Fatigue performance of additively manufactured meta-biomaterials: The effects of topology and material type
Source abstract
Abstract
Additive manufacturing (AM) techniques enable fabrication of bone-mimicking meta-biomaterials with unprecedented combinations of topological, mechanical, and mass transport properties. The mechanical performance of AM meta-biomaterials is a direct function of their topological design. It is, however, not clear to what extent the material type is important in determining the fatigue behavior of such biomaterials. We therefore aimed to determine the isolated and modulated effects of topological design and material type on the fatigue response of metallic meta-biomaterials fabricated with selective laser melting. Towards that end, we designed and additively manufactured Co-Cr meta-biomaterials with three types of repeating unit cells and three to four porosities per type of repeating unit cell. The AM meta-biomaterials were then mechanically tested to obtain their normalized S-N curves. The obtained S-N curves of Co-Cr meta-biomaterials were compared to those of meta-biomaterials with same topological designs but made from other materials, i.e. Ti-6Al-4V, tantalum, and pure titanium, available from our previous studies. We found the material type to be far more important than the topological design in determining the normalized fatigue strength of our AM metallic meta-biomaterials. This is the opposite of what we have found for the quasi-static mechanical properties of the same meta-biomaterials. The effects of material type, manufacturing imperfections, and topological design were different in the high and low cycle fatigue regions. That is likely because the cyclic response of meta-biomaterials depends not only on the static and fatigue strengths of the bulk material but also on other factors that may include strut roughness, distribution of the micro-pores created inside the struts during the AM process, and plasticity. Statement of significance Meta-biomaterials are a special class of metamaterials with unusual or unprecedented combinations of mechanical, physical (e.g. mass transport), and biological properties. Topologically complex and additively manufactured meta-biomaterials have been shown to improve bone regeneration and osseointegration. The mechanical properties of such biomaterials are directly related to their topological design and material type. However, previous studies of such biomaterials have largely neglected the effects of material type, instead focusing on topological design. We show here that neglecting the effects of material type is unjustified. We studied the isolated and combined effects of topological design and material type on the normalized S-N curves of metallic bone-mimicking biomaterials and found them to be more strongly dependent on the material type than topological design.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Cellular and Composite Structures · Additive Manufacturing Materials and Processes · Bone Tissue Engineering Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. Three-dimensional optical metamaterial with a negative refractive index10.1038/nature07247 ↗
2. Twisted optical metamaterials for planarized ultrathin broadband circular polarizers10.1038/ncomms1877 ↗
3. Asymmetric transmission of linearly polarized light at optical metamaterials10.1103/PhysRevLett.104.253902 ↗
4. Negative index of refraction in optical metamaterials10.1364/OL.30.003356 ↗
5. Micro-/nanostructured mechanical metamaterials10.1002/adma.201201644 ↗
6. Interface histology of unloaded and early loaded partially stabilized zirconia endosseous implant in initial bone healing10.1016/0022-3913(93)90289-Z ↗
7. Additively manufactured metallic pentamode meta-materials10.1063/1.4977561 ↗
8. Mechanical meta-materials10.1039/C6MH00065G ↗
9. Acoustic metamaterials for new two-dimensional sonic devices10.1088/1367-2630/9/9/323 ↗
10. Acoustic cloaking in three dimensions using acoustic metamaterials10.1063/1.2803315 ↗
11. Focusing ultrasound with an acoustic metamaterial network10.1103/PhysRevLett.102.194301 ↗
12. Relationship between unit cell type and porosity and the fatigue behavior of selective laser melted meta-biomaterials10.1016/j.jmbbm.2014.12.015 ↗
13. Effects of silica and zinc oxide doping on mechanical and biological properties of 3D printed tricalcium phosphate tissue engineering scaffolds10.1016/j.dental.2011.09.010 ↗
14. Improvement of mechanical and biological properties of porous CaSiO 3 scaffolds by poly (d, l-lactic acid) modification10.1016/j.actbio.2007.08.010 ↗
15. Porous scaffold design for tissue engineering10.1038/nmat1421 ↗
16. Hydrogels for tissue engineering: scaffold design variables and applications10.1016/S0142-9612(03)00340-5 ↗
17. Bone tissue engineering using human mesenchymal stem cells: effects of scaffold material and medium flow10.1023/B:ABME.0000007796.48329.b4 ↗
18. Compression-compression fatigue of selective electron beam melted cellular titanium (Ti-6Al-4V)10.1002/jbm.b.31901 ↗
19. The influence of cell morphology on the compressive fatigue behavior of Ti-6Al-4V meshes fabricated by electron beam melting10.1016/j.jmbbm.2016.01.034 ↗
20. Ti–6Al–4V triply periodic minimal surface structures for bone implants fabricated via selective laser melting10.1016/j.jmbbm.2015.06.024 ↗
21. Relationship between unit cell type and porosity and the fatigue behavior of selective laser melted meta-biomaterials10.1016/j.jmbbm.2014.12.015 ↗
22. Fatigue behavior of porous biomaterials manufactured using selective laser melting10.1016/j.msec.2013.08.006 ↗
23. Mechanical properties of open-cell rhombic dodecahedron cellular structures10.1016/j.actamat.2012.01.052 ↗
24. Additively manufactured open-cell porous biomaterials made from six different space-filling unit cells: the mechanical and morphological properties10.3390/ma8041871 ↗
25. Analytical relationships for the mechanical properties of additively manufactured porous biomaterials based on octahedral unit cells10.1016/j.apm.2017.01.076 ↗
26. Ultralight, ultrastiff mechanical metamaterials10.1126/science.1252291 ↗
27. Mechanical properties of additively manufactured thick honeycombs10.3390/ma9080613 ↗
28. Porous tantalum structures for bone implants: fabrication, mechanical and in vitro biological properties10.1016/j.actbio.2010.01.046 ↗
29. Advanced lightweight 316L stainless steel cellular lattice structures fabricated via selective laser melting10.1016/j.matdes.2013.10.027 ↗
30. The influence of processing parameters on the mechanical properties of selectively laser melted stainless steel microlattice structures10.1115/1.4001743 ↗
31. Synthesis and properties of topologically ordered porous magnesium10.1016/j.mseb.2011.04.006 ↗
32. A novel manufacturing route for fabrication of topologically-ordered porous magnesium scaffolds10.1002/adem.201100029 ↗
33. Mechanical properties of a Ti6Al4V porous structure produced by selective laser melting10.1016/j.matdes.2013.01.038 ↗
34. Fatigue behavior of thin-walled grade 2 titanium samples processed by selective laser melting. Application to life prediction of porous titanium implants10.1016/j.jmbbm.2013.08.011 ↗
35. Mechanical evaluation of porous titanium (Ti6Al4V) structures with electron beam melting (EBM)10.1016/j.jmbbm.2009.10.006 ↗
36. C. Han, X. Chen, J. Tan, Y. Yao, Q. Wei, Z. Zhang, Y. Shi, Surface modification on a porous Co-Cr scaffold fabricated by selective laser melting for bone implant applications.
37. Effects of the unit cell topology on the compression properties of porous Co-Cr scaffolds fabricated via selective laser melting10.1108/RPJ-08-2015-0114 ↗
38. Revival of pure titanium for dynamically loaded porous implants using additive manufacturing10.1016/j.msec.2015.05.001 ↗
39. Additively manufactured porous tantalum implants10.1016/j.actbio.2014.12.003 ↗
40. R. Hedayati, S.M. Ahmadi, K. Lietaert, B. Pouran, Y. Li, H. Weinans, C.D. Rans, A.A. Zadpoor, Isolated and modulated effects of topology and material type on the mechanical properties of additively manufactured porous biomaterials. Submitted.
41. Standard, I., ISO 13314: 2011 (E), Mechanical testing of metals—ductility testing—compression test for porous and cellular metals, Ref Number ISO. 13314(13314), 2011, p. 1–7.
42. Zheng · 2017
43. Analytical relationships for prediction of the mechanical properties of additively manufactured porous biomaterials10.1002/jbm.a.35855 ↗
44. ASTM F75 CoCr Alloy, A.E. system, Editor., Mölndal, Sweden.
45. Fatigue and life prediction for cobalt-chromium stents: a fracture mechanics analysis10.1016/j.biomaterials.2005.10.012 ↗
46. Comparison of fatigue properties and fatigue crack growth rates of various implantable metals10.3390/ma5122981 ↗
47. Defects-tolerant Co-Cr-Mo dental alloys prepared by selective laser melting10.1016/j.dental.2015.09.003 ↗
48. Computational prediction of the fatigue behavior of additively manufactured porous metallic biomaterials10.1016/j.ijfatigue.2015.11.017 ↗
49. Fatigue damage editing for accelerated durability testing using strain range and SWT parameter criteria10.1016/S0142-1123(97)00079-0 ↗
50. Multiaxial fatigue life prediction for titanium alloy TC4 under proportional and nonproportional loading10.1016/j.ijfatigue.2013.08.028 ↗
51. A critical plane approach to multiaxial fatigue damage including out-of-phase loading10.1111/j.1460-2695.1988.tb01169.x ↗
52. J. Morrow, Cyclic plastic strain energy and fatigue of metals, in Internal friction, damping, and cyclic plasticity, ASTM International, 1965.
53. Fatigue analysis of shape memory alloys: energy approach10.1088/0964-1726/14/5/017 ↗
54. Elastic modulus and hardness of cortical and trabecular bone lamellae measured by nanoindentation in the human femur10.1016/S0021-9290(99)00111-6 ↗
55. Comparison of the elastic and yield properties of human femoral trabecular and cortical bone tissue10.1016/S0021-9290(03)00257-4 ↗
56. Mechanical properties and the hierarchical structure of bone10.1016/S1350-4533(98)00007-1 ↗
57. Functionally graded Co–Cr–Mo coating on Ti–6Al–4V alloy structures10.1016/j.actbio.2007.10.005 ↗
58. Biocompatibility and osteogenesis of refractory metal implants, titanium, hafnium, niobium, tantalum and rhenium10.1016/S0142-9612(00)00275-1 ↗
59. Osteostatin-coated porous titanium can improve early bone regeneration of cortical bone defects in rats10.1089/ten.tea.2014.0476 ↗
60. Selective laser melting-produced porous titanium scaffolds regenerate bone in critical size cortical bone defects10.1002/jor.22293 ↗
61. Biomechanical implant fixation of CoCrMo coating inferior to titanium coating in a canine implant model10.1002/jbm.a.32709 ↗
62. Osseointegration enhancement by Zr doping of Co-Cr-Mo implants fabricated by electron beam melting
63. Mechanical behavior of regular open-cell porous biomaterials made of diamond lattice unit cells10.1016/j.jmbbm.2014.02.003 ↗