Experimental study of the effects of temperature and humidity on the wear and damage behavior of U71Mn rail steel
Source abstract
Abstract
Wheel-rail interfaces operating in open systems are constantly affected by environmental factors, such as water, relative humidity, temperature, leaves, and sand. In this study, a twin-disc rolling-sliding friction and wear test device with a controlled environmental chamber was used to conduct experiments to study the influence of high temperature and humidity on the wear and damage behavior of U71Mn rail steel. The results showed that surface oxidation of rails increased with increasing temperature and humidity. The surface oxides and very humid air provided lubrication that could reduce wear. With increasing temperature and humidity, the trend of the friction coefficient of the rail samples was basically consistent with that of the plastic deformation layer. The wear of rail samples first decreased and then increased with increasing humidity. However, with increasing temperature, the wear of the rail samples first increased and then decreased. With increasing temperature and humidity, the crack length on the rail surface gradually increased and extended to the center of the material, which made the competition between wear and rolling contact fatigue more intense. When the wear was less than rolling fatigue, rail surfaces underwent severe cracking and peeling, which resulted in the loss of a large amount of surface material.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Railway Engineering and Dynamics · Mechanical stress and fatigue analysis · Adhesion, Friction, and Surface Interactions
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Mapping the friction between railway wheels and rails focusing on environmental conditions[J]10.1016/j.wear.2014.12.028 ↗
2. Friction between wheel and rail: a pin-on-disc study of environmental conditions and iron oxides[J]10.1007/s11249-013-0220-0 ↗
3. A review on wear between railway wheels and rails under environmental conditions[J]10.1115/1.4044464 ↗
4. Presence and role of the third body in a wheel-rail contact[J]10.1016/j.wear.2004.03.068 ↗
5. Effect of humidity, temperature and railhead contamination on the performance of friction modifiers: pin-on-disk study[J]10.1177/0954409712452239 ↗
6. An experimental study of high speed wheel-rail adhesion characteristics in condition on full scale roller rig[C]
7. Wear between wheel and rail: a pin-on-disc study of environmental conditions and iron oxides[J]10.1016/j.wear.2015.02.057 ↗
8. Influence of leaf, humidity and applied lubrication on friction in the wheel-rail contact: pin-on-disc experiments[J]10.1243/0954409042389364 ↗
9. Wear by plastic ratchetting[J]10.1016/S0043-1648(97)00083-5 ↗
10. Ratcheting and fatigue-led wear in rail-wheel contact [J]10.1046/j.1460-2695.2003.00703.x ↗
11. Effect of sliding speed and hardness on wear behavior and mechanism of AISI H13 steel[J]
12. Effect of the presence of moisture at the wheel–rail interface during dew and damp conditions[J]10.1177/0954409717706251 ↗
13. Simulation and understanding the wet-rail phenomenon using twin disc testing[J]10.1016/j.triboint.2019.03.067 ↗
14. Full-scale testing of low adhesion effects with small amounts of water in the wheel/rail interface[J]10.1016/j.triboint.2019.105907 ↗
15. Influence of low temperature environment on the adhesion characteristics of wheel-rail contact[J]10.1016/j.triboint.2018.05.037 ↗
16. On the wear and damage characteristics of rail material under low temperature environment condition[J]10.1016/j.wear.2017.10.011 ↗
17. Study on the wear and damage behaviors of hypereutectoid rail steel in low temperature environment[J]
18. Experimental study on the wear and damage of wheel-rail steels under alternating temperature conditions[J]10.1016/j.wear.2021.203829 ↗
19. Exceptionally prolonged extreme heat waves over South China in early summer 2020: the role of warming in the tropical Indian Ocean[J]10.1016/j.atmosres.2022.106335 ↗
20. Influence of ambient humidity on the adhesion and damage behavior of wheel–rail interface under hot weather condition[J]
21. Risk of increasing temperature due to climate change on high-speed rail network in Spain [J]
22. Role of ambient temperature in the adhesion and damage characteristics of wheel/rail interface during rolling-sliding contact
23. New insight on wheel flange/rail gauge lubrication: effect of lasered microtexture shapes on the wear and fatigue behaviour of wheel/rail steels [J]
24. The steady state wear behaviour of pearlitic rail steel under dry rolling–sliding contact conditions[J]10.1016/0043-1648(94)06533-0 ↗
25. Wear mechanisms and transitions in railway wheel steels[J]
26. Study of rolling contact fatigue, rolling and sliding wear of class B wheel steels against R350HT and R260 rail steels under dry contact conditions using the twin disc setup[J]10.1016/j.triboint.2022.107711 ↗
27. Tribofilm formation and mild wear by tribo-sintering of nanometer-sized oxide particles on rubbing steel surfaces [J]10.1016/j.wear.2006.03.046 ↗
28. Understanding the effect of water on the transient decomposition of zinc dialkyldithiophosphate (ZDDP)[J]10.1016/j.triboint.2021.106855 ↗
29. Experimental investigation on the effect of operating speeds on wear and rolling contact fatigue damage of wheel materials[J]10.1016/j.wear.2016.08.006 ↗
30. Influence of original microstructure on rolling contact fatigue property of D2 wheel steel
31. Experimental study on wear properties of wheel and rail materials with different hardness values[J]10.1016/j.wear.2021.203831 ↗
32. Microstructure evolution of railway pearlitic wheel steels under rolling-sliding contact loading[J]10.1016/j.triboint.2020.106685 ↗
33. Study on wear and rolling contact damage mechanism between quenched U75V rail and wheels with different microstructures