journal article·2005-01

Performance of WC–VC–Co thermal spray coatings in abrasion and slurry erosion tests

C.N. Machio, G. Akdogan, M.J. Witcomb, S. Luyckx

Wear· Volume 258· Issue 1-4
Publisher page

Abstract

Thermal spray coatings based on tungsten carbide are widely used in wear applications. This paper presents results obtained from commercial WC-12 wt.%Co and WC-17 wt.%Co as well as experimental WC-10 wt.%VC-12 wt.%Co and WC-10 wt.%VC-17 wt.%Co coatings. The coatings have been deposited on stainless steel substrates using a high pressure high velocity oxy-fuel (HP/HVOF) Tafa® JP 5000 thermal spraying system. They have all been tested under identical conditions in order to compare their resistance to abrasion and slurry erosion. Similar tests have been carried out previously in our laboratory [H.L. de Villiers-Lovelock, S. Luyckx, Preliminary investigation on the potential of VC-WC-Co HP/HVOF powders and coatings, in: C.C. Berndt (Ed.), Proceedings of the First International Thermal Spray Conference, Montreal, Canada, 8-11 May 2000, pp. 647-656] [1] but gave inconclusive results which were found due to the VC-containing powders (WC-VC-Co) not being optimal. The tests have now been repeated with optimized WC-VC-Co powders. The present results show that the WC-VC-Co coatings produced with the optimized powders exhibit higher abrasion resistance then commercial WC-Co coatings. In slurry erosion, the best performance of the VC-containing coatings is as good as that of the commercial WC-Co coatings. The role of VC and cobalt in the wear process of the coatings is discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. Preliminary investigation on the potential of VC-WC-Co HP/HVOF powders and coatings
2. Microstructural evaluation of tungsten carbide-cobalt coatings10.1007/BF02659015 ↗
3. The application of thermal spray coatings for combating slurry erosion in centrifugal pumps
4. Microstructural aspects of the strength and hardness of cemented tungsten carbide
5. S Luyckx, Vanadium carbide in hardmetals, vol. 2, XVth CMMI Congress, Johannesburg, SAIMM, 1994, pp. 11–13.
6. Fine grained WC–VC–Co hardmetal10.1179/pom.1996.39.3.210 ↗
7. A comparison between ultrafine WC-Co and fine WC-VC-Co alloys10.1504/IJMPT.2000.001254 ↗
8. Characterisation of new WC-VC-Co thermal spray powders
9. S. Luyckx, D.J. Whitefield, M.J. Witcomb, L.A. Cornish, The development of WC–VC–Co hardmetal: a review of past work and new results, Adv. Powder Metall. Part. Mater. (1998) 1-85–1-91.
10. C. Machio, S. Luyckx, private communication, 2003.
11. The mechanical properties of wear-resistant coatings. II: Experimental studies and interpretation of hardness10.1016/0040-6090(87)90120-9 ↗
12. The slurry erosion of ultrafine tungsten carbide–cobalt
13. Slurry erosion of WC–Co cermets and ceramics10.1080/05698198508981604 ↗
14. Effect of composition on the (V, W)C constitution in V-W-C-Co alloys
15. S. Broccardo, An investigation into the corrosion resistance of WC–VC–Co hardmetals, M.Sc. Dissertation, University of the Witwatersrand, 2003