Reciprocative sliding wear of ZrO2–TiCN composites against WC-Co cemented carbide
Source abstract
Abstract
ZrO2-based composites with 40 vol.% TiC0.5N0.5 addition were processed from both nanocrystalline and micrometer sized TiC0.5N0.5 starting powders by hot pressing. Flat samples were manufactured and finished by wire electrical discharge machining (EDM) in order to investigate their sliding-wear behavior against a WC-Co cemented carbide. Reciprocative sliding experiments were performed under unlubricated conditions using a small-scale pin-on-plate tribometer. The worn surfaces of the investigated composites were analyzed by X-ray diffractometry (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and surface topography. Post-mortem obtained wear volume loss was compared to online measured wear depth. Wear rates were correlated to sliding distance and material parameters and microstructural characteristics. The experimental results revealed a significant dependence of the wear resistance of the ZrO2-based composites on loading conditions and the nature of the secondary phase. © 2008 Elsevier B.V. All rights reserved.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Advanced ceramic materials synthesis · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Processing and microstructure of high-pressure consolidated ceramic nanocomposites10.1016/j.scriptamat.2004.08.022 ↗
2. Wear-resistant ultra-fine-grained ceramics10.1016/j.actamat.2004.09.020 ↗
3. The transition from mild to severe wear in alumina during sliding10.1016/0956-7151(92)90212-W ↗
4. Wear and wear transition mechanisms of ceramics10.1016/0043-1648(95)06800-7 ↗
5. Microscopic observations of abrasive wear of polycrystalline alumina10.1016/0043-1648(75)90152-0 ↗
6. Chemical and mechanical mechanisms in wear of sapphire on steel10.1111/j.1151-2916.1966.tb13239.x ↗
7. Observations on the sliding wear of ceramics10.1080/05698198508981618 ↗
8. Transformation toughening in zirconia-containing ceramics10.1111/j.1151-2916.2000.tb01221.x ↗
9. Ceramic steel?10.1038/258703a0 ↗
10. Development and characterization of Y2O3-stabilized ZrO2 (Y-TZP) composites with TiB2, TiN, TiC, and TiC0.5N0.510.1111/j.1151-2916.1999.tb02147.x ↗
11. Development and characterization of ZrO2–TiC0.5N0.5 nanocomposites
12. Toughness optimisation of ZrO2–TiB2 composites10.4028/www.scientific.net/KEM.206-213.1177 ↗
13. Hard, tough and strong ZrO2–WC composites from nanosized powders10.1016/j.jeurceramsoc.2004.01.015 ↗
14. Titanium carbonitride–zirconia composites: formation and characterization10.1016/0955-2219(91)90119-K ↗
15. Investigation of material removal mechanisms in EDM of composite ceramic materials10.1016/j.jmatprotec.2004.02.013 ↗
16. Wire EDM machining of Si3N4-, ZrO2- and Al2O3-based ceramics10.2526/ijem.10.33 ↗
17. Influence of secondary electro-conductive phases on the electrical discharge machinability and frictional behavior of ZrO2-based ceramic composites10.1016/j.jmatprotec.2008.01.020 ↗
18. Electrically conductive ZrO2–TiN composites10.1016/j.jeurceramsoc.2005.10.010 ↗
19. Electrical discharge machining of ZrO2/TiN particulate composite10.1179/096797800680767 ↗
20. Machining of low electrical conductive materials by wire electrical discharge machining (WEDM)10.1016/j.jmatprotec.2003.11.055 ↗
21. The effect of microstructure on the wear transition of zirconia toughened alumina10.1016/0043-1648(93)90514-M ↗
22. Influence of fracture toughness on the wear resistance of yttria-doped zirconium oxide10.1111/j.1151-2916.1989.tb06110.x ↗
23. Sliding wear of electrically conductive ZrO2-WC composites against WC-Co cemented carbide10.1007/s11249-008-9326-1 ↗
24. Friction and wear of ceramics10.1016/0301-679X(95)00039-7 ↗
25. Wear transitions in monolithic alumina and zirconia-alumina composites10.1016/0043-1648(94)07030-X ↗
26. The stress field created by a circular sliding contact10.1115/1.3625051 ↗
27. Quantitative wear maps as a visualization of wear mechanism transitions in ceramic materials10.1016/0043-1648(89)90058-6 ↗
28. Wear mechanisms in ceramics
29. Al2O3–ZrO2 debris life cycle during wear: effects of third body on the wear and friction10.1016/S0043-1648(96)07455-8 ↗
30. Sliding friction of ceramics: mechanical action of wear debris10.1007/BF00575394 ↗
31. Genesis and role of wear debris in sliding wear of ceramics10.1016/S0043-1648(00)00465-8 ↗
32. Wear mechanisms and wear rate in a high temperature dry friction of AISI H11 tool steel: influence of debris circulation10.1016/j.wear.2006.12.032 ↗
33. On the role of interfacial debris morphology in a conforming contact tribosystems10.1016/0043-1648(91)90371-Z ↗