites by electrical discharge machining
4. Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite10.1016/j.wear.2015.01.019 ↗
5. Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid10.1177/0021998314553045 ↗
6. Effects of high speed in the drilling of glass fibre reinforced plastic: evaluation of the delamination factor10.1016/j.ijmachtools.2007.10.015 ↗
7. Delamination analysis of carbon fiber reinforced plastic (CFRP) composite plates by thermo graphic technique
8. Tribo-functional design of double cone drill implications in tool wear during drilling of copper mesh/CFRP/woven ply10.1016/j.wear.2013.01.046 ↗
9. Delamination and wear in drilling of carbon-fiber reinforced plastics composites using multilayer TiAlN/TiN PVD coated tungstencarbide tools10.1177/0731684412444653 ↗
10. Optimisation of machining parameters at high speed drilling of carbon fibre reinforced plastic (CFRP) laminates10.1016/j.compositesb.2012.01.007 ↗
11. Drilling carbon fiber-reinforced composite material at high speed10.1016/0043-1648(95)06831-7 ↗
12. Influence of machining process and machining induced surface roughness on mechanical properties of continuous fiber composites10.1007/s11340-014-9967-y ↗
13. Machinability and surface quality during high speed trimming of multi directional CFRP
14. Wear mechanisms and tool life management of WC–Co drills during dry high speed drilling of woven carbon fibre composites10.1016/j.wear.2009.01.031 ↗
15. Montoya · 2013
16. Some experimental investigations in the drilling of carbon fiber reinforced plastic (CFRP) composite laminates10.1016/S0890-6955(96)00095-8 ↗
17. Embedded FBGs and 3-D DIC for the stress analysis of a structural specimen subjected to bending10.1016/j.compstruct.2009.04.033 ↗
18. Contribution of embedded optical fiber with bragg grating in composite structures for tests-simulations dialogue10.1080/15376490600777616 ↗