journal article·2013-05

Structure–property-processing correlations in freeze-cast composite scaffolds

Philipp M. Hunger, Amalie E. Donius, Ulrike G.K. Wegst

Acta Biomaterialia· Volume 9· Issue 5
Publisher page

Abstract

Surprisingly few reports have been published, to date, on the structure-property-processing correlations observed in freeze-cast materials directionally solidified from polymer solutions, or ceramic or metal slurries. The studies that exist focus on properties of sintered ceramics, that is materials whose structure was altered by further processing. In this contribution, we report first results on correlations observed in alumina-chitosan-gelatin composites, which were chosen as a model system to test and compare the effect of particle size and processing parameters on their mechanical properties at a specific composition. Our study reveals that highly porous (>90%) hybrid materials can be manufactured by freeze casting, through the self-assembly of a polymer and a ceramic phase that occurs during directional solidification, without the need of additional processing steps such as sintering or infiltration. It further illustrates that the properties of freeze-cast hybrid materials can independently be tailored at two levels of their structural hierarchy, allowing for the simultaneous optimization of both mechanical and structural requirements. An increase in freezing rate resulted in decreases in lamellar spacing, cell wall thickness, pore aspect ratio and cross-sectional area, as well as increases in both Young's modulus and compressive yield strength. The mechanical properties of the composite scaffolds increased with an increasing particle size. The results show that both structure and mechanical properties of the freeze-cast composites can be custom-designed and that they are thus ideally suited for a large variety of applications that require high porosity at low or medium load-bearing capacity.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Bone Tissue Engineering Materials · Additive Manufacturing and 3D Printing Technologies · Innovations in Concrete and Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. On the mechanism of dewatering colloidal aqueous solutions by freeze–thaw processes10.1016/0043-1354(80)90156-6 ↗
2. Formation of anisotropic ice–agar composites by directional freezing10.1007/BF01451524 ↗
3. Mechanism of lamellar spacing adjustment in directionally frozen agar gels10.1007/BF01412789 ↗
4. Pore structure of porous ceramics synthesized from water-based slurry by freeze-dry process10.1023/A:1017946518955 ↗
5. Synthesis of porous silicon nitride with unidirectionally aligned channels using freeze-drying process10.1111/j.1151-2916.2002.tb00426.x ↗
6. Freeze casting of hydroxyapatite scaffolds for bone tissue engineering10.1016/j.biomaterials.2006.06.028 ↗
7. Freeze-cast hydroxyapatite scaffolds for bone tissue engineering applications10.1088/1748-6041/3/2/025005 ↗
8. In vitro cellular response to hydroxyapatite scaffolds with oriented pore architectures10.1016/j.msec.2009.04.016 ↗
9. Tu(r)ning weakness to strength10.1016/j.nantod.2010.08.001 ↗
10. Tough, bio-inspired hybrid materials10.1126/science.1164865 ↗
11. Hunger PM, Donius AE, Wegst UGK. Platelets self-assemble into porous nacre during freeze casting. J Mech Behav Biomed Mater. http://dx.doi.org/10.1016/j.bbr.2011.03.031.10.1016/j.bbr.2011.03.031 ↗
12. Freeze casting of porous hydroxyapatite scaffolds. I. Processing and general microstructure10.1002/jbm.b.30997 ↗
13. Architectural control of freeze-cast ceramics through additives and templating10.1111/j.1551-2916.2009.03087.x ↗
14. Fabrication of titanium scaffolds with porosity and pore size gradients by sequential freeze casting10.1016/j.matlet.2009.04.012 ↗
15. Control of pore structure and size in freeze-dried collagen sponges10.1002/jbm.1028 ↗
16. Preparation of NiO–YSZ tubular support with radially aligned pore channels10.1016/S0167-577X(02)01002-9 ↗
17. Formation of monolithic silica gel microhoneycombs (SMHs) using pseudosteady state growth of microstructural ice crystals10.1039/b316597c ↗
18. Directionally solidified biopolymer scaffolds: mechanical properties and endothelial cell responses10.1007/s11837-010-0112-9 ↗
19. Le · 2010
20. Biomaterials by freeze casting10.1098/rsta.2010.0014 ↗
21. Porous ceramic scaffolds with complex architectures10.1007/s11837-008-0072-5 ↗
22. Ceramics with special porous structures fabricated by freeze-gelcasting: using tert-butyl alcohol as a template10.1111/j.1551-2916.2007.01957.x ↗
23. The sedimentation of a suspension of uniform spheres under conditions of viscous flow10.1016/0009-2509(54)85015-9 ↗
24. Baehr · 2006
25. Ice-templated porous alumina structures10.1016/j.actamat.2006.11.003 ↗
26. Aligned two- and three-dimensional structures by directional freezing of polymers and nanoparticles10.1038/nmat1487 ↗
27. Gibson · 2001
28. The properties of foams and lattices10.1098/rsta.2005.1678 ↗
29. Shackelford · 2000
30. Design of a multiphase osteochondral scaffold. II. Fabrication of a mineralized collagen–glycosaminoglycan scaffold10.1002/jbm.a.32361 ↗
31. Hydroxyapatite and gelatin composite foams processed via novel freeze-drying and crosslinking for use as temporary hard tissue scaffolds10.1002/jbm.a.30168 ↗
32. Synthesis and characterization of macroporous chitosan/calcium phosphate composite scaffolds for tissue engineering10.1002/1097-4636(20010605)55:3<304::AID-JBM1018>3.0.CO;2-J ↗
33. Preparation and characterization of homogeneous hydroxyapatite/chitosan composite scaffolds via in-situ hydration10.4236/jbnb.2010.11006 ↗