Tribological behavior of polyacetal composite lubricated in sodium hypochlorite solution
Source abstract
Abstract
Abstract Sodium hypochlorite (NaClO) solution is the most widely used disinfectant in the food industry. If NaClO solution can be used as a lubricant, the maintenance cost is reduced and the food safety is warrantied. Hypothetically, the concentration of the available chlorine in the solution affects the tribological behaviors. In this study, we investigated the tribological behavior of a composite of polyacetal (POM) resin and rice bran ceramics (RBC) in a lubricating solution of NaClO with two concentrations. The mean friction coefficient was higher in NaClO solution with 25 mg/L available chlorine than in purified water and in NaClO with 2500 mg/L available chlorine. The wear resistance of the composite was also degraded in the presence of 25 mg/L available chlorine. From the investigations of the tribological behavior of an RBC disk, the wear in the lower available chlorine was considered to be affected by degradation of the carbon parts. Although we should improve the tribological properties in the presence of 25 mg/L available chlorine, the POM/RBC composite had a sufficient potential to use in NaClO solution as a tribomaterial.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tribology and Wear Analysis · Polymer Nanocomposites and Properties · Lubricants and Their Additives
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. Sodium hypochlorite and formalin as antiviral agents against nuclear-polyhedrosis virus in larvae of the cabbage looper10.1016/0022-2011(68)90268-1 ↗
2. Effective shelf-life of prepared sodium hypochlorite solution10.1016/S0099-2399(06)81040-X ↗
3. Mechanisms of actions of sodium hypochlorite in cleaning and disinfection processes10.4265/bio.11.147 ↗
4. Effect of ionomers on mechanical properties, morphology, and rheology of polyoxymethylene and its blends with methyl methacrylate–styrene–butadiene copolymer10.1016/j.eurpolymj.2004.10.046 ↗
5. Tribological behaviour of polyacetals10.1016/0043-1648(80)90132-5 ↗
6. The tribological behaviour of different engineering plastics under dry friction conditions10.1016/j.matdes.2006.11.012 ↗
7. Parameters influencing the running-in and long-term tribological behaviour of polyamide (PA) against polyacetal (POM) and steel10.1016/j.wear.2012.04.017 ↗
8. Friction and wear behavior of 18 polymers in contact with steel in environments of air and water10.1016/0043-1648(91)90378-8 ↗
9. Development of hard porous materials “RB ceramics” made of rice bran
10. Polymer composites filled with RB ceramics particles as low friction and high wear resistant filler10.2474/trol.5.19 ↗
11. Tribological behavior of polyacetal composite filled with rice bran ceramics particles under water lubrication10.1177/0021998317740198 ↗
12. Chemical treatments to reduce postharvest spoilage of fruits and vegetables10.1007/BF02868689 ↗
13. Electrolyzed water as a disinfectant for fresh-cut vegetables10.1111/j.1365-2621.1999.tb15079.x ↗
14. Predictive models for available chlorine depletion and total microbial count reduction during washing of fresh‐cut spinach10.1111/j.1365-2621.2001.tb15187.x ↗
15. The hardness of solids10.1088/0034-6683/1/3/I01 ↗
16. Role of wear particles in severe–mild wear transition10.1016/j.wear.2005.02.102 ↗
17. Effect of the active chlorine and the pH on consumption of graphite anode in chlor-alkali cells10.1149/1.2401784 ↗
18. Adsorption of benzene, toluene, ethylbenzene and p-xylene by NaOCl-oxidized carbon nanotubes10.1016/j.colsurfa.2009.10.025 ↗