journal article·2010-12

Zirconia nanoparticles prepared by laser vaporization as fillers for dental adhesives

Ulrich Lohbauer, Andrea Wagner, Renan Belli, Christian Stoetzel, Andrea Hilpert, Heinz-Dieter Kurland, Janet Grabow, Frank A. Müller

Acta Biomaterialia· Volume 6· Issue 12
Publisher page

Abstract

Zirconia nanoparticles prepared by laser vaporization were incorporated into the primer or into the adhesive of a commercial adhesive system in order to evaluate its effect on bond strength to dentin. Zirconia nanoparticles (20-50nm) were prepared using a particular laser vaporization technique and incorporated into the primer (P) or into the adhesive (A) of the Adper Scotchbond Multi-Purpose (SBMP) system at 5, 10, 15 and 20wt.% by means of mechanical mixing (stirring) and ultrasonication. Control (unfilled) and experimental groups (filled) were applied, according to the manufacturer's instructions, onto flat mid-coronal human dentin. Composite crowns were built up, stored in distilled water for 24h at 37°C and cut into 0.65±0.05mm² beams following a non-trimming microtensile technique. Specimens were fractured in tension using a universal testing machine (Zwick) and examined by scanning electron microscopy for fractographic analysis. Microtensile bond strength (μTBS) data were analyzed using a two-way ANOVA and modified LSD test at α=0.05. Analysis of the nanofiller distribution and ultramorphological characterization of the interface were performed by transmission electron microscopy (TEM). Zirconia nanoparticle incorporation into the primer or into the adhesive of SBMP significantly increased μTBS to dentin. Filler concentration only affected μTBS significantly in the P group. Statistically significant differences between groups P and A occurred only at 20wt.% filler content, with a significantly higher μTBS in group P. TEM micrographs revealed nanoparticle deposition on top of a hybrid layer when incorporated into the primer, whereas they remained dispersed through the adhesive layer in group A. Zirconia nanoparticles incorporation into SBMP increased bond strength to dentin by reinforcing the interface adhesive layer. Nanofiller incorporation into the primer solution showed a tendency of increasing bond strength with increasing concentration. At high concentrations (20wt.%) nanofiller incorporation was more efficient in increasing bond strength if incorporated in the primer solution. Adding nanofillers to the primer and to the adhesive solutions resulted in different particle distributions at the interface.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Dental materials and restorations · Glass properties and applications · Dental Erosion and Treatment

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Polymer nanocomposites: the “nano” effect on mechanical properties10.1080/15583720701271278 ↗
2. Molecular mechanisms of failure in polymer nanocomposites10.1103/PhysRevLett.89.058301 ↗
3. Epoxy-silica particulate nanocomposites: chemical interactions, reinforcement and fracture toughness10.1016/j.polymer.2005.08.028 ↗
4. Toughening mechanisms for ceramics
5. Toughness mechanism in semi-crystalline polymer blends: II. High-density polyethylene toughened with calcium carbonate filler particles10.1016/S0032-3861(98)00444-3 ↗
6. Toughening of isostatic polypropylene with CaCO3 particles10.1016/S0032-3861(02)00193-3 ↗
7. Nanoparticle alignment and repulsion during failure of glassy polymer nanocomposites10.1021/ma061210k ↗
8. Effect of nanoparticle mobility on toughness of polymer nanocomposites10.1002/adma.200400984 ↗
9. Healing surface defects with nanoparticle-filled polymer coatings: effect of particle geometry10.1021/ma0515127 ↗
10. Nanofiller loading level: influence on selected properties of an adhesive resin10.1016/j.jdent.2009.01.001 ↗
11. Effect of the hydrophilic nanofiller loading on the mechanical properties and the microtensile bond strength of an ethanol-based one-bottle dentin adhesive10.1002/jbm.b.30153 ↗
12. Hydroxyapatite nanorods as novel fillers for improving the properties of dental adhesives: synthesis and application10.1016/j.dental.2010.01.005 ↗
13. Four-year water degradation of total-etch adhesives bonded to dentin10.1177/154405910308200212 ↗
14. In vivo degradation of resin–dentin bonds in humans over 1 to 3 years10.1177/00220345000790060601 ↗
15. Influence of filler addition to bonding agents on shear bond strength to bovine dentin10.1016/0109-5641(95)80055-7 ↗
16. Effect of filler addition on the bonding parameters of dentin bonding adhesives bonded to human dentin
17. Effects of adhesive composition on microtensile bond strength to human dentin
18. Magnetic iron oxide nanopowders produced by CO2 laser evaporation – “in situ” coating and particle embedding in a ceramic matrix10.1016/j.jmmm.2009.02.042 ↗
19. Preparation of spherical titania nanoparticles by CO2 laser evaporation and process integrated particle coating10.1111/j.1551-2916.2009.03589.x ↗
20. Production of nanoscaled powders by CO2 laser evaporation
21. In vivo influence of residual moisture on microtensile bond strength of one-bottle adhesives10.1111/j.1708-8240.2002.tb00145.x ↗
22. Adhesion testing of dentin bonding agents: a review10.1016/0109-5641(95)80046-8 ↗
23. A TEM study of two water-based adhesive systems bonded to dry and wet dentin10.1177/00220345980770010501 ↗
24. Correlative transmission electron microscopy examination of nondemineralized and demineralized resin–dentin interfaces formed by two dentin adhesive systems10.1177/00220345960750030401 ↗
25. Perspective on the development of high-toughness ceramics10.1111/j.1151-2916.1990.tb06493.x ↗
26. Microfracture mechanisms of dental resin composites containing spherically-shaped filler particles10.1177/00220345940730020301 ↗
27. Toughenability of polymers10.1016/S0032-3861(03)00546-9 ↗
28. An investigation into the fracture behavior of a particulate-filled bis-GMA resin10.1177/00220345870660060701 ↗
29. The effect of interfacial bonding on the toughness of glass filled polymers10.1016/0025-5416(71)90087-5 ↗
30. Reduction of composite contraction stress through non-bonded microfiller particles10.1016/S0109-5641(98)00036-0 ↗
31. Influence of nanoparticles on miscibility of polymer blends: a simple theory10.1021/ma0482821 ↗
32. Radiopaque dental adhesives: dispersion of flame-made Ta2O5/SiO2 nanoparticles in methacrylic matrices10.1016/j.jdent.2008.04.010 ↗
33. Parametric study of the effect of phase anisotropy on the micromechanical behavior of dentin–adhesive interfaces10.1098/rsif.2005.0029 ↗
34. Distribution of nanofillers from a simplified-step adhesive in acid-conditioned dentin
35. Simulation of hard particles in a phase-separating binary mixture10.1103/PhysRevLett.82.4026 ↗
36. Effect of polymer–filler surface interactions on the phase separation in polymer blends10.1016/S0032-3861(01)00632-2 ↗
37. Determining the phase behavior of nanoparticle-filled binary blends10.1002/polb.20887 ↗
38. Electrobond improves immediate dentin microtensile bond strength of two etch-and-rinse adhesives
39. Influence of chlorhexidine concentration on the durability of etch-and-rinse dentin bonds: a 12-month in vitro study