Low-alloyed steel with superior dry abrasive wear resistance and mechanical properties processed via steel mold casting
Source abstract
Abstract
Wear parts, such as tools, need to possess a combination of hardness, strength, and toughness along with high wear resistance. This study introduces a lean Fe94.2Cr0.3Mo0.4Mn1.5Ni3.0C0.6 (wt%) alloy specifically designed for cast wear parts. The research evaluates its microstructure, mechanical properties, and abrasive wear characteristics using various analysis methods. The chemical composition of the FeCrMoMnNiC alloy in combination with the applied steel mold casting lead to a microstructure composed of fine martensite (85 vol%) and austenite (15 vol%) as shown by quantitative analysis with X-ray diffraction. Quasi-static compression tests show pronounced work hardening from the compressive yield strength (σ y0.2 = 1660 MPa) to the compressive strength (σ cf = 5090 MPa) with good deformability (ε max = 32%). For comparing the abrasive wear and mechanical performance, a commercially available martensitic steel was used as reference material. Abrasive wear studies using a SiC abrasive revealed a significantly lower wear rate for the novel alloy (5.9 ∙ 10 −3 mm 3 (Nm) −1 ) compared to the reference steel (14.2 ∙ 10 −3 mm 3 (Nm) −1 ), which is caused by the fine, multiphase microstructure. The predominant abrasive wear mechanism for the FeCrMoMnNiC was identified as micro ploughing. However, the wear traces also indicate micro cutting, and additional micro fatigue as consequence of repeated deformation. A friction-induced transformation from austenite to martensite was observed, evidenced by the reduced austenite content at the surface detected via grazing incidence X-ray diffraction and transmission-electron backscatter diffraction, which also showed surface deformation. These findings indicate, that the FeCrMoMnNiC alloy combining superior mechanical and wear properties, is a promising material for heavy industry wear applications. • Investigated FeCrMoMnNiC alloy with austenitic-martensitic microstructure showing superior mechanical and wear properties. • Wear-induced phase transformation observed by X-ray diffraction and transmission-electron backscatter diffraction. • Transformation of austenite into martensite promotes strengthening and deformability under wear and compression load. • Micro ploughing as predominant mechanism results in a low abrasive wear rate. • Presented alloy offers high potential to improve sustainability and service life of tools.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. The materials science behind sustainable metals and alloys10.1021/acs.chemrev.2c00799 ↗
2. Strategies for improving the sustainability of structural metals10.1038/s41586-019-1702-5 ↗
3. Mesquita · 2017
4. Influence of tribology on global energy consumption, costs and emissions10.1007/s40544-017-0183-5 ↗
5. Solidification of high speed steels10.1179/095066001101528411 ↗
6. Effect of cerium addition on microstructure and mechanical properties of high-strength Fe85Cr4Mo8V2C1 cast steel10.1016/j.msea.2016.07.114 ↗
7. Roberts · 1998
8. Global energy consumption due to friction and wear in the mining industry10.1016/j.triboint.2017.05.010 ↗
9. Study and characteristic of abrasive wear mechanisms
10. Stachowiak · 2011
11. A newly designed high-strength tool steel with high wear and Corrosion resistance10.3390/ma16051941 ↗
12. A review of key factors affecting the wear performance of medium manganese steels10.3390/met13071152 ↗
13. Abrasive wear resistance of some commercial abrasion resistant steels evaluated by laboratory test methods10.1016/j.wear.2009.08.005 ↗
14. Enhancing wear resistance of 100Cr6 bearing steels by new heat treatment method10.1007/s11661-021-06556-3 ↗
15. Microstructures, heat treatment, and properties of boron-alloyed tool steels10.1002/srin.201900416 ↗
16. Reciprocating sliding wear of the sintered 316L stainless steel with boron additions10.1016/j.wear.2019.01.027 ↗
17. Effect of short-term tempering on microstructure and mechanical properties of high-strength FeCrMoVC10.1016/j.actamat.2012.04.041 ↗
18. High strain rate behavior, transformation-induced plasticity and fracture toughness characterization of cast and additionally tempered Fe85Cr4Mo8V2C1 alloy manufactured using a rapid solidification technique10.1007/s10853-012-6637-2 ↗
19. Effects of alloying elements on microstructure, hardness, and fracture toughness of centrifugally cast high-speed steel rolls10.1007/s11661-005-0141-0 ↗
20. Abrasive wear protection in material handling: mechanism-based combination of lab-experiments for optimal material selection
21. Bhadeshia · 2017
22. 2.9 heat treatment of tool steels
23. Machining of hard materials10.1016/S0007-8506(16)30003-8 ↗
24. Requirements on tools and machines when machining hard materials
25. Design of low hardness abrasion resistant steels10.1016/j.wear.2013.01.002 ↗
26. Wear behaviour of some low alloyed steels under combined impact/abrasion contact conditions10.1016/S0043-1648(01)00712-8 ↗
27. Thermomechanical processing of advanced high strength steels10.1016/j.pmatsci.2018.01.006 ↗
28. Novel Fe-0.3Cr-0.4Mo-1.5Mn–3Ni-0.6C tool steel with superior properties under quasi-static and dynamic loading
29. Nečas · 2012 · vol. 10 · 181
30. Whole powder pattern decomposition methods and applications: a retrospection10.1154/1.2135315 ↗
31. WinPLOTR: a windows tool for powder diffraction pattern analysis10.4028/www.scientific.net/MSF.378-381.118 ↗
32. Quantitative powder X-ray diffractometry phase analysis of silicon nitride materials by a multiline, mean-normalized-intensity method10.1111/j.1151-2916.1994.tb07118.x ↗
33. Über die Temperaturabhangigkeit der Gitterparameter von Eisen, Kobalt und Nickel im Bereich hoher Temperaturen
34. Partial molar volumes from high-temperature lattice parameters of iron–carbon austenites10.1179/msc.1970.4.1.219 ↗
35. Analysis of the static and dynamic properties of wear-resistant Hardox 600 steel in the context of its application in working elements10.2478/msp-2021-0007 ↗
36. Analysis of wear properties of hardox steels in different soil conditions10.3390/ma15217622 ↗
37. The influence of heat treatment and deep rolling on the mechanical properties and integrity of AISI 1060 steel10.1016/j.jmatprotec.2014.07.013 ↗
38. An investigation into roller burnishing10.1016/S0890-6955(00)00019-5 ↗
39. A study of the micro- and nanoscale deformation behavior of individual austenitic dendrites in a FeCrMoVC cast alloy using micro- and nanoindentation experiments10.1063/1.4945403 ↗
40. Detection of the indentation-size-effect (ISE) and surface hardening by analysis of the loading curvature C10.1016/j.ijsolstr.2016.01.024 ↗
41. Zum Gahr · 1987
42. An X-ray microanalysis study of the partition of manganese in 6 and 9% Mn cryogenic steels and its influence on the stability of austenite dispersed in a tempered martensitic matrix10.1016/0001-6160(81)90020-1 ↗
43. Carbon partitioning into austenite after martensite transformation10.1016/S1359-6454(03)00059-4 ↗
44. Stabilization mechanisms of retained austenite in transformation-induced plasticity steel10.1007/s11661-001-0240-5 ↗
45. Austenite stabilization through manganese enrichment10.1016/j.scriptamat.2010.09.040 ↗
46. The abrasive-corrosive wear of stainless steels10.1016/0043-1648(81)90169-1 ↗
47. Dry sliding wear of nanostructured carbide-free bainitic steels – effect of oxidation-dominated wear
48. Reibungsinduzierter martensit in austenitischen Fe-Mn-C-stählen
49. Martens · 2022
50. X-ray interactions: photoabsorption, scattering, transmission, and reflection at E = 50-30,000 eV, Z = 1-9210.1006/adnd.1993.1013 ↗
51. Role of S and Se atoms on the microstructural properties of kesterite Cu2ZnSn(SxSe1−x)4 thin film solar cells10.1039/C5CP07577G ↗
52. The temperature of rubbing bodies; part 2, the distribution of temperatures10.1016/0043-1648(88)90249-9 ↗
53. A novel operando approach to analyze the structural evolution of metallic materials during friction with application of synchrotron radiation10.1016/j.actamat.2020.06.049 ↗
54. Time-dependant microstructural evolution and tribological behaviour of a 26 wt% Cr white cast iron subjected to a destabilization heat treatment10.1007/s12540-022-01276-8 ↗
55. Friction-induced martensitic transformation in austenitic manganese steels10.1016/0043-1648(86)90134-1 ↗
56. Grain boundary segregation in Fe–Mn–C twinning-induced plasticity steels studied by correlative electron backscatter diffraction and atom probe tomography10.1016/j.actamat.2014.09.041 ↗
57. Impact of nanodiffusion on the stacking fault energy in high-strength steels10.1016/j.actamat.2014.04.062 ↗
58. Friction-induced phase transformations and evolution of microstructure of austenitic stainless steel observed by operando synchrotron X-ray diffraction10.1016/j.actamat.2022.118033 ↗
59. Evolution of friction-induced microstructure of SUS 304 meta-stable austenitic stainless steel and its influence on wear behavior10.1016/j.wear.2008.12.068 ↗
60. The effect of strain-induced martensitic transformation on mechanical properties of TRIP steel10.1016/j.matdes.2007.02.019 ↗
61. The role of the austenite grain size in the martensitic transformation in low carbon steels10.1016/j.matdes.2019.107625 ↗
62. Achieving exceptional wear resistance in a crack-free high-carbon tool steel fabricated by laser powder bed fusion without pre-heating10.1016/j.jmst.2023.02.012 ↗
63. Transformation-induced plasticity (TRIP) in advanced steels: a review
64. Advanced high strength steels (AHSS) for automotive applications − tailored properties by smart microstructural adjustments10.1002/srin.201700210 ↗
65. Numerical analysis of stresses in mine excavator bucket10.1134/S1062739115020131 ↗