journal article·2016-12

Wear performance of hierarchically structured alumina reinforced by hybrid graphene encapsulated alumina nanofibers

Irina Hussainova, Janis Baronins, Maria Drozdova, Maksim Antonov

Wear· Volume 368-369
Publisher page

Abstract

Abstract Nowadays, the lightweight composites with superior mechanical and tribological properties to be used for several applications in automotive and aerospace industries attract much research interest. Graphene added into ceramic-based composites is believed to positively contribute into sliding wear resistance of materials. To study an effect of graphenated fillers, dry sliding wear behaviour of spark plasma sintered alumina and its hierarchically structured composites reinforced by hybrid graphene encapsulated alumina nanofibres were tested against alumina at a reciprocating mode under mild (0.98 N) and severe (4.90 N) loading conditions for 72 h and 1 h, respectively. The tests were conducted at an average velocity of 0.006 m s −1 in air for the composites with different content (0−15 wt%) of the fillers corresponding to 0−1.5 wt% of graphene. Benchmarked against the pure alumina, the composites added with 1−5 wt% of hybrid nanofibres exhibited at least threefold higher wear resistance under mild conditions along with insignificant change in coefficient of friction; whilst under severe conditions, the wear resistance was found to increase up to 90% along with a decrease in the coefficient of friction only for the composite added by 1 wt% of fibres. Wear reduction for the composites with a low content of hybrid nanofibres might be attributed to increase in hardness together with increase in indentation fracture toughness. The relative index of brittleness is shown to serve as a wear performance indicator only under mild environment.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Tribology and Wear Analysis · Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Review of graphene–ceramic matrix composites10.1179/174367613X13764308970581 ↗
2. Highly transparent α-alumina obtained by low cost high pressure SPS10.1016/j.ceramint.2012.10.012 ↗
3. Thermal shock resistance of two micro-structured alumina obtained by natural sintering and SPS10.1016/j.ceramint.2013.06.045 ↗
4. Mechanical properties of graphene platelet-reinforced alumina ceramic composites10.1016/j.ceramint.2013.01.041 ↗
5. A novel approach to electroconductive ceramics filled by graphene covered nanofibers10.1016/j.matdes.2015.10.148 ↗
6. Graphene reinforced alumina nano-composites10.1016/j.carbon.2013.07.086 ↗
7. Corrigendum: exceptionally strong and robust millimeterscale graphene–alumina composite (2014 Nanotechnology 25 355701)10.1088/0957-4484/25/43/439501 ↗
8. Interfacial stress transfer in a graphene monolayer nanocomposite10.1002/adma.200904264 ↗
9. Hybrid graphene/alumina nanofibers for electrodonductive zirconia10.4028/www.scientific.net/KEM.674.15 ↗
10. Unoxidized graphene/alumina nanocomposite: fracture- and wear-resistance effects of graphene on alumina matrix10.1038/srep05176 ↗
11. Tribological performance of Graphene/Carbon nanotube hybrid reinforced Al2O3 composites10.1038/srep11579 ↗
12. The effect of graphene reinforcement on the mechanical properties of Al2O3 ceramics rapidly sintered by high-frequency induction heating10.1016/j.ijrmhm.2014.10.011 ↗
13. Electrically conductive alumina–carbon nanocomposites prepared by Spark Plasma Sintering10.1016/j.jeurceramsoc.2009.05.045 ↗
14. Wear behavior of graphene/alumina composite10.1016/j.ceramint.2015.02.061 ↗
15. Tribological properties of silica–graphene nano-platelet composites10.1016/j.ceramint.2014.04.046 ↗
16. Toughening in graphene ceramic composites10.1021/nn200319d ↗
17. Microstructure and fracture toughness of graphene nanosheets/alumina composites10.1016/j.ceramint.2014.05.107 ↗
18. Coupled thermal analysis of novel alumina nanofibers with ultrahigh aspect ratio10.1016/j.tca.2013.10.010 ↗
19. Graphene-encapsulated aluminium oxide nanofibers as a novel type of nanofillers for electroconductive ceramics10.1016/j.jeurceramsoc.2015.06.011 ↗
20. Direct CVD growth of multi-layered graphene closed shells around alumina nanofibers10.4028/www.scientific.net/KEM.674.77 ↗
21. Hardness, toughness, and brittleness: an indentation analysis10.1111/j.1151-2916.1979.tb19075.x ↗
22. The effect of fine erodent retained on the surface during erosion of metals, ceramics, plastic, rubber and hardmetal10.1016/j.wear.2016.02.018 ↗
23. Effect of loading system inertia on tribological behaviour of ceramic–ceramic, ceramic–metal and metal–metal dry sliding contacts10.1016/j.triboint.2013.03.025 ↗
24. Running-in: art or engineering?10.1007/BF02834123 ↗
25. How common is the steady-state? The implications of wear transitions for materials selection and design
26. The wear behaviour of oxide ceramics – a review10.1023/B:JMSC.0000045601.49480.79 ↗
27. Micromechanical properties and erosive wear performance of chromium carbide based cermets10.1016/j.wear.2008.12.104 ↗
28. The relationship between wear behaviour and brittleness index in engineering ceramics and dispersion-reinforced ceramic composites
29. Wear of advanced ceramics10.1016/S0043-1648(02)00240-5 ↗
30. Raman spectrum of graphene and graphene layers10.1103/PhysRevLett.97.187401 ↗
31. Effect of thermo-elastic residual stresses on erosive performance of cermets with core–rim structured ceramic grains10.1016/j.wear.2009.01.019 ↗
32. Ripple formation induced in localized abrasion10.1103/PhysRevB.68.115416 ↗
33. Investigations of sand–water induced erosive wear of AISI 304L stainless steel pipes by pilot-scale and laboratory-scale testing10.1016/S0043-1648(03)00095-4 ↗
34. Atomistic simulations of structural and thermodynamic properties of bilayer graphene10.1103/PhysRevB.81.235439 ↗
35. Multiscale analysis of the interfacial mechanical behavior for composite of carbon nanotube and α -alumina10.1155/2014/237097 ↗
36. Microstructural design of ceramic–metal composites for tribological applications10.4028/www.scientific.net/KEM.334-335.125 ↗