journal article·2013-04

A study of the wear performance in a hip simulator of a metal–metal Co–Cr alloy with different boron additions

M. Alvarez-Vera, J.A. Ortega-Saenz, M.A.L. Hernandez-Rodríguez

Wear· Volume 301· Issue 1-2
Publisher page

Abstract

Abstract There has been a widely renewed interest in the use of metal-on-metal bearings for hip arthroplasties due to the medium-term results using contemporary conventional hip replacements. However, the search for new hip joint designs is targeted at younger and more active patients to optimise the performance of the bearing couple. The aim of this study was to investigate the wear behaviour of a modified Co–Cr alloy with boron additions. For this purpose, as-cast Co–Cr cups and heads were mated with different boron additions (0, 0.3, 0.6 and 1 B wt%) and tested in 4×10 6 cycles using the three-axial FIME II hip joint simulator under variable load profiles, and foetal bovine serum solution was as the lubricant. The wear was measured gravimetrically throughout the test. In addition, the bearing couples were characterised with metallographic techniques, confocal microscopy, scanning electronic microscopy, energy dispersive spectroscopy and roughness and hardness tests. The results showed an increase of the hard phases and wear resistance as the boron increased. In tribological terms, the results of this study showed the potential of this novel alloy as alternative for total hip prostheses.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Orthopaedic implants and arthroplasty · Orthopedic Infections and Treatments · Total Knee Arthroplasty Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. A comparison of friction in 28mm conventional and 55mm resurfacing metal-on-metal hip replacements10.1243/13506501JET234 ↗
2. The McKee–Farrar hip artroplasty10.1302/0301-620X.68B4.3733823 ↗
3. The ring total hip prosthesis10.2106/00004623-197254080-00007 ↗
4. Lessons of 30 years of total hip arthroplasty10.1097/00003086-199201000-00004 ↗
5. The benefits of metal-on metal total hip replacements
6. Metal on metal CoCrMo McKee–Farrar total hip arthroplasty: characteristics from a long-term follow-up study10.1007/BF00426058 ↗
7. Wear particles from metal-on-metal total hip replacements: effects of implant design and implantation time10.1243/09544119JEIM112 ↗
8. A tribological study of cobalt chromium molybdenum alloys used in metal-on-metal resurfacing hip arthroplasty10.1016/S0043-1648(03)00046-2 ↗
9. A hip joint simulator study of the performance of metal-on-metal joints
10. Influence of simulator kinematics on the wear of metal-on-metal hip prostheses10.1243/0954411011533481 ↗
11. Disappointing short-term results with the DePuy ASR XL metal-on-metal total hip arthroplasty10.1016/j.arth.2011.08.022 ↗
12. Metal-on-metal hip arthroplasty going, going, gone—affirms10.1302/0301-620X.94B11.30745 ↗
13. Metal-on-metal hip arthroplasty going, going, gone—opposes10.1302/0301-620X.94B11.30622 ↗
14. Whole blood metal Ion concentrations in correlation with activity level in three different metal-on-metal bearings10.1016/j.arth.2009.11.007 ↗
15. The clinical significance of metal ion release from cobalt–chromium metal-on-metal hip joint arthroplasty10.1243/09544119JEIM78 ↗
16. Mathew · Tribocorrosion behavior of CoCrMo alloy for hip prosthesis as a function of loads: a comparison between two testing systems · 2011 · 271 · 1210
17. Yan · Effect of metallic nanoparticles on the biotribocorrosion behaviour of metal-on-metal hip prostheses · 2009 · 267 · 683
18. Wear of cast metal-metal pairs for total replacement hip prostheses10.1016/j.wear.2005.02.080 ↗
19. Boron influence on wear resistance in nickel-based alloys10.1016/j.wear.2008.12.046 ↗
20. Development of a hip wear simulation rig including micro-separation10.1016/j.wear.2007.01.097 ↗
21. Force actions transmitted by joints in the human body10.1098/rspb.1976.0004 ↗
22. ISO/DIS 14242-1 Draft International Standard, Implants for surgery-wear of total hip joint prostheses-part 1: loading and displacement parameters for wear-testing machines and corresponding environmental conditions for test, (2001).
23. Quantitative analysis of the wear and wear debris from low and high carbon content cobalt chrome alloys used in metal on metal total hip replacements10.1023/A:1026473723777 ↗
24. Hip Joint Simulator Study of the Performance of Metal-on-Metal Joints
25. Analysis of fluid film lubrication in artificial hip joint replacements with surfaces of high elastic modulus10.1243/0954411971534359 ↗
26. Metal-on-metal bearings surfaces: materials, manufacture, design, optimization, and alternatives10.1243/095441105X68953 ↗
27. Importance of head diameter, clearance, and cup wall thickness in elastohydrodynamic lubrication analysis of metal-on-metal hip resurfacing prostheses10.1243/09544119JEIM172 ↗
28. An in vitro study of the reduction in wear of metal-on-metal hip prostheses using surface engineered femoral heads10.1243/09544110260138709 ↗
29. ‘Severe’ wear challenge to ‘as-cast’ and ‘double heat-treated’ large-diameter metal-on-metal hip bearings10.1243/09544119JEIM81 ↗
30. Tribological principles in metal-on-metal hip joint design10.1243/095441105X63255 ↗
31. The effect of ‘running-in’ on the tribology and surface morphology of metal-on-metal Birmingham hip resurfacing device in simulator studies10.1243/09544119JEIM63 ↗
32. Head replacement, head rotation, and surface damage effects on metal-on-metal total hip replacements: a hip simulator study10.1243/095441105X69097 ↗
33. Current concepts of metal-on-metal hip resurfacing10.1016/j.ocl.2005.02.007 ↗
34. Micro-abrasion mechanisms of cast CoCrMo in simulated body fluids10.1016/j.wear.2009.03.005 ↗
35. Metal wear particle characterization from metal on metal total hip replacements: transmission electron microscopy study of periprosthetic tissues and isolated particles10.1002/(SICI)1097-4636(199810)42:1<103::AID-JBM13>3.0.CO;2-M ↗
36. An accurate and extremely sensitive method to separate, display, and characterize wear debris part 2: metal and ceramic particles10.1007/s11999-011-2058-9 ↗
37. Metal-on-metal hip simulator study of increased wear particle surface area due to ‘severe’ patient activity10.1243/09544119JEIM93 ↗