Carbide-tipped bit wear patterns and productivity with concrete drilling
Source abstract
Abstract
Abstract Drilling into concrete with carbide-tipped bits using a hammer drill is a physically demanding task performed in commercial construction for setting anchors and rebar. Bit wear will not only decrease productivity (rate of penetration) but can also increase drill handle vibration, noise and dust exposure to workers. The purpose of this study was to evaluate the relationships between geometric patterns of bit wear and rate of penetration. Image analysis methods were used to quantify 13 geometric parameters of the carbide tip at various levels of wear, and the changes in the geometric parameters were then compared to changes in penetration rate. Two different bit designs were studied. New bits were worn by repeatedly drilling into aged concrete. Penetration rate was determined on a test bench system programmed to drill into aged concrete to a specific depth under force control while the time to complete the hole was measured. Increasing fluke slope, increasing shoulder rounding, and decreasing bit width were highly correlated to reduced productivity. The findings have practical value for contractors and bit manufacturers in providing a method to identify concrete bits that should be replaced due to reduced cutting ability.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tunneling and Rock Mechanics · Drilling and Well Engineering · Advanced machining processes and optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Pelmear · 1992
2. An examination of the vibration transmissibility of the hand-arm system in three orthogonal directions10.1016/j.ergon.2014.11.001 ↗
3. OSHA (Occupational Safety and Health Administration), Occupational Exposure to Respirable Crystalline Silica; Final Rule, Federal Register, 81(58), 25 March 2016, pp. 16285–16890. Available at 〈https://www.osha.gov/silica/〉.
4. Effect of bit wear on hammer drill handle vibration and productivity10.1080/15459624.2017.1316385 ↗
5. The effects of bit wear on respirable silica dust, noise and productivity: a hammer drill bench study10.1093/annweh/wxx041 ↗
6. A summary of methods applied to tool condition monitoring in drilling10.1016/S0890-6955(02)00040-8 ↗
7. Statistical characteristics of drill wear and drill life for the standardized performance tests
8. Tool life determination based on the measurement of wear and tool force ratio variation10.1016/j.ijmachtools.2004.04.018 ↗
9. Evolution during time of tool wear and cutting forces in the case of hard turning with CBN inserts10.1016/j.jmatprotec.2005.03.038 ↗
10. Drag bit wear model10.2118/16699-PA ↗
11. OSHA (Occupational Safety and Health Administration), Occupational Exposure to Respirable Crystalline Silica; Final Rule, Federal Register, 81(58), 25 March 2016, pp. 16285–16890. Available at 〈https://www.osha.gov/silica/〉.
12. Coring basalt under Mars low pressure conditions
13. Wear characteristics of PDC pin and hybrid core bits in rock drilling10.1016/0043-1648(95)06646-2 ↗
14. Quality and wear behavior of graded polycrystalline diamond compact cutters10.1016/j.ijrmhm.2015.12.009 ↗
15. Wear performances and mechanisms of ultrahard polycrystalline diamond composite material grinded against granite10.1016/j.ijrmhm.2015.07.014 ↗
16. B.D. Brandon, J. Cerkovnik, E. Koskie, B.B. Bayoud, F. Colston, R.I. Clayton, M.E. Anderson, K.T. Hollister, J. Senger, R. Niemi, R, First revision to the IADC fixed cutter dull grading system, in: Proceedings of the SPE/IADC Drilling Conference, 1992.10.2118/23939-MS ↗
17. Compact core drilling in basalt rock using PCD tool inserts: wear characteristics and cutting forces10.1016/j.jmatprotec.2010.03.023 ↗
18. ISRM suggested method for determining the abrasivity of rock by the CERCHAR abrasivity test10.1007/s00603-013-0518-0 ↗
19. A new test bench system for hammer drills: validation for handle vibration10.1016/j.ergon.2016.08.001 ↗
20. Comite ́ Europe ́ en de Normalisation (CEN), Concrete– Part 1: Specification, Performance, Production and Conformity, European Committee for Standardization EN 206-1:2013, Brussels, Belgium, 2013.
21. International Organization for Standardization (ISO), Cement—Test Methods—Determination of Strength, ISO 679, Geneva, Switzerland, 2009.
22. International Organization for Standardization (ISO), Hand-Held Portable Power Tools – Test Methods for Evaluation of Vibration Emission – Part 10: Percussive Drills, Hammers and Breakers, ISO 28927-10, Geneva, Switzerland, 2011.
23. Taylor · 1907
24. Wear characteristics of polycrystalline diamond compact drill bits in small diameter rock drilling10.1115/1.3231231 ↗
25. Core drilling in reinforced concrete using polycrystalline diamond (PCD) cutters: wear and fracture mechanisms10.1016/j.ijrmhm.2008.11.014 ↗