journal article·2023-06Open access

Wear performance of the Fe-Ni-WC-based impregnated diamond bit with Mo2C-coated diamonds: Effect of the interface layer

Xinyue Mao, Qingnan Meng, Mu Yuan, Sifan Wang, Jinlong Wang, Shiyin Huang, Baochang Liu, Ke Gao

Wear· Volume 522

Abstract

With the increased difficulty of drilling into hard rock in the petroleum industry , the demand for higher performance and efficiency of impregnated diamond bits (IDB) has risen sharply. This paper describes the effect of Mo 2 C coatings on the wear properties and working efficiency in Fe-Ni-WC-based IDBs. The Mo 2 C-coated diamonds were obtained via the molten salts method. The diamond/Fe-Ni-WC IDBs were prepared by vacuum hot-press sintering method. Laboratory drilling tests of IDBs were carried out to evaluate the wear performance of the two drilling bits. An ultra-depth field 3D imaging microscope was performed to measure the protrusion height of diamond particles on the bottom surface of IDBs. The results manifested that the addition of the Mo 2 C coating contributed to increasing the protrusion height of diamonds, meaning the enhancement of the interface strength between the diamonds and matrix. The drilling rate of the Fe-Ni-WC-based IDB with Mo 2 C-coated diamonds is 18% higher than that of Fe-Ni-WC-based IDB with uncoated diamonds, accompanied by increased wear loss.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tunneling and Rock Mechanics · Advanced materials and composites · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Matrix material for a new 3D-printed diamond-impregnated bit with grid-shaped matrix10.1016/j.ijrmhm.2019.04.017 ↗
2. Effect of CaF2 and hBN on the mechanical and tribological properties of Fe-based impregnated diamond bit matrix10.1016/j.ijrmhm.2018.04.011 ↗
3. Incorporating stratigraphic boundary uncertainty into reliability analysis of slopes in spatially variable soils using one-dimensional conditional Markov chain model10.1016/j.compgeo.2019.103321 ↗
4. Mechanical properties and microstructural characteristics of WC-bronze-based impregnated diamond composite reinforced by nano-NbC10.1016/j.triboint.2022.107777 ↗
5. Effect of Fe-based pre-alloyed powder on the microstructure and holding strength of impregnated diamond bit matrix10.1016/j.ijrmhm.2018.11.015 ↗
6. New utilization approach of microwave thermal energy: preparation of metallic matrix diamond tool bit by microwave hot-press sintering10.1016/j.jallcom.2018.03.183 ↗
7. Wear behavior of bionic impregnated diamond bits10.1016/j.triboint.2015.08.039 ↗
8. 3-D Finite element modelling of diamond pull-out failure in impregnated diamond bits10.1016/j.diamond.2016.11.006 ↗
9. Influence of B4C coating on graphitization for diamond/WC-Fe-Ni composite10.1016/j.ijrmhm.2020.105208 ↗
10. Fabrication of Fe-based diamond composites by pressureless infiltration10.3390/ma9121006 ↗
11. A review of the diamond retention capacity of metal bond matrices10.3390/met8050307 ↗
12. Sintering of polycrystalline diamond cutting tools10.1016/j.matdes.2005.09.018 ↗
13. Wear of cemented tungsten carbide percussive drill–bit inserts: laboratory and field study10.1016/j.wear.2017.05.010 ↗
14. Influence of the impact sintering temperature on the structure and properties of samples from the different iron powders10.1016/j.apt.2016.10.007 ↗
15. Sintering of nanodispersed iron powder
16. Application of pre-alloyed powders for diamond tools by ultrahigh pressure water atomization10.1016/S1003-6326(16)64393-5 ↗
17. Consolidation of diamond tools using Cu-Co-Fe based alloys as metallic binders10.1179/003258901666211 ↗
18. Study hot pressed Fe-diamond composites graphitization10.1016/j.ijrmhm.2012.03.015 ↗
19. Enhancement of oxidation resistance via a self-healing boron carbide coating on diamond particles
20. Decreasing the sintering temperature of diamond-bit matrix material by the addition of the element P10.1016/S0924-0136(97)00248-3 ↗
21. Doping Fe-based diamond tool matrix composites with a rare-earth element10.3103/S1063457609060082 ↗
22. The use of coated diamonds in diamond impregnated tools
23. Evolution of interface carbide diamond brazed with filler alloy containing Cr10.1016/j.diamond.2018.10.009 ↗
24. Performance of diamond drill bits with hybrid nanoreinforced Fe-Ni-Mo binder10.1007/s00170-018-03262-0 ↗
25. Hybrid metallic nanocomposites for extra wear-resistant diamond machining tools10.1016/j.ijrmhm.2017.10.017 ↗
26. Effect of molybdenum on diamond deposition and adhesion10.1016/j.tsf.2004.05.119 ↗
27. Preparation of the gradient Mo layers on diamond grits by spark plasma sintering and their effect on Fe-based matrix diamond composites10.1016/j.jallcom.2016.10.172 ↗
28. Mo 2 C coating on diamond: different effects on thermal conductivity of diamond/Al and diamond/Cu composites10.1016/j.apsusc.2017.01.078 ↗
29. Application of polymeric drilling fluids for reducing wearing of drill bit10.1016/j.jics.2021.100324 ↗
30. Diamond tools for machining of granite and their wear
31. Measurements of tool wear parameters using machine vision system
32. Measurement of bit-rock interface temperature and wear rate of the tungsten carbide drill bit during rotary drilling10.1007/s40544-019-0330-2 ↗
33. Tribological properties of copper alloy-based composites reinforced with tungsten carbide particles10.1016/j.wear.2011.01.015 ↗
34. Study of a new impregnated diamond bit for drilling in complex, highly abrasive formation10.1016/j.petrol.2019.106831 ↗