journal article·2016-12Open access

Lubricated sliding wear of SAE 1045 and SAE 52100 steel against alumina in the presence of biodiesel, diesel and a 50:50 blend of those fuels

Victor Velho de Castro, Luiz Antonio Mazzini Fontoura, Juliano Dornelas Benfica, Marcus Seferin, Joyson Luiz Pacheco, Carlos Alexandre dos Santos

Wear· Volume 368-369

Abstract

Abstract The purpose of this work was to evaluate the sliding wear characteristics of SAE 1045 and SAE 52100 steels with different microstructures in the presence of pure biodiesel, a biodiesel-diesel blend (50% diesel+50% biodiesel) and commercial diesel fuel. Non-lubricated tests (dry) were also performed for comparison. For SAE 1045, samples were given a hardening heat treatment (austenitization at 830 °C and water quenching). For SAE 52100, the heat treatment was austenitization at 850 °C followed by oil quenching. Tempering at 100 °C and 300 °C was used for SAE 1045, and tempering at 100 °C and 200 °C was used for SAE 52100. As a result, the samples had four different hardness and microstructure combinations: tempered martensite in SAE 1045 and tempered martensite with chromium carbides in SAE 52100. Wear testing was performed using a pin-on-disk tribometer, 1.8 m/s sliding speed, 14.7 N load and 4400 m sliding distance following the ASTM G99-04 standard. Wear track surfaces were characterized using microindentation hardness and scanning electron microscopy. The results exhibited a tendency to decrease wear width, volume loss and wear coefficient when adding biodiesel to diesel for both SAE 1045 and SAE 52100 steels. Martensite produced by heat treatments increased the wear resistance. For both SAE 1045 and SAE 52100 steels, abrasive wear is dominant in both dry and lubricated conditions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Lubricants and Their Additives · Tribology and Wear Analysis · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Biodiesel: an overview10.1590/S0103-50532005000800003 ↗
2. Technical aspects of biodiesel production by transesterification10.1016/j.rser.2004.09.002 ↗
3. G. Knothe, “Designer” biodiesel: optimizing fatty ester composition to improve fuel properties, Energy and Fuels, vol. 22, 2008, pp.1358–1364.10.1021/ef700639e ↗
4. M.A. Fazal, A.S.M.A. Haseeb, H.H. Masjuki, Biodiesel feasibility study: an evolution of material compatibility; performance; emission and engine durability. Renewable and Sustainable Energy Reviews, vol. 15, 2011. pp.1314–1324.10.1016/j.rser.2010.10.004 ↗
5. Wear and friction behaviour of Si3N4 ceramics under diesel and biodiesel lubrication10.1016/j.jmrt.2013.01.006 ↗
6. Friction and wear characteristics of Calophyllum inophyllum biodiesel10.1016/j.indcrop.2015.05.042 ↗
7. Wear coefficient of tungsten carbide against hot-work tool steel disc with two different pin settings10.1016/j.wear.2004.01.014 ↗
8. A test methodology for the determination of wear coefficient10.1016/j.wear.2005.01.026 ↗
9. Microstructural aspects determining the adhesive wear of tool steels10.1016/j.wear.2005.07.001 ↗
10. Wear characteristic of palm olein as lubricant in different rotating speed10.1016/j.proeng.2013.12.162 ↗
11. Wear between wheel and rail: a pin-on-disc study of environmental conditions and iron oxides10.1016/j.wear.2015.02.057 ↗
12. A pin-on-disc study of the tribology characteristics of sintered versus standard steel gear materials10.1016/j.wear.2015.01.032 ↗
13. Investigation of friction and wear characteristics of palm biodiesel10.1016/j.enconman.2012.12.002 ↗
14. Micro- and nanometric wear evaluation of metal discs used on determination of biodiesel fuel lubricity10.1590/S1516-14392014005000101 ↗
15. The relation between lubricity and electrical properties of low sulfur diesel and diesel/biodiesel blends10.1016/j.fuel.2013.09.026 ↗
16. Gerdau Special Steels – Catalog, 2014. 〈www.ggdmetals.com.br/aco-especiais〉, 〈www.ggdmetals.com.br/aco-construcao-mecanica〉.
17. ASTM G99−04, Standard test method for wear testing with a pin-on-disk apparatus, Am. Soc. Test. Mater., ASM Society, United States, 2004, 5 p.
18. EN 14103, Fats and oil derivatives – fatty acid methyl esters (FAME) – determination of ester and linolenic acid methyl esters contents, European Standard, European Committee for Standardization, Belgium, 2003, 18p.
19. ASTM D 7371-12, Standard test method for determination of biodiesel (fatty acid methyl esters) content in diesel fuel oil using mid infrared spectroscopy (FTIRATR- PLS Method), Am. Soc. Test. Mater., ASM Society, United States, 2012, 10p.
20. ASTM E3−11, Standard guide for preparation of metallographic specimens, Am. Soc. Test. Mater., ASM Society, United States, 2011, 8p.
21. ASTM E18-03, Standard test methods for Rockwell hardness and Rockwell superficial hardness of metallic materials, Am. Soc. Test. Mater., ASM Society, United States, 2004, 22p.
22. ASTM E384−99, Standard test method for microindentation hardness of materials, Am. Soc. Test. Mater., ASM Society, United States, 2000, 24p.
23. Stachowiak · 2005 · 802
24. Effect of temperature on tribological properties of palm biodiesel10.1016/j.energy.2009.12.001 ↗