journal article·2009-06

Microstructural alterations within thermal spray coatings during highly loaded diesel engine tests

M. Hahn, R. Theissmann, B. Gleising, W. Dudzinski, A. Fischer

Wear· Volume 267· Issue 5-8
Publisher page

Abstract

Abstract The good wear characteristics of thermal spray coatings are related to structural, productional, and topographical properties. Finally, the alteration of the microstructure in different contact zones is essential for mild wear conditions that will guarantee a long-life cycle because it reveals the ability of the material to adjust to the current load situation. Previous studies have shown that in diverse tribosystems an in situ formation of a nanocrystalline layer together with mechanical mixing maintains long-lasting, wear resistant surfaces with low wear rates. This investigation exemplifies results from a cylinder that was run in a road test motor. The relevant piston ring positions that fully describe the tribosystem have to be defined at the combustion chamber (CC), top dead centre (TDC), stroke and bottom dead centre (BDC). Transmission electron microscopy (TEM) and energy-filtered transmission electron microscopy (EFTEM) are used to analyse these contact zones in terms of microstructure and chemistry. Nanocrystalline surface layers up to a thickness of 100 nm occurred in all areas of contact whereas subsurface zones revealed differing microstructural changes. Thus the influence of thermal impact and different mechanical load conditions in a motor cylinder are evident. EFTEM elemental mappings verify the incorporation of elements that stem from lubrication or combustion residues.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Lubricants and Their Additives · Tribology and Wear Analysis · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. Motor vehicle application of thermally sprayed specialty coatings
2. K. Bobzin, F. Ernst, J. Zwick, T. Schlaefer, C. Verpoort, K. Nassenstein, A. Schwenk, F. Schreiber, T. Wenz, G. Flores, M. Hahn, Coating bores of light metal engine blocks with a nano-composite material using the plasma transfered wire arc thermal spraying process, JTST 17 (3) (2008), 344–351.10.1007/s11666-008-9188-y ↗
3. Automobile engine tribology—approaching the surface10.1016/S0043-1648(00)00375-6 ↗
4. Investigation of fundamental wear mechanisms at the piston ring and cylinder wall interface in internal combustion engines10.1243/13506501JET254 ↗
5. Structure and mechanical properties of tribologically induced nanolayers10.1016/j.wear.2005.02.086 ↗
6. Wear processes in sliding systems10.1016/0043-1648(84)90013-9 ↗
7. Mikrotribometrie im Maschinenbau10.1002/mawe.200300678 ↗
8. Origins of the wear resistance of AlSi cylinder bore surfaces studies by surface analytical tools10.1016/j.triboint.2007.01.015 ↗
9. Hahn · 2007 · vol. 39 · 137
10. Thermal spray of cylinder bores with the ford PTWA process
11. Domke · 1971
12. Relation of certain quantum chemical parameters to lubrication behaviour of solid oxides10.3390/i6060203 ↗
13. Compatability between tribological surfaces and lubricant additives—how friction and wear reduction can be controlled by surface/lube synergies10.1016/j.triboint.2007.01.019 ↗
14. Gerve · 1998 · vol. 7
15. Characterization of anti-wear films formed from fresh an aged engine oils10.1016/j.wear.2006.12.026 ↗
16. Understanding the composition and low friction tribofilm formation/removal in boundary lubrication10.1016/j.triboint.2007.02.001 ↗
17. Nanoscale evolution of sliding metal surfaces during running-in10.1007/s11249-007-9216-y ↗
18. Microstructure of tribologically induced nanolayers produced at ultra-low wear rates10.1016/j.wear.2007.01.127 ↗
19. Verschleißmechanismen bei moderater und extremer Grenzreibung10.1002/mawe.200400823 ↗
20. Characterization of wear debris of systems operated under low wear-rate conditions10.1016/j.wear.2005.03.025 ↗