journal article·2004-09

Effects of intermediate layers on the tribological behavior of DLC coated 2024 aluminum alloy

Xia Lifang, Yan Zhaohui, Liao Jiaxuan

Wear· Volume 257· Issue 5-6
Publisher page

Abstract

Abstract DLC coated 2024 aluminum alloy samples having four different intermediate layers prepared by different plasma-based ion implantation modes. The composition and structures of DLC coated samples were investigated by X-ray photoelectron spectroscopy (XPS), laser Raman spectroscopy and glancing angle X-ray diffraction (GXRD). Knoop micro-hardness and nano-hardness of the layers had been measured too. The tribological behaviors of these samples were investigated by ball on disk frictional tester and scanning electron microscopy (SEM). Results show that the stable friction coefficients of these four samples are nearly same and about 0.1, but the sliding cycles of holding stable friction coefficient are different, they increase according to the order of samples (a)–(d) sequentially. For these four samples, whether the loading was 1 or 20 N, the stable friction coefficient is nearly same, but the sliding cycles of holding stable friction coefficient are different, while the cycles of holding stable friction coefficient as loading 20 N are less than as loading 1 N for same sample. The wear rate of the samples decreases according to the order of samples (a)–(d) sequentially. The SEM morphologies of the worn tracks are dependent on the intermediate layer structures and friction test conditions, the characters of the wear are rubbing, abrasive wear and delamination wear, but for samples (a) and (b) a slight adhesive wear appears as loading 20 N.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (14)

Show source-provided references
1. Plasma source ion implantation of oxygen and nitrogen in aluminum10.1116/1.587329 ↗
2. Structure and wear behavior of nitrogen-implanted aluminum alloys10.1116/1.587330 ↗
3. Tribological behavior of aluminum alloys surface layer implanted with nitrogen ions by plasma immersion ion implantation10.1016/S0043-1648(98)00252-X ↗
4. Tribological behavior of diamond-like carbon: effects of preparation conditions and annealing10.1016/0257-8972(91)90112-A ↗
5. Friction and wear of diamond and diamond-like carbon coatings10.1016/S0257-8972(07)80061-2 ↗
6. Tribological behavior of carbon coatings deposited on steel substrates by plasma assisted chemical vapour deposition10.1016/0925-9635(94)90113-9 ↗
7. A new PBIID processing system supplying RF and HV pulses through a single feed-through10.1016/S0257-8972(02)00111-1 ↗
8. Diamond-like carbon coating for aluminum 390 alloy-automotive applications10.1016/S0257-8972(97)00061-3 ↗
9. Friction and wear behavior of the modified layer of aluminum alloy implanted with nitrogen and titanium by plasma source ion implantation
10. The tribological properties of ALN/DLC modifying layer on aluminum alloy implanted with nitrogen and carbon plasma based ion implantation
11. Structure and frictional characteristics of Ti–6Al–4V plasma-based ion implanted with nitrogen then acetylene10.1016/S0043-1648(98)00391-3 ↗
12. Metal plasma source ion implantation using a UBM cathode10.1016/S0257-8972(00)00577-6 ↗
13. An Al/TiN layer of aluminum alloy implanted by PBII and its wear-resistant properties
14. The structure and tribological characteristic for aluminum alloy implanted with N/Ti by PBII