Effect of particle hardness on mild–severe wear transition of hard second phase materials
Source abstract
Abstract
Abstract This study analyzes the effect of particle hardness on the transition from mild to severe abrasive wear. White cast iron with 1.9 wt% Cr with austenitic and martensitic matrices, white cast iron with 13.8 wt% Cr and 24.4 wt% Cr and mottled cast iron, and four types of abrasive with different hardness were used in pin-on-abrasive paper tests at 4.6 N of load. The microstructure of the alloys was characterized by optical microscopy and the micromechanisms of abrasive wear were characterized using scanning electron microscopy. The hardnesses of both the abrasive and the alloys were selected to obtain a H A / H range ratio (in which H A is the hardness of the abrasive and H is the alloys' hardness) much wider than the one reported in the literature until now. The relationship between wear rate and friction coefficient versus H A / H ratio was analyzed. The results show that when the H A / H ratio is less than 1.9, an increase in abrasive hardness produces significant increase in wear rate. However, when the ratio H A / H is more than 1.9, increasing the abrasive hardness has little effect on the wear rate. Comparing these results with the ones from the literature for homogeneous materials and hard second phase materials, the regions found in this study correspond to the severe wear region, the mild–severe wear transition, and a small mild wear region. A correlation between the friction coefficient and the H A / H ratio was found: the friction coefficient increases proportionally with the increase of H A / H to achieve a H A / H ratio of about 3.3. For H A / H values above 3.3 the friction coefficient is relatively constant.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Abrasive wear10.1016/S0141-5530(78)90054-7 ↗
2. Zum Gahr · 1987
3. Mild and severe wear of steels and cast irons in sliding abrasion10.1016/j.wear.2008.12.099 ↗
4. An experimental study of friction and wear during abrasion of metals
5. Effect of abrasive particle size on wear10.1016/0043-1648(65)90169-9 ↗
6. The empirical relationship between abrasive wear and applied conditions10.1016/0043-1648(66)90004-4 ↗
7. Influence of grit diameter and specimen size on wear during sliding abrasion10.1016/0043-1648(68)90574-7 ↗
8. On the size effect in abrasive and erosive wear10.1016/0043-1648(81)90062-4 ↗
9. Effect of abrasive size on wear of metallic materials and its relationship with microchips morphology and wear micromechanisms: part 210.1016/j.wear.2011.05.036 ↗
10. Particle size effect on abrasion resistance of mottled cast iron with different retained austenite contents10.1016/j.wear.2009.08.011 ↗
11. Effect of abrasive size on wear of metallic materials and its relationship with microchips morphology and wear micromechanisms: part 110.1016/j.wear.2011.01.078 ↗
12. Coronado · Effect of abrasive size on wear, InTech · 2012 · 167
13. The effects of particle characteristics on three-body abrasive wear10.1016/S0043-1648(01)00557-9 ↗
14. A study of abrasive wear under three-body conditions10.1016/0043-1648(61)90002-3 ↗
15. Principles of abrasive wear10.1016/0043-1648(74)90102-1 ↗
16. Abrasive wear of metals10.1016/S0301-679X(96)00063-1 ↗
17. Wear by hard particles10.1016/S0301-679X(98)00079-6 ↗
18. An explanation of the hardness differential needed for abrasion10.1016/0043-1648(81)90096-X ↗
19. The effect of hardness on the transition of the abrasive wear mechanism of steels10.1016/0043-1648(88)90102-0 ↗
20. Hutchings · 1992
21. Interpretations of indentation size effects10.1115/1.1469004 ↗
22. Analysis of the tip roundness effects on the micro- and macroindentation response of elastic–plastic materials10.1557/jmr.2009.0078 ↗
23. Indentation size effects in the nano- and micro-hardness of fcc single crystal metals10.1016/j.msea.2006.06.137 ↗
24. Correlation between dislocation density and nanomechanical response during nanoindentation10.1016/j.actamat.2011.11.034 ↗