journal article·2023-06

Investigation of surface characteristics on post processed additively manufactured biomaterial through magnetorheological fluid assisted finishing process

Atul Singh Rajput, Manas Das, Sajan Kapil

Wear· Volume 522
Publisher page

Abstract

Additive Manufacturing ( AM) is recently used to manufacture biomedical implants as the customized fabrication of the desired complex shapes is easily achievable with reduced manufacturing time and material waste. However, the poor surface quality of additively manufactured products is a major concern over biomaterials` functionality. Magnetorheological Fluid Assisted Finishing ( MFAF ) process is an advanced surface finishing process used to improve the workpiece surface quality without altering surface topography. Selective Laser Melting ( SLM) is utilized in the presented study to fabricate biomaterials using SS316L powder, and surface quality is further enhanced through the MFAF process. However, average surface roughness ( R a) only delivers the details regarding the average altitude of peaks and depth of valleys from the central line. Therefore, kurtosis ( R ku) and skewness ( R sk) analysis of the polished surface are also carried out to determine detailed surface characteristics. The bio-tribology analysis of the polished surface of the AM implant determines its sustainability inside the human body. Hence, a wear test utilizing the pin-on-disc process is performed on the finished surface to determine the efficiency of the polishing process during tribological contact of the biomaterials with the bone. Further, the improved surface roughness parameters ( R a, R ku, and R sk) after the MFAF of AM implant`s surface are also investigated with an optical profilometer and scanning electron microscope. The MFAF process produced a highly polished surface on the biomaterial and a final R a value of 32.46 nm is attained after polishing from its initial value of 8.32 μm with a decrease in wear rate (i.e., from 9.86 × 10 −5 mm 3/min to 0.46 × 10 −5 mm 3/min). The value of kurtosis less than three (i.e., 0.79) indicates that the flat peaks are generated on the surface irregularities after MFAF. Similarly, the negative skewness (i.e., Rsk = −0.28) represents that the number of peaks is less than the valleys. It indicates that the chances of wear out of the surface irregularities from the workpiece on their tribological contact are very low.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Bone Tissue Engineering Materials · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Improving the fatigue performance of porous metallic biomaterials produced by Selective Laser Melting10.1016/j.actbio.2016.10.005 ↗
2. Selective laser melting10.1002/latj.201290018 ↗
3. Parametric analysis of the selective laser melting process10.1016/j.apsusc.2007.02.088 ↗
4. Review of selective laser melting: materials and applications10.1063/1.4935926 ↗
5. Microstructure and mechanical properties of selective laser melted magnesium10.1016/j.apsusc.2011.03.004 ↗
6. Binding mechanisms in selective laser sintering and selective laser melting10.1108/13552540510573365 ↗
7. Selective laser melting in biomedical manufacturing
8. On optimization of surface roughness of selective laser melted stainless steel parts: a statistical study10.1007/s11665-014-0993-9 ↗
9. Defect Formation mechanisms in selective laser melting: a review10.1007/s10033-017-0121-5 ↗
10. Porosity testing methods for the quality assessment of selective laser melted parts10.1016/j.cirp.2016.04.054 ↗
11. Microstructure and mechanical properties of selective laser melted biomaterial Ti-13Nb-13Zr compared to hot-forging10.1016/j.msea.2018.04.001 ↗
12. Improvement of corrosion resistance of SS316L manufactured by selective laser melting through subcritical annealing10.1016/j.corsci.2019.108353 ↗
13. Morsiya · 2020
14. A comparative investigation on the mechanical properties and cytotoxicity of Cubic, Octet, and TPMS gyroid structures fabricated by selective laser melting of stainless steel 316L10.1016/j.jmbbm.2022.105151 ↗
15. Formation of SS316L single tracks in micro selective laser melting: surface, geometry, and defects10.1155/2019/9451406 ↗
16. Dowson · 1985
17. Wear mechanisms of UHMWPE in total joint replacements10.1016/0043-1648(94)07027-X ↗
18. Metal-on-metal bearings and hypersensitivity in patients with artificial hip joints: a clinical and histomorphological study10.2106/00004623-200501000-00006 ↗
19. Pseudotumours associated with metal-on-metal hip resurfacings10.1302/0301-620X.90B7.20213 ↗
20. Laser polishing of parts built up by selective laser sintering10.1016/j.ijmachtools.2007.01.013 ↗
21. Enhancing surface finish of additively manufactured titanium and cobalt chrome elements using laser based finishing10.1016/j.phpro.2016.08.021 ↗
22. Laser polishing of 3D printed mesoscale components10.1016/j.apsusc.2017.01.211 ↗
23. Surface quality and material removal in magnetic abrasive finishing of selective laser melted 316L stainless steel10.1016/j.jmapro.2019.07.044 ↗
24. Material removal mechanism of additively manufactured components finished using magnetic abrasive finishing10.1016/j.promfg.2018.07.047 ↗
25. Electropolishing and shaping of micro-scale metallic features10.3390/mi13030468 ↗
26. Investigations on the toolpath strategies for CNC magnetorheological fluid assisted finishing (MFAF) process10.1007/s00170-022-09307-9 ↗
27. Rajput · 2022 · 26 · 339
28. Investigations on a hybrid chemo-magnetorheological finishing process for freeform surface quality enhancement10.1016/j.jmapro.2022.07.015 ↗
29. Rajput · 2022 · 1
30. Investigations on the trochoidal toolpath for processing the biomaterial through magnetorheological fluid assisted finishing process10.1016/j.jmapro.2022.02.055 ↗
31. Rajput · 2022
32. Experimental investigation into nano-finishing of β-TNTZ alloy using magnetorheological fluid magnetic abrasive finishing process for orthopedic applications10.1016/j.jmrt.2021.01.046 ↗
33. Wear characteristics of Ti–Nb–Ta–Zr and Ti–6Al–4V alloys for biomedical applications10.1016/j.wear.2004.04.001 ↗
34. Correlation between standard roughness parameters skewness and kurtosis and tribological behaviour of contact surfaces10.1016/j.triboint.2011.11.008 ↗
35. Enhancement of abrasion and corrosion resistance of duplex stainless steel by laser shock peening10.1016/j.jmatprotec.2012.01.023 ↗
36. Ultra-high molecular weight Polyethylene: influence of the chemical, physical and mechanical properties on the wear behavior
37. Characterization of implant materials in fetal bovine serum and sodium sulfate by electrochemical impedance spectroscopy. I. Mechanically polished samples10.1002/jbm.10329 ↗
38. Tribological performance of selective laser melted 316L stainless steel10.1016/j.triboint.2018.07.021 ↗